- 您現在的位置：買賣IC網 > PDF目錄383371 > MAX3725D (Maxim Integrated Products, Inc.) 3.2Gbps SFP Transimpedance Amplifiers with RSSI PDF資料下載
參數資料
| 型號： | MAX3725D |
| 廠商： | Maxim Integrated Products, Inc. |
| 元件分類： | 運動控制電子 |
| 英文描述： | 3.2Gbps SFP Transimpedance Amplifiers with RSSI |
| 中文描述： | 3.2Gbps速率SFP互阻放大器，接收信號強度指示 |
| 文件頁數： | 8/10頁 |
| 文件大?。?/td> | 342K |
| 代理商： | MAX3725D |
M
3.2Gbps SFP Transimpedance
Amplifiers with RSSI
8
_______________________________________________________________________________________
The MAX3724 preamp measures the average photodi-
ode current and provides the information to the output
common mode. The MAX3748A RSSI detect block
senses the common-mode DC level of input signals IN+
and IN- and provides a ground-level-referenced output
signal of the photodiode current. The advantage of this
implementation is that it allows the TIA to be packaged
in a low-cost conventional 4-pin TO-46 header.
The MAX3748A RSSI output is connected to an analog
input channel of the DS1858/DS1859 SFP controller to
convert the analog information into a 16-bit word. The
DS1858/DS1859 provide the received power informa-
tion to the host board of the optical receiver through a
2-wire interface. The DS1859 allows for internal calibra-
tion of the receive power monitor.
The MAX3724 and the MAX3748A have been optimized
to achieve RSSI stability of better than 2.5dB within the
6μA to 500μA range of average input photodiode cur-
rent. To achieve the best accuracy, Maxim recom-
mends receive power calibration to be 6μA at the low
end, and 500μA at the high end of the required range.
Optical Power Relations
Many of the MAX3724/MAX3725 specifications relate to
the input signal amplitude. When working with optical
receivers, the input is sometimes expressed in terms of
average optical power and extinction ratio. Figure 6
and Table 1 show relations that are helpful for convert-
ing optical power to input signal when designing with
the MAX3724/MAX3725. (Refer to Application Note
HFAN–3.0.0:
Accurately Estimating Optical Receiver
Sensitivity
.)
Optical Sensitivity Calculation
The input-referred RMS noise current (I
N
) of the
MAX3724/MAX3725 generally determines the receiver
sensitivity. To obtain a system bit-error rate (BER) of
1E-12, the signal-to-noise ratio must always exceed
14.1. The input sensitivity, expressed in average power,
can be estimated as:
where
ρ
is the photodiode responsivity in A/W and I
N
is
RMS current in amps.
Input Optical Overload
The overload is the largest input that the MAX3724/
MAX3725 can accept while meeting deterministic jitter
specifications. The optical overload can be estimated
in terms of average power with the following equation:
Optical Linear Range
The MAX3724/MAX3725 have high gain, which limits
the output when the input signal exceeds 50μA
P-P
. The
MAX3724/MAX3725 operate in a linear range (10% lin-
earity) for inputs not exceeding:
Linear Range
A
2
r
r
dBm
RMS e
( )
ρ
log
( )
1
=
10
50
1
1000
μ
Overload
mA
2
r
r
dBm
RMS e
( )
ρ
log
( )
1
=
10
1
2
1000
Sensitivity
I r
r
( )
ρ
dBm
( )
1
log
.
=
×
10
14 1
1
2
1000
PARAMETER
SYMBOL
P
AVG
r
e
P
1
P
0
P
IN
RELATION
Average power
Extinction ratio
Optical power of a 1
Optical power of a zero
Signal amplitude
Note:
Assuming 50% average duty cycle and mark density.
P
AVG
= (P
0
+ P
1
) / 2
r
e
= P
1
/ P
0
P
1
= 2P
AVG
(r
e
) / (r
e
+ 1)
P
0
= 2P
AVG
/ (r
e
+ 1)
P
IN
= P
1
- P
0
; P
IN
= 2P
AVG
(r
e
- 1) / (r
e
+ 1)
Table 1. Optical Power Relations
相關PDF資料 |
PDF描述 |
|---|---|
| MAX3724 | 3.2Gbps SFP Transimpedance Amplifiers with RSSI |
| MAX3725 | 3.2Gbps SFP Transimpedance Amplifiers with RSSI |
| MAX3724-MAX3725 | 3.2Gbps SFP Transimpedance Amplifiers with RSSI |
| MAX3724D | 3.2Gbps SFP Transimpedance Amplifiers with RSSI |
| MAX3724E | 3.2Gbps SFP Transimpedance Amplifiers with RSSI |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX3725EVKIT | 制造商:Maxim Integrated Products 功能描述:3.2GBPS SFP TRANSIMPEDANCE AMPLIFIERS WITH RS - Bulk |
| MAX3726UTG+ | 制造商:Maxim Integrated Products 功能描述:LASER PRINTER DRIVER - Rail/Tube |
| MAX3726UTG+T | 制造商:Maxim Integrated Products 功能描述:LASER PRINTER DRIVER - Tape and Reel |
| MAX3727CTE+ | 制造商:Maxim Integrated Products 功能描述:LASER DIODE DRIVER FOR PRINTERS - Rail/Tube |
| MAX3727CTE+T | 制造商:Maxim Integrated Products 功能描述:LASER DIODE DRIVER FOR PRINTERS - Tape and Reel |
發布緊急采購，3分鐘左右您將得到回復。