M
SPI/MICROWIRE-Compatible UART and ±15kV ESD-
Protected RS-232 Transceivers with Internal Capacitors
2
_______________________________________________________________________________________
ABSOLUTE MAXIMUM RATINGS
V
CC
to GND (MAX3110E) ........................................-0.3V to +6V
V
CC
to GND (MAX3111E).........................................-0.3V to +4V
V+ to GND (Note 1)..................................................-0.3V to +7V
V- to GND (Note 1)...................................................+0.3V to -7V
V+ to V- (Note 1)..................................................................+13V
Input Voltages to GND
CS
, X1,
CTS
, RX, DIN, SCLK.................. -0.3V to (V
CC
+ 0.3V)
T_IN,
SHDN
...........................................................-0.3V to +6V
R_IN..................................................................................±25V
Output Voltage to GND
DOUT,
RTS
, TX, X2 .................................-0.3V to (V
CC
+ 0.3V)
IRQ
.......................................................................-0.3V to +6V
T_OUT ...........................................................................±13.2V
R_OUT.....................................................-0.3V to (V
CC
+ 0.3V)
ELECTRICAL CHARACTERISTICS—MAX3110E
(V
CC
= +4.5V to +5.5V, T
A
= T
MIN
to T
MAX
, unless otherwise noted. Typical values are measured for baud rate set to 9600baud at
V
CC
= +5V, T
A
= +25°C.) (Note 2)
PARAMETER
SYMBOL
CONDITIONS
DC CHARACTERISTICS
(V
CC
= +5V, T
A
= +25°C)
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and function-
al operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure
to absolute maximum rating conditions for extended periods may affect device reliability.
TX,
RTS
Output Current ....................................................100mA
Short-Circuit Duration
X2, DOUT,
IRQ
(to V
CC
or GND).............................Continuous
T_OUT (to GND) .....................................................Continuous
Continuous Power Dissipation (T
A
= +70°C)
28-pin Wide SO (derate 12.5mW/°C above +70°C) ...........1W
28-pin Plastic DIP (derate 14.3mW/°C above +70°C) ....1.14W
Operating Temperature Ranges
MAX311_EC_ _ .................................................. 0°C to +70°C
MAX311_EE_ _ ................................................-40°C to +85°C
Storage Temperature Range ............................-65°C to +150°C
Lead Temperature (soldering, 10sec).............................+300°C
Note 1:
V+ and V- can have maximum magnitudes of 7V, but their absolute difference should not exceed 13V.
SHDNi bit = 1
SHDNi bit = 0
2
Input Current
I
IN1
25
μA
V
X1
= 0 or 5.5V
MIN
TYP
MAX
UNITS
Input Low Voltage
V
IL1
0.2V
CC
V
Input High Voltage
V
IH1
0.7V
CC
V
V
Supply Current with Hardware
and Software Shutdown
UART OSCILLATOR INPUT (X1)
I
CCSHDN(H+ S)
3
20
μA
Input Capacitance
UART LOGIC INPUTS (DIN, SCLK,
CS, CTS
, RX
)
C
IN1
5
pF
Input High Voltage
Input Low Voltage
Input Leakage Current
Input Capacitance
RS-232 LOGIC INPUTS (T_IN,
SHDN)
V
IH2
V
IL2
V
HYST2
I
LKG1
C
IN2
0.7V
CC
V
V
0.3V
CC
Supply Current
Supply Current with Hardware
Shutdown
I
CC
0.6
2
mA
I
CCSHDN(H)
0.48
1
mA
250
mV
μA
pF
±1
5
Input High Voltage
Input Low Voltage
Transmitter Input Hysteresis
Input Leakage Current
V
IH3
V
IL3
V
HYST3
I
IN3
2.4
0.8
V
500
±0.01
mV
μA
±1
SHDN
= GND, SHDNi bit = 1 (Note 4)
V
CC
= 5V
SHDN
= V
CC
, no load
SHDN
= GND (Note 3)