- 您現在的位置：買賣IC網 > PDF目錄383362 > MAX324EJA (MAXIM INTEGRATED PRODUCTS INC) CONNECTOR SOCKET POLARIZED GOLD PLATED PDF資料下載
參數資料
| 型號： | MAX324EJA |
| 廠商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分類： | 運動控制電子 |
| 英文描述： | CONNECTOR SOCKET POLARIZED GOLD PLATED |
| 中文描述： | DUAL 1-CHANNEL, SGL POLE SGL THROW SWITCH, CDIP8 |
| 封裝： | 0.300 INCH, CERAMIC, SDIP-8 |
| 文件頁數： | 11/16頁 |
| 文件大?。?/td> | 153K |
| 代理商： | MAX324EJA |
The major difference between tests done using the
Human Body Model and IEC1000-4-2 is higher peak
current in IEC1000-4-2, because series resistance is
lower in the IEC1000-4-2 model. Hence, the ESD with-
stand voltage measured to IEC1000-4-2 is generally
lower than that measured using the Human Body
Model. Figure 7a shows the IEEE1000-4-2 model and
Figure 7b shows the current waveform for the ±8kV
IEC1000-4-2 Level 4 ESD contact-discharge test.
The air-gap test involves approaching the device with a
charged probe. The contact-discharge method connects
the probe to the device before the probe is energized.
Machine Model
The Machine Model for ESD tests all pins using a 200pF
storage capacitor and zero discharge resistance. Its
objective is to emulate the stress caused by contact that
occurs with handling and assembly during manufactur-
ing. Of course, all pins require this protection during
manufacturing, not just RS-232 inputs and outputs.
Therefore, after PC board assembly, the Machine Model
is less relevant to I/O ports.
___________Applications Information
Capacitor Selection
The capacitor type used for C1–C4 is not critical for
proper operation; either polarized or nonpolarized
capacitors may be used. The charge pump requires
0.1μF capacitors for 3.3V operation. For other supply
voltages, refer to Table 3 for required capacitor values.
Do not use values smaller than those listed in Table 3.
Increasing the capacitor values (e.g., by a factor of 2)
reduces ripple on the transmitter outputs and slightly
reduces power consumption. C2, C3, and C4 can be
increased without changing C1’s value.
However, do
not increase C1 without also increasing the values of
C2, C3, and C4 to maintain the proper ratios (C1 to
the other capacitors).
When using the minimum required capacitor values,
make sure the capacitor value does not degrade exces-
sively with temperature. If in doubt, use capacitors with a
larger nominal value. The capacitor’s equivalent series
resistance (ESR) usually rises at low temperatures and
influences the amount of ripple on V+ and V-.
Power-Supply Decoupling
In most circumstances, a 0.1μF V
CC
bypass capacitor is
adequate. In applications that are sensitive to power-
supply noise, use a capacitor of the same value as the
charge-pump capacitor C1. Connect bypass capacitors
as close to the IC as possible.
T ransmitter Outputs
when Exiting S hutdown
Figure 8 shows two transmitter outputs when exiting
shut down mode. As they become active, the two trans-
mitter outputs are shown going to opposite RS-232 lev-
els (one transmitter output is high, the other is low).
Each transmitter is loaded with 3k
in parallel with
1000pF. The transmitter outputs display no ringing or
undesirable transients as they come out of shutdown,
and are enabled only when the magnitude of V-
exceeds approximately -3V.
M
±15kV ESD-Protected, 1μA, 3.0V to 5.5V, 250kbps,
RS -232 Transc eivers with AutoS hutdown
______________________________________________________________________________________
11
0.33
1
0.047
0.22
4.5 to 5.5
3.0 to 5.5
0.1
0.1
3.15 to 3.6
0.22
0.22
3.0 to 3.6
C2, C3, C4
(μF)
C1, C
BYPASS
(μF)
V
CC
(V)
Table 3. Required Capacitor Values
40
μ
s/div
T2OUT
FORCEON =
FORCEOFF
T1OUT
5V/div
2V/div
V
CC
= 3.3V
C1–C4 = 0.1
μ
F
Figure 8. Transmitter Outputs Exiting Shutdown or Powering Up
Table 4. Logic Family Compatibility with
Various Supply Voltages
Compatible with ACT and
HCT CMOS, and with TTL.
Incompatible with AC, HC,
or CD4000 CMOS.
3.3
5
SYSTEM
POWER-
SUPPLY
VOLTAGE
(V)
Compatible with all TTL and
CMOS-logic families.
5
5
Compatible with all CMOS
families.
3.3
3.3
COMPATIBILITY
V
CC
SUPPLY
VOLTAGE
(V)
相關PDF資料 |
PDF描述 |
|---|---|
| MAX324CPA | Precision, Single-Supply, SPST Analog Switches |
| MAX324CSA | Precision, Single-Supply, SPST Analog Switches |
| MAX3221E | Video/Imaging Fixed-Point Digital Signal Processor 548-FCBGA |
| MAX3221ECAE | Video/Imaging Fixed-Point Digital Signal Processor 548-FCBGA |
| MAX3223E | Video/Imaging Fixed-Point Digital Signal Processor 548-FCBGA |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX324EPA | 功能描述:模擬開關 IC RoHS:否 制造商:Texas Instruments 開關數量:2 開關配置:SPDT 開啟電阻（最大值）:0.1 Ohms 切換電壓（最大）: 開啟時間（最大值）: 關閉時間（最大值）: 工作電源電壓:2.7 V to 4.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:DSBGA-16 |
| MAX324EPA+ | 功能描述:模擬開關 IC RoHS:否 制造商:Texas Instruments 開關數量:2 開關配置:SPDT 開啟電阻（最大值）:0.1 Ohms 切換電壓（最大）: 開啟時間（最大值）: 關閉時間（最大值）: 工作電源電壓:2.7 V to 4.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:DSBGA-16 |
| MAX324ESA | 功能描述:模擬開關 IC RoHS:否 制造商:Texas Instruments 開關數量:2 開關配置:SPDT 開啟電阻（最大值）:0.1 Ohms 切換電壓（最大）: 開啟時間（最大值）: 關閉時間（最大值）: 工作電源電壓:2.7 V to 4.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:DSBGA-16 |
| MAX324ESA+ | 功能描述:模擬開關 IC Precision Single Supply SPST RoHS:否 制造商:Texas Instruments 開關數量:2 開關配置:SPDT 開啟電阻（最大值）:0.1 Ohms 切換電壓（最大）: 開啟時間（最大值）: 關閉時間（最大值）: 工作電源電壓:2.7 V to 4.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:DSBGA-16 |
| MAX324ESA+T | 功能描述:模擬開關 IC Precision Single Supply SPST RoHS:否 制造商:Texas Instruments 開關數量:2 開關配置:SPDT 開啟電阻（最大值）:0.1 Ohms 切換電壓（最大）: 開啟時間（最大值）: 關閉時間（最大值）: 工作電源電壓:2.7 V to 4.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:DSBGA-16 |
發布緊急采購，3分鐘左右您將得到回復。