- 您現在的位置：買賣IC網 > PDF目錄383366 > MAX3443EEPA (MAXIM INTEGRATED PRODUCTS INC) 【15kV ESD-Protected, 【60V Fault-Protected, 10Mbps, Fail-Safe RS-485/J1708 Transceivers PDF資料下載
參數資料
| 型號： | MAX3443EEPA |
| 廠商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分類： | 通用總線功能 |
| 英文描述： | 【15kV ESD-Protected, 【60V Fault-Protected, 10Mbps, Fail-Safe RS-485/J1708 Transceivers |
| 中文描述： | LINE TRANSCEIVER, PDIP8 |
| 封裝： | 0.300 INCH, PLASTIC, MS-001AB, DIP-8 |
| 文件頁數： | 14/20頁 |
| 文件大?。?/td> | 368K |
| 代理商： | MAX3443EEPA |
M
±15kV ESD-Protected, ±60V Fault-Protected,
10Mbps, Fail-Safe RS-485/J1708 Transceivers
14
______________________________________________________________________________________
Hot-Swap Capability
Hot-Swap Inputs
Inserting circuit boards into a hot, or powered, back-
plane may cause voltage transients on DE, DE/RE,
RE
,
and receiver inputs A and B that can lead to data errors.
For example, upon initial circuit board insertion, the
processor undergoes a power-up sequence. During this
period, the high-impedance state of the output drivers
makes them unable to drive the MAX3440E
–
MAX3444E
enable inputs to a defined logic level. Meanwhile, leak-
age currents of up to 10μA from the high-impedance out-
put, or capacitively coupled noise from V
CC
or GND,
could cause an input to drift to an incorrect logic state.
To prevent such a condition from occurring, the
MAX3440E
–
MAX3443E feature hot-swap input circuitry
on DE, DE/RE, and
RE
to guard against unwanted dri-
ver activation during hot-swap situations. The
MAX3444E has hot-swap input circuitry only on
RE
.
When V
CC
rises, an internal pulldown (or pullup for
RE
)
circuit holds DE low for at least 10μs, and until the cur-
rent into DE exceeds 200μA. After the initial power-up
sequence, the pulldown circuit becomes transparent,
resetting the hot-swap tolerable input.
Hot-Swap Input Circuitry
At the driver-enable input (DE), there are two NMOS
devices, M1 and M2 (Figure 10). When V
CC
ramps from
zero, an internal 15μs timer turns on M2 and sets the
SR latch, which also turns on M1. Transistors M2, a
2mA current sink, and M1, a 100μA current sink, pull
DE to GND through a 5.6k
resistor. M2 pulls DE to the
disabled state against an external parasitic capaci-
tance up to 100pF that may drive DE high. After 15μs,
the timer deactivates M2 while M1 remains on, holding
DE low against three-state leakage currents that may
drive DE high. M1 remains on until an external current
source overcomes the required input current. At this
time, the SR latch resets M1 and turns off. When M1
turns off, DE reverts to a standard, high-impedance
CMOS input. Whenever V
CC
drops below 1V, the input
is reset.
A complementary circuit for
RE
uses two PMOS
devices to pull
RE
to V
CC
.
__________Applications Information
128 Transceivers on the Bus
The MAX3440E
–
MAX3444E transceivers 1/4-unit-load
receiver input impedance (48k
) allows up to 128
transceivers connected in parallel on one communica-
tion line. Connect any combination of these devices,
and/or other RS-485 devices, for a maximum of 32-unit
loads to the line.
Reduced EMI and Reflections
The MAX3440E/MAX3442E/MAX3444E are slew-rate
limited, minimizing EMI and reducing reflections
caused by improperly terminated cables. Figure 11
shows the driver output waveform and its Fourier analy-
sis of a 125kHz signal transmitted by a MAX3443E.
High-frequency harmonic components with large ampli-
tudes are evident.
Figure 12 shows the same signal displayed for a
MAX3442E transmitting under the same conditions.
Figure 12
’
s high-frequency harmonic components are
much lower in amplitude, compared with Figure 11
’
s,
and the potential for EMI is significantly reduced.
V
CC
TIMER
TIMER
DE
(HOT SWAP)
15
μ
s
100
μ
A
M1
M2
5.6k
2mA
Figure 10. Simplified Structure of the Driver Enable Pin (DE)
相關PDF資料 |
PDF描述 |
|---|---|
| MAX3444EEPA | 【15kV ESD-Protected, 【60V Fault-Protected, 10Mbps, Fail-Safe RS-485/J1708 Transceivers |
| MAX3440EESA | 【15kV ESD-Protected, 【60V Fault-Protected, 10Mbps, Fail-Safe RS-485/J1708 Transceivers |
| MAX3440E-MAX3444E | 【15kV ESD-Protected, 【60V Fault-Protected, 10Mbps, Fail-Safe RS-485/J1708 Transceivers |
| MAX3440E | Single Full-Duplex LVDS Transceiver 8-SOIC -40 to 85 |
| MAX3441E | Single Full-Duplex LVDS Transceiver 8-MSOP -40 to 85 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX3443EEPA+ | 功能描述:RS-485接口IC 10Mbps Fail-Safe RS-485/J1708 Tcvr RoHS:否 制造商:Texas Instruments 數據速率:250 Kbps 工作電源電壓:3.3 V 電源電流:750 uA 工作溫度范圍:- 40 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube |
| MAX3443EESA | 功能描述:RS-485接口IC RoHS:否 制造商:Texas Instruments 數據速率:250 Kbps 工作電源電壓:3.3 V 電源電流:750 uA 工作溫度范圍:- 40 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube |
| MAX3443EESA+ | 功能描述:RS-485接口IC 10Mbps Fail-Safe RS-485/J1708 Tcvr RoHS:否 制造商:Texas Instruments 數據速率:250 Kbps 工作電源電壓:3.3 V 電源電流:750 uA 工作溫度范圍:- 40 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube |
| MAX3443EESA+T | 功能描述:RS-485接口IC 10Mbps Fail-Safe RS-485/J1708 Tcvr RoHS:否 制造商:Texas Instruments 數據速率:250 Kbps 工作電源電壓:3.3 V 電源電流:750 uA 工作溫度范圍:- 40 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube |
| MAX3443EESA-T | 功能描述:RS-485接口IC RoHS:否 制造商:Texas Instruments 數據速率:250 Kbps 工作電源電壓:3.3 V 電源電流:750 uA 工作溫度范圍:- 40 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。