參數資料
型號: MAX362CSE
廠商: MAXIM INTEGRATED PRODUCTS INC
元件分類: 運動控制電子
英文描述: Precision, Quad, SPST Analog Switches
中文描述: QUAD 1-CHANNEL, SGL POLE SGL THROW SWITCH, PDSO16
封裝: SO-16
文件頁數: 6/8頁
文件大?。?/td> 99K
代理商: MAX362CSE
M
Prec ision, Quad, S PS T Analog S witc hes
6
_______________________________________________________________________________________
____________________________Typic al Operating Charac teristic s (c ontinued)
(T
A
= +25°C, unless otherwise noted.)
CHARGE INJECTION vs.
VCOM VOLTAGE
Q
-20
0
20
40
-14
-10
0
10
14
V
COM
(V)
V+ = 15V
V- = -15V
CL = 1nF
CHARGE INJECTION vs.
VCOM VOLTAGE
Q
-10
0
10
0
5
10
12
V
COM
(V)
V+ = 12V
V- = 0V
CL = 1nF
___________Applic ations Information
Operation with S upply V oltages
Other T han ±15V
O
Using supply voltages other than ±15V is reduces the
analog signal range. The MAX361/MAX362 switches
operate with bipolar supplies of ±4.5V to ±20V. Typical
operating characteristic graphs show typical on resis-
tance for ±15V, ±10V, and ±5V supplies. Switching
times increase by a factor of two or more for ±5V oper-
ation. The MAX361/MAX362 can also operate from
+10V to +30V unipolar supplies. Both parts can also
be powered from unbalanced supplies such as +24V
and -5V. Connect V- to 0V when operating with a sin-
gle supply.
Proper power-supply sequencing is recommended for
all CMOS devices. Do not exceed the absolute maxi-
mum ratings, because stresses beyond the listed rat-
ings may cause permanent damage to the devices.
Always sequence V+ on first, followed by V-, and logic
inputs. If power-supply sequencing is not possible,
add two small signal diodes in series with the supply
pins for overvoltage protection (Figure 6). Adding the
diodes reduces the analog signal range to 1V below
V+ and 1V below V-, but low switch resistance and low
leakage characteristics are unaffected. Device opera-
tion is unchanged, and the difference from V+ to V-
should not exceed +44V.
PIN
NAME
MAX361
IN1-IN4
COM1-COM4
MAX362
IN1-IN4
COM1-COM4
FUNCTION
1, 16, 9, 8
2, 15, 10, 7
Logic-level input
Analog switch common terminal
NC (normally closed, MAX361)
NO (normally open, MAX362)
Analog switch terminal
Negative supply voltage input
Ground
Not internally connected
Positive supply voltage input—connected to substrate.
3, 14, 11, 6
NC1-NC4
NO1-NO4
4
5
V-
V-
GND
N.C.
V+
GND
N.C.
V+
12
13
______________________________________________________________Pin Desc ription
相關PDF資料
PDF描述
MAX362EPE Precision, Quad, SPST Analog Switches
MAX362ESE Precision, Quad, SPST Analog Switches
MAX362MJE Precision, Quad, SPST Analog Switches
MAX364-MAX365 Precision, Quad, SPST Analog Switches
MAX365CPE Precision, Quad, SPST Analog Switches
相關代理商/技術參數
參數描述
MAX362CSE+ 功能描述:模擬開關 IC Precision Quad SPST RoHS:否 制造商:Texas Instruments 開關數量:2 開關配置:SPDT 開啟電阻(最大值):0.1 Ohms 切換電壓(最大): 開啟時間(最大值): 關閉時間(最大值): 工作電源電壓:2.7 V to 4.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:DSBGA-16
MAX362CSE+T 功能描述:模擬開關 IC Precision Quad SPST RoHS:否 制造商:Texas Instruments 開關數量:2 開關配置:SPDT 開啟電阻(最大值):0.1 Ohms 切換電壓(最大): 開啟時間(最大值): 關閉時間(最大值): 工作電源電壓:2.7 V to 4.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:DSBGA-16
MAX362CSE-T 功能描述:模擬開關 IC RoHS:否 制造商:Texas Instruments 開關數量:2 開關配置:SPDT 開啟電阻(最大值):0.1 Ohms 切換電壓(最大): 開啟時間(最大值): 關閉時間(最大值): 工作電源電壓:2.7 V to 4.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:DSBGA-16
MAX362EJE 功能描述:模擬開關 IC RoHS:否 制造商:Texas Instruments 開關數量:2 開關配置:SPDT 開啟電阻(最大值):0.1 Ohms 切換電壓(最大): 開啟時間(最大值): 關閉時間(最大值): 工作電源電壓:2.7 V to 4.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:DSBGA-16
MAX362EPE 功能描述:模擬開關 IC RoHS:否 制造商:Texas Instruments 開關數量:2 開關配置:SPDT 開啟電阻(最大值):0.1 Ohms 切換電壓(最大): 開啟時間(最大值): 關閉時間(最大值): 工作電源電壓:2.7 V to 4.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:DSBGA-16