- 您現在的位置：買賣IC網 > PDF目錄383345 > MAX2130EUA (MAXIM INTEGRATED PRODUCTS INC) Broadband, Two-Output, Low-Noise Amplifier for TV Tuner Applications PDF資料下載
參數資料
| 型號： | MAX2130EUA |
| 廠商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分類： | 衰減器 |
| 英文描述： | Broadband, Two-Output, Low-Noise Amplifier for TV Tuner Applications |
| 中文描述： | 44 MHz - 878 MHz RF/MICROWAVE WIDE BAND MEDIUM POWER AMPLIFIER |
| 封裝： | UMAX-EP, MO-187, 8 PIN |
| 文件頁數： | 6/8頁 |
| 文件大?。?/td> | 184K |
| 代理商： | MAX2130EUA |
M
Broadband, Two-Output, Low-Noise
Amplifier for TV Tuner Applications
6
_______________________________________________________________________________________
Detailed Description
The MAX2130 is a broadband, high-gain, low-distortion
low-noise amplifier (LNA) with two outputs intended for
operation over the 44MHz to 878MHz frequency range.
The device operates from a +5V supply and features
externally adjustable bias control circuitry that allows
minimum linearity requirements to be met while reduc-
ing current consumption.
Input
The IN port is a broadband 75
input that provides a
guaranteed minimum input return loss of 7.4dB (allow-
ing for 2:1 VSWR at output) across the 44MHz to
878MHz frequency range. AC-couple the IN port with a
0.1μF DC-blocking capacitor.
Outputs
The OUT1 port is a broadband, 75
, open-collector
output for the LNA. It requires a pullup inductor to V
CC
for proper biasing, as well as a 0.1μF DC-blocking
capacitor. See the
Applications Information
section for
proper inductor selection.
The OUT2 port is a broadband, 75
output for the loop-
out amplifier. The loop-out amplifier is internally biased
and does not require a pullup inductor. AC-couple the
OUT2 port with a 0.1μF DC-blocking capacitor.
Bias Circuitry
The linearity and supply current for both amplifiers are
externally programmable with a single resistor, R
BIAS
,
from BIAS to GND. A nominal resistor value of 15k
sets an input IP3 of +17.5dBm, an input IP2 of
+27dBm, and a supply current of 93mA. Decrease the
resistor value to improve linearity at the cost of
increased supply current. Increase the resistor value to
decrease supply current and degrade linearity. Use
resistor values greater than 10k
. Gain is not signifi-
cantly affected by the R
BIAS
value.
Applications Information
Inductor Selection
The OUT1 port of the LNA requires a pull-up inductor to
V
CC
for proper biasing. The exact value of the inductor
is not important as long as it has broadband imped-
ance >150
(<500
) at 10MHz across the 44MHz to
878MHz frequency band. Table 1 is a list of recom-
mended inductors.
Pin Description
PIN
NAME
FUNCTION
1
V
CC
Supply Voltage Input. Bypass with a 1000pF capacitor in parallel with a 47pF capacitor as close to
the pin as possible. (See
Typical Application Circuit
.)
2
IN
Broadband Input to Low-Noise Amplifier and Loop-Out Amplifier. Internally matched to 75
.
Requires 0.1
μ
F DC-blocking capacitor. (See
Typical Application Circuit
.)
3
BIAS
Bias-Setting Resistor Connection. Connect a resistor, R
BIAS
, from BIAS to GND to set the linearity
and supply current of the LNA and the loop-out amplifier.
4, 6, 7, EP
GND
Ground. Connect to ground plane with a low-inductance connection. Solder exposed paddle evenly
to the board groundplane.
5
OUT2
Output of Loop-Out Amplifier. Requires a 0.1
μ
F DC-blocking capacitor. (See
Typical Application
Circuit.
)
8
OUT1
Open-Collector Output of Low-Noise Amplifier. Requires a pullup inductor to V
CC
, as well as a 0.1
μ
F
DC-blocking capacitor. (See
Typical Application Circuit
.)
PART NUMBER
BLM11A221S
BLM11A471SG
BLM10A221SG
MANUFACTURER
Murata
Murata
Murata
BLM21A331SG
Murata
Table 1. OUT1 Pullup Inductor
Recommended Components
相關PDF資料 |
PDF描述 |
|---|---|
| MAX213EWI | 5V High-Speed RS-232 Transceivers with 0.1uF Capacitors |
| MAX213 | 5V High-Speed RS-232 Transceivers with 0.1uF Capacitors |
| MAX2130 | Broadband, Two-Output, Low-Noise Amplifier for TV Tuner Applications |
| MAX213CAI | 5V High-Speed RS-232 Transceivers with 0.1uF Capacitors |
| MAX213CWI | 5V High-Speed RS-232 Transceivers with 0.1uF Capacitors |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX2130EUA+ | 功能描述:射頻放大器 Broadband Two-Output Low-Noise Amplifier RoHS:否 制造商:Skyworks Solutions, Inc. 類型:Low Noise Amplifier 工作頻率:2.3 GHz to 2.8 GHz P1dB:18.5 dBm 輸出截獲點:37.5 dBm 功率增益類型:32 dB 噪聲系數:0.85 dB 工作電源電壓:5 V 電源電流:125 mA 測試頻率:2.6 GHz 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-16 封裝:Reel |
| MAX2130EUA+T | 功能描述:射頻放大器 Broadband Two-Output Low-Noise Amplifier RoHS:否 制造商:Skyworks Solutions, Inc. 類型:Low Noise Amplifier 工作頻率:2.3 GHz to 2.8 GHz P1dB:18.5 dBm 輸出截獲點:37.5 dBm 功率增益類型:32 dB 噪聲系數:0.85 dB 工作電源電壓:5 V 電源電流:125 mA 測試頻率:2.6 GHz 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-16 封裝:Reel |
| MAX2130EUA-T | 功能描述:射頻放大器 Broadband Two-Output Low-Noise Amplifier RoHS:否 制造商:Skyworks Solutions, Inc. 類型:Low Noise Amplifier 工作頻率:2.3 GHz to 2.8 GHz P1dB:18.5 dBm 輸出截獲點:37.5 dBm 功率增益類型:32 dB 噪聲系數:0.85 dB 工作電源電壓:5 V 電源電流:125 mA 測試頻率:2.6 GHz 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-16 封裝:Reel |
| MAX2130EVKIT | 功能描述:放大器 IC 開發工具 MAX2130 Eval Kit RoHS:否 制造商:International Rectifier 產品:Demonstration Boards 類型:Power Amplifiers 工具用于評估:IR4302 工作電源電壓:13 V to 23 V |
| MAX2135A | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:PLASTIC ENCAPSULATED DEVICES |
發布緊急采購，3分鐘左右您將得到回復。