參數資料
型號: MAX3100EEE
廠商: MAXIM INTEGRATED PRODUCTS INC
元件分類: 微控制器/微處理器
英文描述: Dual LVDS Transmitter 8-SOIC -40 to 85
中文描述: 1 CHANNEL(S), 230.4K bps, SERIAL COMM CONTROLLER, PDSO16
封裝: 0.150 INCH, 0.025 INCH PITCH, QSOP-16
文件頁數: 11/24頁
文件大?。?/td> 263K
代理商: MAX3100EEE
M
S PI/Mic rowire-Compatible
UART in QS OP-16
______________________________________________________________________________________
11
IRQ
N
RM MASK
TM MASK
PM MASK
TRANSITION ON RX
SHUTDOWN
RAM MASK
FRAMING ERROR
SHUTDOWN
RAM MASK
R
S
Q
R
NEW DATA AVAILABLE
DATA READ
TRANSMIT BUFFER EMPTY
DATA READ
PE = 1 AND RECEIVED PARITY BIT = 1
PE = 0 OR RECEIVED PARITY BIT = 0
T
Pr
RA
FE
R
S
Q
R
S
Q
Figure 6. Interrupt Sources and Masks Functional Diagram
Table 6. Interrupt Sources and Masks—Bit Descriptions
MEANING
WHEN SET
DESCRIPTION
Received parity bit = 1
Transition on RX when
in shutdown; framing
error when not in
shutdown
RA/FE
RAM
This is the RA (RX-transition) bit in shutdown, and the FE (framing-error) bit in
operating mode. RA is set if there has been a transition on RX since entering
shutdown. RA is cleared when the MAX3100 exits shutdown.
IRQ
is asserted
when RA is set and
RAM
= 1.
FE is determined solely by the currently received data, and is not stored in FIFO.
The FE bit is set if a zero is received when the first stop bit is expected. FE is
cleared upon receipt of the next properly framed character.
IRQ
is asserted
when FE is set and RAM = 1.
MASK
BIT
Pr
PM
The Pr bit reflects the value in the word currently in the receive-buffer register
(oldest data available). The Pr bit is set when parity is enabled (PE = 1) and the
received parity bit is 1. The Pr bit is cleared either when parity is not enabled (PE
= 0), or when parity is enabled and the received bit is 0. An interrupt is issued
based on the oldest Pr value in the receiver FIFO. The oldest Pr value is the next
value that will be read by a Read Data operation.
BIT
NAME
Data available
R
RM
The R bit is set when new data is available to be read from the receive register/
FIFO. FIFO is cleared when all data has been read. An interrupt is asserted as long
as R = 1 and
RM
= 1.
Transmit buffer is
empty
T
TM
The T bit is set when the transmit buffer is ready to accept data.
IRQ
is asserted
low if
TM
= 1 and the transmit buffer becomes empty. This source is cleared on
CS
’s rising edge during a Read Data operation. Although the interrupt is cleared,
T may be polled to determine transmit-buffer status.
Interrupt S ourc es and Masks
A Read Data operation clears the interrupt
IRQ
. Table
6 gives the details for each interrupt source. Figure 6
shows the functional diagram for the interrupt sources
and mask blocks.
相關PDF資料
PDF描述
MAX3174CAI #.3V Multiprotocol Software-Selectable Cable Terminators and Transceivers
MAX3172 Quad LVDS Receiver 16-TSSOP -40 to 85
MAX3172CAI Quad LVDS Receiver 16-TSSOP -40 to 85
MAX3185EWP 5V High-Speed RS-232 Transceivers with 0.1uF Capacitors
MAX3185 3V, ±15kV ESD-Protected, AutoShutdown Plus RS-232 Transceiver for PDAs and Cell Phones(3V, ±15kV ESD保護,自動關斷,用于PDA和蜂窩式手機的RS-232收發器(5收3發))
相關代理商/技術參數
參數描述
MAX3100EEE+ 功能描述:UART 接口集成電路 SPI/uWire Compatible RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
MAX3100EEE+T 功能描述:UART 接口集成電路 SPI/uWire Compatible RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
MAX3100EEE-C78277 制造商:Maxim Integrated Products 功能描述:SPI/MICROWIRE-COMPATIBLE UART IN A QSOP-16 P - Bulk
MAX3100EEE-T 功能描述:UART 接口集成電路 RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
MAX3100EPD 功能描述:UART 接口集成電路 RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel