- 您現在的位置：買賣IC網 > PDF目錄383345 > MAX214EPI (MAXIM INTEGRATED PRODUCTS INC) 5V High-Speed RS-232 Transceivers with 0.1uF Capacitors PDF資料下載
參數資料
| 型號： | MAX214EPI |
| 廠商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分類： | 通用總線功能 |
| 英文描述： | 5V High-Speed RS-232 Transceivers with 0.1uF Capacitors |
| 中文描述： | LINE TRANSCEIVER, PDIP28 |
| 封裝： | PLASTIC, DIP-28 |
| 文件頁數： | 8/12頁 |
| 文件大?。?/td> | 132K |
| 代理商： | MAX214EPI |
M
Programmable DT E/DCE,
+5V RS -232 Transc eiver
8
_______________________________________________________________________________________
which improves noise margins. The polarity of each
receiver’s input threshold is shown in Tables 1a and 1b.
In normal operating mode, receiver inputs are internally
connected to ground with 5k
resistors. So uncon-
nected receivers with positive input thresholds have
high outputs, and those with negative input thresholds
have low outputs.
When shut down, all receivers have positive thresholds.
This allows the receiver inputs to respond to
TTL-/CMOS-logic levels, as well as RS-232 levels. The
guaranteed 0.8V input threshold ensures that receivers
shorted to ground will have a logic 1 output. Also, the
300k
input resistance to ground ensures that a receiv-
er with its input left open will also have a logic 1 output.
The receiver’s 0.5V of hysteresis provides clean output
transitions, even with slow rise-time and fall-time sig-
nals with moderate amounts of noise and ringing. The
receivers have no hysteresis in shutdown mode.
HI-Z Control
The receiver inputs are terminated with 5k
resistors, to
comply with the requirements of EIA/TIA-232E.
However, these internal resistors can be disconnected
by taking the HI-Z control pin to a logic high. This
makes all of the MAX214’s receiver inputs high imped-
ance, and facilitates the transmission of RS-232 data
from a single transmitter to multiple receivers. In this
case, all but one of the receiving ICs should be put into
the high input-impedance state.
S hutdown Control
In shutdown mode, the charge pumps are turned off,
V+ is pulled down to V
CC
, V- is pulled to ground, and
the transmitter outputs are disabled. This reduces sup-
ply current typically to 4μA. The time required to exit
shutdown is about 250μs, as shown in Figure 3.
Receivers
Receiver outputs never go into a high-impedance state;
they are always active, even in shutdown mode (see
Table 2). These awake-in-shutdown receivers are use-
ful for monitoring external activity (for example, on RI),
while maintaining minimal power consumption.
Receivers in shutdown mode are slower (20kbps) than
when not shut down (116kbps), and lack the hysteresis
present in normal operation.
Drivers
The driver outputs are high impedance in shutdown
mode, even when back-driven with voltages up
to ±15V.
__________Applic ations Information
Capac itor S elec tion
The type of capacitor (C1 to C4) used is not critical for
proper operation. The MAX214 requires 1μF capaci-
tors, although in all cases capacitors of up to 10μF
can be used without harm. Ceramic dielectrics are
suggested for the 1μF capacitors.
Table 2. Control Pin Configurations
CONTROL INPUTS
SHUTDOWN
HI-Z
DTE/DCE
RTA, RTB, RTC, RDTC
RRE
0
0
0
Receive Mode/5k
Receive Mode/5k
0
0
1
Transmit Mode
Receive Mode/5k
0
1
0
Receive Mode/HI-Z
Receive Mode/HI-Z
0
1
1
Transmit Mode
Receive Mode/HI-Z
1
0
0
Slow Receive/HI-Z
Slow Receive/HI-Z
1
0
1
Disabled/HI-Z
Slow Receive/HI-Z
1
1
0
Slow Receive/HI-Z
Slow Receive/HI-Z
1
1
1
Disabled/HI-Z
Slow Receive/HI-Z
RS-232 PINS
TRA, TRB, TRC
Transmit Mode
Receive Mode/5k
Transmit Mode
Receive Mode/HI-Z
Disabled/HI-Z
Slow Receive/HI-Z
Disabled/HI-Z
Slow Receive/HI-Z
相關PDF資料 |
PDF描述 |
|---|---|
| MAX212 | 5V High-Speed RS-232 Transceivers with 0.1uF Capacitors |
| MAX214EWI | 5V High-Speed RS-232 Transceivers with 0.1uF Capacitors |
| MAX214 | 16-Bit Buffers/Drivers With 3-State Outputs 48-TVSOP -40 to 85 |
| MAX214CPI | 16-Bit Buffers/Drivers With 3-State Outputs 48-TSSOP -40 to 85 |
| MAX214CWI | 5V High-Speed RS-232 Transceivers with 0.1uF Capacitors |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX214EPI+ | 功能描述:RS-232接口集成電路 Prog DTE/DCE 5V RS232 Transceiver RoHS:否 制造商:Exar 數據速率:52 Mbps 工作電源電壓:5 V 電源電流:300 mA 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:LQFP-100 封裝: |
| MAX214EWI | 功能描述:RS-232接口集成電路 RoHS:否 制造商:Exar 數據速率:52 Mbps 工作電源電壓:5 V 電源電流:300 mA 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:LQFP-100 封裝: |
| MAX214EWI+ | 功能描述:RS-232接口集成電路 Prog DTE/DCE 5V RS232 Transceiver RoHS:否 制造商:Exar 數據速率:52 Mbps 工作電源電壓:5 V 電源電流:300 mA 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:LQFP-100 封裝: |
| MAX214EWI+T | 功能描述:RS-232接口集成電路 Prog DTE/DCE 5V RS232 Transceiver RoHS:否 制造商:Exar 數據速率:52 Mbps 工作電源電壓:5 V 電源電流:300 mA 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:LQFP-100 封裝: |
| MAX214EWI-T | 功能描述:RS-232接口集成電路 RoHS:否 制造商:Exar 數據速率:52 Mbps 工作電源電壓:5 V 電源電流:300 mA 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:LQFP-100 封裝: |
發布緊急采購，3分鐘左右您將得到回復。