- 您現在的位置：買賣IC網 > PDF目錄385526 > MAX3353EEUE (MAXIM INTEGRATED PRODUCTS INC) USB On-the-Go Charge Pump with Switchable Pullup/Pulldown Resistors PDF資料下載
參數資料
| 型號： | MAX3353EEUE |
| 廠商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分類： | 穩壓器 |
| 英文描述： | USB On-the-Go Charge Pump with Switchable Pullup/Pulldown Resistors |
| 中文描述： | 0.015 A SWITCHED CAPACITOR REGULATOR, 600 kHz SWITCHING FREQ-MAX, PDSO16 |
| 封裝： | 4.40 MM, MO-153AB, TSSOP-16 |
| 文件頁數： | 17/21頁 |
| 文件大?。?/td> | 386K |
| 代理商： | MAX3353EEUE |
Connect all capacitors as close to the device as possible.
V
BUS
and V
CC
bypass capacitors should have trace
lengths as short as possible
±15kV ESD Protection
To protect the MAX3353E against ESD, D+, D-, ID_IN,
and V
BUS,
have extra protection against static electricity
to protect the device up to ±15kV. The ESD structures
withstand high ESD in all states
—
normal operation,
shutdown, and powered down. In order for the 15kV
ESD structures to work correctly, a 1μF or greater
capacitor must be connected from V
BUS
to GND. ESD
protection can be tested in various ways; D+, D-, ID_IN,
and V
BUS
are characterized for protection to the follow-
ing limits:
1) ±15kV using the Human Body Model
2) ±6kV using the IEC 1000-4-2 Contact Discharge
method
3) ±11kV using the IEC 1000-4-2 Air-Gap Discharge
method
ESD Test Conditions:
ESD performance depends on
a variety of conditions. Contact Maxim for a reliability
report that documents test setup, test methodology,
and test results.
Human Body Model
Figure 11 shows the Human Body Model and Figure 12
shows the current waveform it generates when dis-
charged into a low impedance. This model consists of
a 100pF capacitor charged to the ESD voltage of inter-
est, which is then discharged into the test device
through a 1.5k
resistor.
IEC 1000-4-2
The IEC 1000-4-2 standard covers ESD testing and
performance of finished equipment; it does not specifi-
cally refer to integrated circuits. The major difference
between tests done using the Human Body Model and
IEC 1000-4-2 is a higher peak current in IEC 1000-4-2,
because series resistance is lower in the IEC 1000-4-2
model. Hence, the ESD withstand voltage measured to
IEC 1000-4-2 is generally lower than that measured
using the Human Body Model. Figure 13 shows the IEC
1000-4-2 model. The Air-Gap Discharge test involves
approaching the device with a charged probe. The
Contact Discharge method connects the probe to the
device before the probe is energized. Figure 14 shows
the IEC 1000-4-2 current waveform.
Machine Model
The Machine Model for ESD tests all pins using a
200pF storage capacitor and zero discharge resis-
tance. Its objective is to emulate the stress caused by
contact that occurs with handling and assembly during
manufacturing. All pins require this protection during
manufacturing. The Machine Model is less relevant to
I/O ports after PC board assembly.
Layout Considerations
The MAX3353E high oscillator frequency makes proper
layout important to ensure stability and maintain the
output voltage under all loads. For best performance,
minimize the distance between the capacitors and the
MAX3353E.
UCSP Reliability
For the latest application details on UCSP construction,
dimensions, tape-carrier information, printed circuit board
techniques, bump-pad layout, and recommended reflow
temperature profile as well as the latest information on
reliability testing results, refer to Maxim Application Note:
UCSP
–
A Wafer-Level Chip Scale Package
available on
Maxim
’
s website at www.maxim-ic.com/ucsp.
M
USB On-the-Go Charge Pump with Switchable
Pullup/Pulldown Resistors
______________________________________________________________________________________
17
相關PDF資料 |
PDF描述 |
|---|---|
| MAX3355EEUD | +/-15kV ESD-Protected USB On-the-Go Charge Pump and Comparators in UCSP |
| MAX3386EEUP | 3.0V, 【15kV ESD-Protected RS-232 Transceiver for PDAs and Cell Phones |
| MAX3386E | Dual LVDS Receiver 8-SOIC -40 to 85 |
| MAX3386ECUP | Dual LVDS Receiver 8-MSOP -40 to 85 |
| MAX3387E | +3.0V to +5.5V, 10nA, 250kbps RS-232 Transceivers with ±15kV ESD-Protected I/O and Logic Pins I1(+3.0V至+5.5V,10nA,帶 ±15kV ESD保護接口和邏輯引腳，250kbps RS-232 收發器（3收3發）) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX3353EEUE+ | 功能描述:電荷泵 USB On-the-Go Charge Pump RoHS:否 制造商:Maxim Integrated 功能:Inverting, Step Up 輸出電壓:- 1.5 V to - 5.5 V, 3 V to 11 V 輸出電流:100 mA 電源電流:1 mA 最大工作溫度:+ 70 C 封裝 / 箱體:SOIC-8 Narrow 封裝:Tube |
| MAX3353EEUE+T | 功能描述:電荷泵 USB On-the-Go Charge Pump RoHS:否 制造商:Maxim Integrated 功能:Inverting, Step Up 輸出電壓:- 1.5 V to - 5.5 V, 3 V to 11 V 輸出電流:100 mA 電源電流:1 mA 最大工作溫度:+ 70 C 封裝 / 箱體:SOIC-8 Narrow 封裝:Tube |
| MAX3353EEUE-T | 功能描述:低壓差穩壓器 - LDO RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓（最大值）:307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20 |
| MAX3353EEWP+ | 制造商:Maxim Integrated Products 功能描述:USB ON-THE-GO CHARGE PUMP WITH SWITCHABLE PULLUP/PULLDOWN RE - Rail/Tube |
| MAX3353EEWP+T | 制造商:Maxim Integrated Products 功能描述:USB ON-THE-GO CHARGE PUMP WITH SWITCHABLE PULLUP/PULLDOWN RE - Tape and Reel |
發布緊急采購，3分鐘左右您將得到回復。