- 您現在的位置：買賣IC網 > PDF目錄383360 > MAX320 (Maxim Integrated Products, Inc.) Precision, Dual-Supply, SPST Analog Switches(接通電阻35Ω,漏電流0.25nA,導通速率175ns,雙電源,單刀單擲CMOS模擬開關) PDF資料下載
參數資料
| 型號： | MAX320 |
| 廠商： | Maxim Integrated Products, Inc. |
| 英文描述： | Precision, Dual-Supply, SPST Analog Switches(接通電阻35Ω,漏電流0.25nA,導通速率175ns,雙電源,單刀單擲CMOS模擬開關) |
| 中文描述： | 高精度、雙電源、SPST、模擬CMOS開關 |
| 文件頁數： | 5/8頁 |
| 文件大?。?/td> | 109K |
| 代理商： | MAX320 |
M
Prec ision, Dual-S upply, S PS T
Analog S witc hes
_______________________________________________________________________________________
5
__________Applic ations Information
Logic Levels
Calculate the logic thresholds typically as follows: V
IH
=
(V+ - 1.5V) and V
IL
= (V+ - 2.5V).
Power-supply consumption is minimized when IN1 and
IN2 are driven with logic-high levels equal to V+ and logic-
low levels well below the calculated V
IL
of (V+ - 2.5V). IN1
and IN2 can be driven to V- without damage.
Analog S ignal Levels
Analog signals that range over the entire supply voltage
(V- to V+) can be switched, with very little change in on-
resistance over the entire voltage range (see Typical
Operating Characteristics). All switches are bidirec-
tional, so NO_, NC_, and COM_ pins can be used as
either inputs or outputs.
Power-S upply S equenc ing
and Overvoltage Protec tion
Do not exceed the absolute maximum ratings, because
stresses beyond the listed ratings may cause perma-
nent damage to the devices.
Proper power-supply sequencing is recommended for
all CMOS devices. Always apply V+, followed by V-,
before applying analog signals or logic inputs, especial-
ly if the analog or logic signals are not current-limited. If
this sequencing is not possible, and if the analog or
logic inputs are not current-limited to <30mA, add two
small signal diodes (D1, D2) as shown in Figure 1.
Adding protection diodes reduces the analog signal
range to a diode drop (about 0.7V) below V+ for D1,
and a diode drop above V- for D2. Leakage is not
affected by adding the diodes. On-resistance increas-
es by a small amount at low supply voltages. Maximum
supply voltage (V- to V+) must not exceed 17V.
Adding protection diode D1 causes the logic thresh-
olds to be shifted relative to the positive power-supply
rail. This can be significant when low positive supply
voltages (+5V or less) are used. Driving IN1 and IN2 all
the way to the supply rails (i.e., to a diode drop higher
than the V+ pin or a diode drop lower than the V- pin) is
always acceptable.
The protection diodes D1 and D2 also protect against
some overvoltage situations. With the circuit of Figure 1,
if the supply voltage is below the absolute maximum
rating and if a fault voltage up to the absolute maximum
rating is applied to an analog signal pin, no damage
will result. For example, with ±5V supplies, analog sig-
nals up to ±8.5V will not damage the circuit of Figure 1.
If only a single fault signal is present, the fault voltage
can rise to +12V or to -12V without damage.
_____________________Pin Desc ription
POSITIVE SUPPLY
COM
D1
D2
NO
V-
Vg
V+
NEGATIVE SUPPLY
MAX320
MAX321
MAX322
Figure 1. Overvoltage Protection Using Two External Blocking
Diodes
5
Normally Closed Analog
Switch Terminal
NC2
(MAX321/MAX322)
Normally Open Analog
Switch Terminal
NO2
(MAX320)
Negative Supply
V-
4
Logic Inputs
IN2, IN1
3, 7
PIN
Analog Switch Common
Terminals
COM1, COM2
2, 6
Normally Closed Analog
Switch Terminal
NC1
(MAX321)
Normally Open Analog
Switch Terminal
NO1
(MAX320/MAX322)
1
FUNCTION
NAME
Positive Supply
V+
8
相關PDF資料 |
PDF描述 |
|---|---|
| MAX320CSA | Precision, Dual-Supply, SPST Analog Switches |
| MAX320CPA | Precision, Dual-Supply, SPST Analog Switches |
| MAX321CPA | Precision, Dual-Supply, SPST Analog Switches |
| MAX321CSA | Precision, Dual-Supply, SPST Analog Switches |
| MAX321EPA | Precision, Dual-Supply, SPST Analog Switches |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX3202EEBS | 制造商:Maxim Integrated Products 功能描述:LOW-CAPACITANCE 2/6-CHANNEL +/-15 - Rail/Tube |
| MAX3202EEBS+ | 制造商:Maxim Integrated Products 功能描述:ESD PROT ARYS 4UCSP - Rail/Tube |
| MAX3202EEBS+T | 功能描述:TVS二極管陣列 RoHS:否 制造商:Littelfuse 極性: 通道:4 Channels 擊穿電壓: 鉗位電壓:11.5 V 工作電壓:2.5 V 峰值浪涌電流:20 A 安裝風格:SMD/SMT 端接類型:SMD/SMT 系列: 最小工作溫度:- 40 C 最大工作溫度:+ 85 C |
| MAX3202EEBS-T | 功能描述:TVS二極管陣列 RoHS:否 制造商:Littelfuse 極性: 通道:4 Channels 擊穿電壓: 鉗位電壓:11.5 V 工作電壓:2.5 V 峰值浪涌電流:20 A 安裝風格:SMD/SMT 端接類型:SMD/SMT 系列: 最小工作溫度:- 40 C 最大工作溫度:+ 85 C |
| MAX3202EETT | 功能描述:TVS二極管陣列 RoHS:否 制造商:Littelfuse 極性: 通道:4 Channels 擊穿電壓: 鉗位電壓:11.5 V 工作電壓:2.5 V 峰值浪涌電流:20 A 安裝風格:SMD/SMT 端接類型:SMD/SMT 系列: 最小工作溫度:- 40 C 最大工作溫度:+ 85 C |
發布緊急采購，3分鐘左右您將得到回復。