- 您現在的位置：買賣IC網 > PDF目錄385523 > MAX2363W (Maxim Integrated Products, Inc.) Evaluation Kits PDF資料下載
參數資料
| 型號： | MAX2363W |
| 廠商： | Maxim Integrated Products, Inc. |
| 英文描述： | Evaluation Kits |
| 中文描述： | 評估板 |
| 文件頁數： | 6/13頁 |
| 文件大小： | 919K |
| 代理商： | MAX2363W |
E
MAX2361/MAX2363W Evaluation Kits
6
_______________________________________________________________________________________
Quick Start
The MAX2361/MAX2363W EV kits are fully assembled
and factory tested. Follow the instructions in the
Connections and Setup
section.
Test Equipment Required
This section lists the recommended test equipment to
verify the operation of the MAX2361/MAX2363/
MAX2365. It is intended as a guide only, and substitu-
tions may be possible.
One TCXO (Temperature-Components Crystal
Oscillator) at 19.68MHz for the PLL reference fre-
quency
An RF spectrum analyzer with optional digital modu-
lation personality (Rohde & Schwarz FSEA30 or
equivalent)
A power supply that can provide 250mA at +3.3V
A power supply that can provide 50mA at +5V
An additional voltage source for control of VGA func-
tions
I/Q arbitrary waveform generator or CDMA generator
(Agilent E4433B or equivalent)
PC (486DX33 or better) with Win95
/98
, Win2000
,
WinNT
4.0 or later operating system and an avail-
able parallel port
INTF2300 interface board (supplied with EV kit)
Connections and Setup
This section provides step-by-step instructions for get-
ting the EV kit up and running in cellular and PCS
CDMA modes.
Cellular CDMA Mode
Perform the following steps to evaluate the MAX2361 in
the cellular CDMA mode:
1) Verify shunts JU1, JU2, and JU6
–
JU10 are in place.
2) Connect the INTF2300 interface cable as shown in
Figure 8.
Note:
Pin 1 of the interface cable corre-
sponds to the red wire. Pin 1 is designated in
silkscreen on each of the PC boards.
3) Connect a +3.0V power supply to VBAT. The
INTF2300 board derives its power from the MAX2361
EV kit.
4) Connect a +5.0V power supply to the header labeled
“
+5V
”
.
5) Connect the TCXO to the REF port.
6) Connect a CDMA baseband signal generator to the
I and Q ports using BNC connectors. Set the modu-
lation to reverse-channel CDMA
7) Install and run Maxim CDMA control software.
Software is also available on the web at
www.maxim-ic.com
. On the IC selection form, click
on the MAX236X control button. Select P4. Click on
register views.
8) With the MAX236X control screen active, set the reg-
isters according to Table 1.
9) Click on the Send Data button for each of the con-
trol registers located at the right of the screen.
There are eight registers that need to be down-
loaded to the IC. The Lock indicator on the screen
(and on the EV board) should be red, indicating
lock.
10) Apply 2.4V to GC via JU4.
11) Connect RFL to the spectrum analyzer. Configure
the spectrum analyzer to measure ACPR for
reverse-channel CDMA. Set the center frequency to
836MHz with a +10dBm reference level.
12) The output power should be about +9dBm after
accounting for cable and connector loss. The ACPR
at ±885kHz offset should be -54dBc, and the ACPR
at ±1.98MHz offset should be -65dBc.
Component Suppliers
MAX2363W Component List
(continued)
Win95
/98
, Win2000
, WinNT
are registered trademarks of
Microsoft Corp.
Note:
Please indicate that you are using the MAX2361/
MAX2363W when contacting these component suppliers.
SUPPLIER
Alpha Industries
AVX
Coilcraft
Murata
Taiyo Yuden
Toko
PHONE
617-935-5150
803-946-0690
847-639-6400
770-436-1300
408-573-4150
708-297-0070
FAX
617-933-2359
803-626-3123
847-639-1469
770-436-3030
408-573-4159
708-699-1194
DESIGNATION
None
QTY
7
DESCRIPTION
Shunts for JU1, JU3, JU6
–
JU10
None
1
MAX2361/MAX2363/MAX2365
data sheet
None
None
None
1
1
1
INTF2300 board
Shunt for JU2
Ribbon cable
相關PDF資料 |
PDF描述 |
|---|---|
| MAX2370_1 | Evaluation Kit |
| MAX2370EVKIT | Evaluation Kit |
| MAX2370 | Complete 450MHz Quadrature Transmitter |
| MAX2370ETM | Complete 450MHz Quadrature Transmitter |
| MAX2371EGC | LNAs with Step Attenuator and VGA |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX2364ECM | 功能描述:射頻發射器 RoHS:否 制造商:Micrel 類型:ASK Transmitter 封裝 / 箱體:SOT-23-6 工作頻率:300 MHz to 450 MHz 封裝:Reel |
| MAX2364ECM-T | 功能描述:射頻發射器 RoHS:否 制造商:Micrel 類型:ASK Transmitter 封裝 / 箱體:SOT-23-6 工作頻率:300 MHz to 450 MHz 封裝:Reel |
| MAX2365ECM | 功能描述:射頻發射器 RoHS:否 制造商:Micrel 類型:ASK Transmitter 封裝 / 箱體:SOT-23-6 工作頻率:300 MHz to 450 MHz 封裝:Reel |
| MAX2365ECM+ | 功能描述:射頻發射器 RoHS:否 制造商:Micrel 類型:ASK Transmitter 封裝 / 箱體:SOT-23-6 工作頻率:300 MHz to 450 MHz 封裝:Reel |
| MAX2365EGM | 功能描述:射頻發射器 RoHS:否 制造商:Micrel 類型:ASK Transmitter 封裝 / 箱體:SOT-23-6 工作頻率:300 MHz to 450 MHz 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。