- 您現在的位置：買賣IC網 > PDF目錄383353 > MAX3022 (Maxim Integrated Products, Inc.) +1.2V to +3.6V. 0.1礎. 100Mbps. 8-Channel Level Translators PDF資料下載
參數資料
| 型號： | MAX3022 |
| 廠商： | Maxim Integrated Products, Inc. |
| 英文描述： | +1.2V to +3.6V. 0.1礎. 100Mbps. 8-Channel Level Translators |
| 中文描述： | 1.2V到3.6V。 0.1礎。 100Mbps的。 8通道電平轉換器 |
| 文件頁數： | 11/18頁 |
| 文件大?。?/td> | 503K |
| 代理商： | MAX3022 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁當前第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁
Detailed Description
The MAX3054/MAX3055/MAX3056 interface between
the protocol controller and the physical wires of the bus
lines in a CAN. The devices provide differential transmit
capability and switch to single-wire mode if certain fault
conditions occur (see the
Failure Management
section).
The MAX3054/MAX3055/MAX3056 guarantee full wake-
up capability during failure modes.
The extended fault-protection range of CANH and
CANL bus lines (±80V) allows for use in 42V automotive
applications. A current-limiting circuit protects the
transmitter output stage against overcurrent faults. This
feature prevents destruction of the transmitter output
stage. If the junction temperature exceeds a value of
approximately +165
°
C, the transmitter output stages
are disabled. The CANH and CANL lines are also pro-
tected against electrical transients, which can occur in
an automotive environment.
The transceiver provides three low-power modes that
can be entered and exited through pins
STB
and EN.
An output INH pin can be used for deactivation of an
external voltage regulator.
The MAX3054/MAX3055/MAX3056 are designed to
provide optimal operation for a specified data rate. The
MAX3054 is ideal for high data rates of 250kbps. The
MAX3055 is used for data rates of 125kbps, and the
MAX3056 is designed for 40kbps applications. For the
40kbps and 125kbps versions, the built-in slope-control
feature allows the use of unshielded cables and receiver
input filters guarantee high noise immunity.
Normal Operation Mode
Transmitter
The transmitter converts a single-ended input (TXD)
from the CAN controller to differential outputs for the
bus lines (CANH, CANL).
Receiver
The receiver takes differential input from the bus lines
(CANH, CANL) and converts this data as a single-
ended output (RXD) to the CAN controller. It consists of
a comparator that senses the difference
V = (CANH -
CANL) with respect to an internal threshold.
BATT
The main function of BATT is to supply power to the
device when vehicle battery voltage is supplied.
BATT can handle up to +80V making it ideal for 42V
automotive systems allowing power-up of the device
when the ignition is turned on.
M
±80V Fault-Protected/Tolerant CAN
Transceivers for In-Car Applications
______________________________________________________________________________________
11
Pin Description
PIN
1
2
3
NAME
INH
TXD
RXD
FUNCTION
Inhibit Output. Inhibit output is for switching an external voltage regulator if a wake-up signal occurs.
Transmit Data Input
Receive Data Output
4
ERR
Error. Wake-up and power-on indication output; active low in normal operating mode when the bus
has a failure and in low-power modes (wake-up signal or power-on standby).
5
STB
Standby. The digital control signal input (active low) defines, together with input signal on pin EN, the
state of the transceiver (in normal and low-power modes).
6
EN
Enable. The digital control signal input defines, together with input signal on pin
STB
, the state of the
transceiver (in normal and low-power modes).
7
8
9
10
11
12
13
14
WAKE
RTH
RTL
V
CC
CANH
CANL
GND
BATT
Wake-Up. Local wake-up signal input; falling and rising edges are both detected.
Termination Resistor. Termination resistor connection for CANH bus.
Termination Resistor. Termination resistor connection for CANL bus.
Supply Voltage. Bypass to ground with a 0.1μF capacitor.
High-Level Voltage Bus Line
Low-Level Voltage Bus Line
Ground
Battery Supply. Bypass to ground with a 0.1μF capacitor.
相關PDF資料 |
PDF描述 |
|---|---|
| MAX303 | Precision.Dual.High-Speed Analog Switches |
| MAX3031E | ±.15kV ESD-Protected.3.3V Quad RS-422 Transmitters |
| MAX3032E | ±.15kV ESD-Protected.3.3V Quad RS-422 Transmitters |
| MAX3033E | ±.15kV ESD-Protected.3.3V Quad RS-422 Transmitters |
| MAX306 | Precision.16-Channel/Dual 8-Channel.High-Performance.CMOS Analog Multiplexers |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX3023EBC | 制造商:Maxim Integrated Products 功能描述:+1.2V TO 3.6V 0.1MICROAMPS 100MBP - Rail/Tube |
| MAX3023EBC+ | 制造商:Maxim Integrated Products 功能描述:LEVEL TRANSLATOR 12UCSP - Rail/Tube |
| MAX3023EBC+T | 功能描述:轉換 - 電壓電平 1.2-3.6V .1uA 100Mbps RoHS:否 制造商:Micrel 類型:CML/LVDS/LVPECL to LVCMOS/LVTTL 傳播延遲時間:1.9 ns 電源電流:14 mA 電源電壓-最大:3.6 V 電源電壓-最小:3 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:MLF-8 |
| MAX3023EBC+TG47 | 功能描述:轉換 - 電壓電平 1.2-3.6V .1uA 100Mbps RoHS:否 制造商:Micrel 類型:CML/LVDS/LVPECL to LVCMOS/LVTTL 傳播延遲時間:1.9 ns 電源電流:14 mA 電源電壓-最大:3.6 V 電源電壓-最小:3 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:MLF-8 |
| MAX3023EBC-T | 功能描述:轉換 - 電壓電平 RoHS:否 制造商:Micrel 類型:CML/LVDS/LVPECL to LVCMOS/LVTTL 傳播延遲時間:1.9 ns 電源電流:14 mA 電源電壓-最大:3.6 V 電源電壓-最小:3 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:MLF-8 |
發布緊急采購，3分鐘左右您將得到回復。