M
Low-Voltage, Quad, S PDT,
CMOS Analog S witc h
2
_______________________________________________________________________________________
Voltage Referenced to GND
V+ .......................................................................-0.3V to +17V
V-........................................................................+0.3V to -17V
V+ to V-...............................................................-0.3V to +17V
COM_, NO_, NC_, IN_ (Note 1)..................(V- - 2V) to (V+ + 2V)
or 30mA, whichever occurs first
Continuous Current, Any Pin...............................................30mA
Peak Current, Any Pin
(pulsed at 1ms, 10% duty cycle max) ..........................100mA
Continuous Power Dissipation (T
A
= +70°C)
Plastic DIP (derate 10.53mW/°C above+70°C) ...........842mW
Narrow SO (derate 8.70mW/°C above +70°C) ............696mW
CERDIP (derate 10.00mW/°C above +70°C)...............800mW
Operating Temperature Ranges
MAX394C_ P.......................................................0°C to +70°C
MAX394E_ P....................................................-40°C to +85°C
MAX394MJ P ..................................................-55°C to +125°C
Storage Temperature Range.............................-65°C to +150°C
Lead Temperature (soldering, 10sec) .............................+300°C
ELECTRICAL CHARACTERISTICS—Dual Supplies
(V+ = 5V ±10%, V- = -5V ±10%, GND = 0V, V
INH
= 2.4V, V
INL
= 0.8V, T
A
= T
MIN
to T
MAX
, unless otherwise noted.)
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
Note 1:
Signals on NC, NO, COM, or IN exceeding V+ or V- are clamped by internal diodes. Limit forward diode current to
maximum current rating.
ABSOLUTE MAXIMUM RATINGS
PARAMETER
SYMBOL
MIN
TYP
(Note 2)
MAX
UNITS
On-Resistance
R
ON
C, E, M
20
20
35
30
Analog Signal Range
V
COM
,
V
NO
,
V
NC
V-
V+
V
On-Resistance Flatness
(Note 4)
R
FLAT(ON)
4
-0.2
-0.1
-0.01
-0.01
0.2
0.1
NC or NO Off Leakage Current
(Note 5)
I
NC(OFF)
or
I
NO(OFF)
nA
-2.5
-20
-0.4
-0.2
2.5
20
0.4
0.2
V
NC or
V
NO
= 3V, 0V,
-3V; I
COM
= 10mA,
V+ = 5V; V- = -5V
V+ = 4.5V, V- = -4.5V,
V
NC or
V
NO
= ±3.5V,
I
COM
= 10mA,
V
INH
= 2.4V,
V
INL
= 0.8V
V
COM
= ±4.5V,
V
NC
or V
NO
= ±4.5V,
V+ = 5.5V,V- = -5.5V
(Note 3)
T
A
=
+25°C
T
A
= T
MIN
to T
MAX
T
A
=
+25°C
T
A
= T
MIN
to T
MAX
T
A
=
+25°C
T
A
= T
MIN
to T
MAX
T
A
=
+25°C
T
A
= T
MIN
to T
MAX
C, E
M
C, E
M
6
C, E
M
CONDITIONS
TEMP.
RANGE
C, E, M
C, E, M
C, E
M
-0.04
-0.04
COM Leakage Current
(Note 5)
I
COM(ON)
nA
-5.0
-20
5.0
20
V
COM
= ±4.5V,
V
NC
or V
NO
= ±4.5V,
V+ = 5.5V, V- = -5.5V
T
A
=
+25°C
T
A
= T
MIN
to T
MAX
C, E
M
45
0.5
2
On-Resistance Match Between
Channels (Note 4)
R
ON
V
NC or
V
NO
= ±3V,
I
COM
= 10mA,
V+ = 5V, V- = -5V
4
C, E, M
C, E, M
SWITCH