- 您現在的位置：買賣IC網 > PDF目錄383366 > MAX3387EEUG (MAXIM INTEGRATED PRODUCTS INC) 5V High-Speed RS-232 Transceivers with 0.1uF Capacitors PDF資料下載
參數資料
| 型號： | MAX3387EEUG |
| 廠商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分類： | 通用總線功能 |
| 英文描述： | 5V High-Speed RS-232 Transceivers with 0.1uF Capacitors |
| 中文描述： | LINE TRANSCEIVER, PDSO24 |
| 封裝： | 4.40 MM, 0.65 MM PITCH, TSSOP-24 |
| 文件頁數： | 11/16頁 |
| 文件大?。?/td> | 181K |
| 代理商： | MAX3387EEUG |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁當前第11頁第12頁第13頁第14頁第15頁第16頁
M
3V, ±15kV ESD-Protected, AutoShutdown Plus
RS-232 Transceiver for PDAs and Cell Phones
______________________________________________________________________________________
11
IEC 1000-4-2
The IEC 1000-4-2 standard covers ESD testing and
performance of finished equipment; it does not specifi-
cally refer to ICs. The MAX3387E helps you design
equipment that meets Level 4 (the highest level) of IEC
1000-4-2, without the need for additional ESD-protec-
tion components.
The major difference between tests done using the
Human Body Model and IEC 1000-4-2 is higher peak
current in IEC 1000-4-2 because series resistance is
lower in the IEC 1000-4-2 model. Hence, the ESD with-
stand voltage measured to IEC 1000-4-2 is generally
lower than that measured using the Human Body
Model. Figure 6a shows the IEC 1000-4-2 model, and
Figure 6b shows the current waveform for the ±8kV IEC
1000-4-2 Level 4 ESD Contact Discharge test.
The air-gap test involves approaching the device with a
charged probe. The contact-discharge method connects
the probe to the device before the probe is energized.
Machine Model
The Machine Model for ESD tests all pins using a
200pF storage capacitor and zero discharge resis-
tance. Its objective is to emulate the stress caused by
contact that occurs with handling and assembly during
manufacturing. All pins require this protection during
manufacturing, not just RS-232 inputs and outputs.
Therefore, after PC board assembly, the Machine
Model is less relevant to I/O ports.
__________Applications Information
Capacitor Selection
The capacitor type used for C1–C4 is not critical for
proper operation; polarized or nonpolarized capacitors
can be used. The charge pump requires 0.1μF capaci-
tors for 3.3V operation. For other supply voltages, see
Table 2 for required capacitor values. Do not use val-
ues smaller than those listed in Table 2. Increasing the
capacitor values (e.g., by a factor of 2) reduces ripple
on the transmitter outputs and slightly reduces power
consumption. C2, C3, and C4 can be increased without
changing C1’s value. However, do not increase C1
without also increasing the values of C2, C3, and C4 to
maintain the proper ratios (C1 to the other capacitors).
When using the minimum required capacitor values,
make sure the capacitor value does not degrade
excessively with temperature. If in doubt, use capaci-
tors with a larger nominal value. The capacitor’s equiva-
lent series resistance (ESR), which usually rises at low
temperatures, influences the amount of ripple on V+
and V-.
CHARGE-CURRENT
LIMIT RESISTOR
DISCHARGE
RESISTANCE
STORAGE
CAPACITOR
Cs
150pF
R
C
50M to 100M
R
D
330
HIGH-
VOLTAGE
DC
SOURCE
DEVICE
UNDER
TEST
Figure 6a. IEC 1000-4-2 ESD Test Model
tR = 0.7ns to 1ns
30ns
60ns
t
100%
90%
10%
I
P
I
Figure 6b. IEC 1000-4-2 ESD Generator Current Waveform
Table 2. Minimum Required Capacitor
Values
V
CC
(V)
0.1
0.1
C2, C3, C4
(μF)
3.0 to 3.6
0.33
0.047
1
0.22
3.0 to 5.5
4.5 to 5.5
C1
(μF)
相關PDF資料 |
PDF描述 |
|---|---|
| MAX3387ECUG | 5V High-Speed RS-232 Transceivers with 0.1uF Capacitors |
| MAX3387 | Dual LVDS Receiver 8-MSOP -40 to 85 |
| MAX3388EEUG | 2.5V, 【15kV ESD-Protected RS-232 Transceivers for PDAs and Cell Phones |
| MAX3389EEUG | 2.5V, 【15kV ESD-Protected RS-232 Transceivers for PDAs and Cell Phones |
| MAX3388E | Dual LVDS Receiver 8-MSOP -40 to 85 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX3387EEUG+ | 功能描述:RS-232接口集成電路 3V Transceiver for PDAs & Cells RoHS:否 制造商:Exar 數據速率:52 Mbps 工作電源電壓:5 V 電源電流:300 mA 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:LQFP-100 封裝: |
| MAX3387EEUG+T | 功能描述:RS-232接口集成電路 3V Transceiver for PDAs & Cells RoHS:否 制造商:Exar 數據速率:52 Mbps 工作電源電壓:5 V 電源電流:300 mA 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:LQFP-100 封裝: |
| MAX3387EEUG-T | 功能描述:RS-232接口集成電路 RoHS:否 制造商:Exar 數據速率:52 Mbps 工作電源電壓:5 V 電源電流:300 mA 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:LQFP-100 封裝: |
| MAX3387EEUP | 制造商:Maxim Integrated Products 功能描述:- Rail/Tube |
| MAX3388ECUG | 功能描述:RS-232接口集成電路 RoHS:否 制造商:Exar 數據速率:52 Mbps 工作電源電壓:5 V 電源電流:300 mA 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:LQFP-100 封裝: |
發布緊急采購，3分鐘左右您將得到回復。