- 您現在的位置：買賣IC網 > PDF目錄384666 > MAX381CPE (MAXIM INTEGRATED PRODUCTS INC) Precision, Low-Voltage Analog Switches PDF資料下載
參數資料
| 型號： | MAX381CPE |
| 廠商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分類： | 運動控制電子 |
| 英文描述： | Precision, Low-Voltage Analog Switches |
| 中文描述： | DUAL 1-CHANNEL, SGL POLE SGL THROW SWITCH, PDIP16 |
| 封裝： | 0.300 INCH, PLASTIC, DIP-16 |
| 文件頁數： | 8/12頁 |
| 文件大小： | 125K |
| 代理商： | MAX381CPE |
M
Prec ision, Low-Voltage Analog S witc hes
8
_______________________________________________________________________________________
__________Applic ations Information
Operation with S upply V oltages
Other than ±5V
The MAX381/MAX383/MAX385 switches operate with
±3.0V to ±8V bipolar supplies and a +3V to +15V single
supply. In either case, analog signals ranging from V+ to
V- can be switched. The Typical Operating Characteristics
graphs show the typical on-resistance variation with ana-
log signal and supply voltage. The usual on-resistance
temperature coefficient is 0.5%/°C (typ).
Overvoltage Protec tion
Proper power-supply sequencing is recommended for
all CMOS devices. Do not exceed the absolute maxi-
mum ratings, because stresses beyond the listed rat-
ings can cause permanent damage to the devices.
Always sequence V+ on first, then V-, followed by the
logic inputs, NO, or COM. If power-supply sequencing
is not possible, add two small signal diodes (D1, D2) in
series with supply pins for overvoltage protection
(Figure 1). Adding diodes reduces the analog signal
range to one diode drop below V+ and one diode drop
above V-, but does not affect the devices’ low switch
resistance and low leakage characteristics. Device
operation is unchanged, and the difference between
V+ and V- should not exceed 17V. These protection
diodes are not recommended when using a single 3V
supply.
______________________________________________________________Pin Desc ription
COM
V-
V+
NO
* INTERNAL PROTECTION DIODES
D2
D1
-5V
+5V
MAX381
MAX383
MAX385
*
*
*
*
Figure 1. Overvoltage Protection Using Two External Blocking
Diodes
1, 8
COM_
Analog Switch Common Terminal
2–7, 12
N.C.
Not Internally Connected
9, 16
NO_
Analog Switch Normally Open Terminal
—
NC_
Analog Switch Normally Closed Terminal
10, 15
IN_*
Logic Level Input (Normally Low)
11
V+
Analog Signal and Logic Positive Supply Input
14
V-
Analog Signal Negative Supply Input
NAME
FUNCTION
MAX381
1, 3, 6, 8
2, 7, 12
9, 16
4, 5
10, 15
11
14
MAX383
1, 3, 6, 8
2, 7, 12
4, 5, 9, 16
—
10, 15
11
14
MAX385
PIN
13
GND
Logic Negative Supply Input (Ground)
13
13
* IN1 controls COM1 and COM3; IN2 controls COM2 and COM4.
相關PDF資料 |
PDF描述 |
|---|---|
| MAX381CSE | Precision, Low-Voltage Analog Switches |
| MAX381EPE | Precision, Low-Voltage Analog Switches |
| MAX381ESE | Precision, Low-Voltage Analog Switches |
| MAX383CSE | Precision, Low-Voltage Analog Switches |
| MAX383EJE | Precision, Low-Voltage Analog Switches |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX381CPE+ | 功能描述:模擬開關 IC Precision SPST CMOS RoHS:否 制造商:Texas Instruments 開關數量:2 開關配置:SPDT 開啟電阻（最大值）:0.1 Ohms 切換電壓（最大）: 開啟時間（最大值）: 關閉時間（最大值）: 工作電源電壓:2.7 V to 4.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:DSBGA-16 |
| MAX381CSE | 功能描述:模擬開關 IC RoHS:否 制造商:Texas Instruments 開關數量:2 開關配置:SPDT 開啟電阻（最大值）:0.1 Ohms 切換電壓（最大）: 開啟時間（最大值）: 關閉時間（最大值）: 工作電源電壓:2.7 V to 4.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:DSBGA-16 |
| MAX381CSE+ | 功能描述:模擬開關 IC Precision SPST CMOS RoHS:否 制造商:Texas Instruments 開關數量:2 開關配置:SPDT 開啟電阻（最大值）:0.1 Ohms 切換電壓（最大）: 開啟時間（最大值）: 關閉時間（最大值）: 工作電源電壓:2.7 V to 4.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:DSBGA-16 |
| MAX381CSE+T | 功能描述:模擬開關 IC Precision SPST CMOS RoHS:否 制造商:Texas Instruments 開關數量:2 開關配置:SPDT 開啟電阻（最大值）:0.1 Ohms 切換電壓（最大）: 開啟時間（最大值）: 關閉時間（最大值）: 工作電源電壓:2.7 V to 4.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:DSBGA-16 |
| MAX381CSE-T | 功能描述:模擬開關 IC RoHS:否 制造商:Texas Instruments 開關數量:2 開關配置:SPDT 開啟電阻（最大值）:0.1 Ohms 切換電壓（最大）: 開啟時間（最大值）: 關閉時間（最大值）: 工作電源電壓:2.7 V to 4.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:DSBGA-16 |
發(fā)布緊急采購，3分鐘左右您將得到回復。