參數資料
型號: MAX366MJA
廠商: MAXIM INTEGRATED PRODUCTS INC
元件分類: 運動控制電子
英文描述: Signal-Line Circuit Protectors
中文描述: TRIPLE 1-CHANNEL, SGL POLE SGL THROW SWITCH, CDIP8
封裝: 0.300 INCH, CERDIP-8
文件頁數: 9/12頁
文件大小: 103K
代理商: MAX366MJA
M
S ignal-Line Circ uit Protec tors
_______________________________________________________________________________________
9
Figure 6 shows a circuit that can give reliable results.
This circuit uses a 100mV voltage source and a low-
voltage-drop ammeter as the measuring circuit, and an
adjustable supply to sweep the analog voltage across
its whole range. The ammeter must have a voltage
drop of less than one millivolt (at any current) for accu-
rate results. (A Keithley Model 617 Electrometer has a
suitable ammeter circuit, appropriate ranges, and a
built-in voltage source designed for this type of mea-
surement.) Measurements are made by setting the
analog voltage, measuring the current, and calculating
the path resistance. The procedure is repeated at
each analog voltage and supply voltage.
It is important to use a voltage source of 100mV or less.
As shown in Figure 4, this voltage is added to the V
IN
voltage to form the V
OUT
voltage. Using a higher volt-
age could cause the OUT pin to go into a fault condi-
tion prematurely.
High-Frequenc y Performanc e
In 50
systems, signal response is reasonably flat up
to several megahertz (see Typical Operating
Characteristics). Above 5MHz, the response has sev-
eral minor peaks, which are highly layout dependent.
Because the path resistance is dependent on the sup-
ply voltage and signal amplitude, the impedance is not
controlled. Adjacent channel attenuation up to 5MHz is
about 3dB above that of a bare IC socket, and is due
entirely to capacitive coupling.
Pulse response is reasonable, but because the imped-
ance changes rapidly, fast rise times may induce ringing
as the signal approaches the fault voltage. At very high
amplitudes (such as noise spikes), the capacitive cou-
pling across the signal pins will transfer considerable
energy, despite the fact that the DC path is a virtual open
circuit.
MAX366
OUT_
V
IN
4
IN_
V
OUT
V+
V-
V+
V-
PATH RESISTANCE = 100mV/A
100mV
ADJUSTABLE ANALOG VOLTAGE
8
A
Figure 6. Path-Resistance Measuring Circuit
MAX366
OUT1
1
IN1
7
+5V
-5V
OUT2
2
IN2
6
OUT3
3
IN3
5
V+
4
V-
8
P
100k
SWITCHED +5V
OP AMP
Figure 5. Power-Supply Sequencing
相關PDF資料
PDF描述
MAX3670EGJ Low-Jitter 155MHz/622MHz Clock Generator
MAX3670 RECTIFIER STANDARD SINGLE 1A 100V 100 30A-ifsm 5uA-ir 1V-vf A405 5K/REEL-13
MAX368EPN Fault-Protected Analog Multiplexer with Latch
MAX369MJN Fault-Protected Analog Multiplexer with Latch
MAX368CWN Fault-Protected Analog Multiplexer with Latch
相關代理商/技術參數
參數描述
MAX3670EGJ 功能描述:時鐘發生器及支持產品 Low-Jitter 155MHz/622MHz RoHS:否 制造商:Silicon Labs 類型:Clock Generators 最大輸入頻率:14.318 MHz 最大輸出頻率:166 MHz 輸出端數量:16 占空比 - 最大:55 % 工作電源電壓:3.3 V 工作電源電流:1 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-56
MAX3670EGJ-T 功能描述:時鐘發生器及支持產品 Low-Jitter 155MHz/622MHz RoHS:否 制造商:Silicon Labs 類型:Clock Generators 最大輸入頻率:14.318 MHz 最大輸出頻率:166 MHz 輸出端數量:16 占空比 - 最大:55 % 工作電源電壓:3.3 V 工作電源電流:1 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-56
MAX3670ETJ+ 功能描述:時鐘發生器及支持產品 Low-Jitter 155MHz/622MHz RoHS:否 制造商:Silicon Labs 類型:Clock Generators 最大輸入頻率:14.318 MHz 最大輸出頻率:166 MHz 輸出端數量:16 占空比 - 最大:55 % 工作電源電壓:3.3 V 工作電源電流:1 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-56
MAX3670ETJ+T 功能描述:時鐘發生器及支持產品 Low-Jitter 155MHz/622MHz RoHS:否 制造商:Silicon Labs 類型:Clock Generators 最大輸入頻率:14.318 MHz 最大輸出頻率:166 MHz 輸出端數量:16 占空比 - 最大:55 % 工作電源電壓:3.3 V 工作電源電流:1 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-56
MAX3670ETJ+TD 制造商:Maxim Integrated Products 功能描述:CLOCK GEN 32QFN - Tape and Reel