- 您現在的位置：買賣IC網 > PDF目錄383349 > MAX2825EVKIT (Maxim Integrated Products, Inc.) Evaluation Kits for the MAX2825/MAX2826/MAX2827 PDF資料下載
參數資料
| 型號： | MAX2825EVKIT |
| 廠商： | Maxim Integrated Products, Inc. |
| 英文描述： | Evaluation Kits for the MAX2825/MAX2826/MAX2827 |
| 中文描述： | 評估板的MAX2825/MAX2826/MAX2827 |
| 文件頁數： | 5/12頁 |
| 文件大小： | 1014K |
| 代理商： | MAX2825EVKIT |
E
MAX2825/MAX2826/MAX2827 Evaluation Kits
_______________________________________________________________________________________
5
Windows is a registered trademark of Microsoft.
HP8663A or equivalent low-noise signal source
capable of generating a 20MHz or 40MHz reference
oscillator signal
Two HP8648 or equivalent signal sources capable of
generating 0dBm up to 6GHz
802.11x I/Q waveform generator (optional)
HP8561E or equivalent RF spectrum analyzer with a
minimum frequency range of 100kHz to 6GHz
TDS3012 or equivalent oscilloscope with 200MHz
bandwidth
IBM PC or compatible with Windows95/98/2000/NT
4.0, or later operating system and an available paral-
lel port
Male-to-female 25-pin parallel cable, straight through
Connections and Setup
This section provides step-by-step instructions for get-
ting the EV kit up and running in all modes:
1) Install and run the MAX2825/MAX2826/MAX2827
control software.
2) To control the EV kit through the 3-wire interface,
connect the male-to-female 25-pin parallel cable
between the PC and EV kit.
3) With the power supply turned off, connect a +2.7V
power supply to the header labeled VCC (J13).
Connect the power-supply ground to the header
labeled GND (J12).
4) With the power supply turned off, connect a +5V
power supply to the header labeled +5V (J16), and
a -5V power supply to the header labeled -5V (J14).
Connect the power-supply ground to the header
labeled GND (J21).
5) Connect the low-noise signal source to FREF (J9).
6) Turn on the +5V and -5V power supplies, followed
by the +2.7V power supply. Set the low-noise signal
source to 20MHz and 2dBm. Enable the signal
source. The lock indicator should be green.
Receive Mode
To evaluate the devices in receive mode:
1) Set the RXON jumper (JP22) to the On position and
the TXON jumper (JP21) to the Off position.
2) Connect the RF signal source to either RXRFL
(802.11g, J4) or RXRFH (802.11a, J3). Set the RF fre-
quency to 2437MHz (802.11g) or 5.25GHz (802.11a).
Set the signal power to -100dBm.
3) Set the register setting to the default values listed in
the MAX2825/MAX2826/MAX2827 data sheet. Use
the software to select between 802.11g and 802.11a
modes. In the program, set the frequency to either
2442MHz (802.11g) or 5.255GHz (802.11a). Set the
RX gain to maximum using either the slider bar or
the control bits.
4) Connect the spectrum analyzer to either RXBBI or
RXBBQ. Set the center frequency to 5MHz with a
10MHz span.
5) Turn on the RF signal source. The output at 5MHz
should be approximately -4dBm (802.11g) or -5dBm
(802.11a).
Transmit Mode
To evaluate the devices in transmit mode:
1) Set the TXON jumper (JP21) to the On position and
the RXON jumper (JP22) to the Off position.
2) Connect a 2MHz I/Q signal to TXBBQ and TXBBI.
Set the input amplitude of each channel to
100mV
RMS
.
3) Set the register setting to the default values listed in
the MAX2825/MAX2826/MAX2827 data sheet. Use
the software to select between 802.11g and
802.11a modes. In the program, set the frequency
to either 2437MHz (802.11g) or 5.25GHz (802.11a).
Set the TX gain to maximum using either the slider
bar or the control bits.
4) Connect the spectrum analyzer to either TXRFL
(802.11g, J1) or TXRFH (802.11a, J2).
5) Turn on the baseband signal sources. The output at
RF should be approximately -2dBm (802.11g) or
-4dBm (802.11a).
Layout Considerations
The MAX2825/MAX2826/MAX2827 EV kits can serve as
guides for board layout. Keep PC board trace lengths
as short as possible to minimize parasitic inductance.
Also, keep decoupling capacitors as close to the IC as
possible with a direct connection to the ground plane.
Please refer to the MAX2825/MAX2826/MAX2827 data
sheet for more detailed information. Gerber files for
these EV kits can be requested at www.maxim-ic.com.
相關PDF資料 |
PDF描述 |
|---|---|
| MAX2826EVKIT | Evaluation Kits for the MAX2825/MAX2826/MAX2827 |
| MAX2827EVKIT | Evaluation Kits for the MAX2825/MAX2826/MAX2827 |
| MAX2825 | POT 50K OHM 12MM VERT NO BUSHING |
| MAX2826 | MAX2825/MAX2826/MAX2827 Evaluation Kits |
| MAX2827 | MAX2825/MAX2826/MAX2827 Evaluation Kits |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX2826ETN-D | 功能描述:射頻收發器 RoHS:否 制造商:Atmel 頻率范圍:2322 MHz to 2527 MHz 最大數據速率:2000 Kbps 調制格式:OQPSK 輸出功率:4 dBm 類型: 工作電源電壓:1.8 V to 3.6 V 最大工作溫度:+ 85 C 接口類型:SPI 封裝 / 箱體:QFN-32 封裝:Tray |
| MAX2826ETN-TD | 功能描述:射頻收發器 RoHS:否 制造商:Atmel 頻率范圍:2322 MHz to 2527 MHz 最大數據速率:2000 Kbps 調制格式:OQPSK 輸出功率:4 dBm 類型: 工作電源電壓:1.8 V to 3.6 V 最大工作溫度:+ 85 C 接口類型:SPI 封裝 / 箱體:QFN-32 封裝:Tray |
| MAX2827ETN | 制造商:Maxim Integrated Products 功能描述:- Rail/Tube |
| MAX2827ETN-D | 功能描述:射頻收發器 RoHS:否 制造商:Atmel 頻率范圍:2322 MHz to 2527 MHz 最大數據速率:2000 Kbps 調制格式:OQPSK 輸出功率:4 dBm 類型: 工作電源電壓:1.8 V to 3.6 V 最大工作溫度:+ 85 C 接口類型:SPI 封裝 / 箱體:QFN-32 封裝:Tray |
| MAX2827ETN-TD | 功能描述:射頻收發器 RoHS:否 制造商:Atmel 頻率范圍:2322 MHz to 2527 MHz 最大數據速率:2000 Kbps 調制格式:OQPSK 輸出功率:4 dBm 類型: 工作電源電壓:1.8 V to 3.6 V 最大工作溫度:+ 85 C 接口類型:SPI 封裝 / 箱體:QFN-32 封裝:Tray |
發布緊急采購，3分鐘左右您將得到回復。