- 您現在的位置：買賣IC網 > PDF目錄385523 > MAX2059ETL-T (MAXIM INTEGRATED PRODUCTS INC) 1700MHz to 2200MHz High-Linearity, SPI-Controlled DVGA with Integrated Loopback Mixer PDF資料下載
參數資料
| 型號： | MAX2059ETL-T |
| 廠商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分類： | 無繩電話/電話 |
| 英文描述： | 1700MHz to 2200MHz High-Linearity, SPI-Controlled DVGA with Integrated Loopback Mixer |
| 中文描述： | TELECOM, CELLULAR, RF AND BASEBAND CIRCUIT, QCC40 |
| 封裝： | 6 X 6 MM, 0.80 MM HEIGHT, TQFN-40 |
| 文件頁數： | 11/14頁 |
| 文件大?。?/td> | 801K |
| 代理商： | MAX2059ETL-T |
M
1700MHz to 2200MHz High-Linearity,
SPI-Controlled DVGA with Integrated Loopback Mixer
______________________________________________________________________________________
11
Detailed Description
The MAX2059 high-linearity DVGA consists of two 5-bit
digital attenuators, a fixed-gain two-stage driver amplifi-
er, a loopback mixer, and a serial interface to control
the attenuators. This high level of component integra-
tion makes the MAX2059 ideal for base-station trans-
mitter applications. The MAX2059 is designed to
operate in the 1700MHz to 2200MHz frequency range.
The overall cascaded performance of the MAX2059
produces a typical 10.9dB gain, a +31.8dBm OIP3, an
18.4dBm OP1dB, and a total 56dB gain-control range.
5-Bit Attenuators
The MAX2059 integrates two 5-bit digital attenuators to
achieve a high dynamic range. Each attenuator is pro-
grammed with a 3-wire SPI interface, with a total effec-
tive range of 28dB and step size of 1dB. See the
Applications Information
section and Table 1 for attenu-
ator programming details. The attenuators can be used
for both static and dynamic power control.
Driver Amplifier
The MAX2059 includes a two-stage medium power
amplifier with a fixed 18.5dB gain. The driver amplifier
circuit is optimized for high linearity and medium output
power capability for the 1800MHz to 2000MHz frequen-
cy range. The driver amplifier is intended to amplify a
modulated signal and drive a high-power amplifier in
base-station transmitters. In a typical application, the
driver amplifier is cascaded in between the two digital
attenuators. See the
Typical Application Circuit.
The two-stage amplifier stage can be disabled for
applications where only the digital attenuators and/or
loopback mixer are used. To disable the two-stage
amplifier, ground or leave unconnected the amplifier
supplies VCCBIAS2, VCCAMP, VCCBIAS1, and also
the inputs for setting the amplifier bias currents RSET1,
RSET2. This reduces the supply current by approxi-
mately 187mA under typical conditions.
Loopback Mixer
The MAX2059 loopback mixer uses a double-balanced
active architecture designed to operate with a
1700MHz to 2200MHz RF frequency range, and a
40MHz to 100MHz LO frequency range. The RF port of
the mixer is connected internally (with an on-chip
switch) to the input of the first attenuator stage. The
mixer’s IF port is matched for a single-ended 50
Ω
impedance, while the LO port requires a differential
input impedance of 100
Ω
.
The loopback mixer facilitates a self-diagnostic mode
for cellular transceivers, whereby the Tx band signal at
the input of the mixer can be translated up or down to
the corresponding Rx band. This translated signal can
then be fed back to the radio’s receiver for complete
Tx/Rx loop diagnostics. The loopback mixer is enabled
and disabled with LB_EN. Set LB_EN to a logic-low 0 to
enable the mixer, set LB_EN to a logic-high 1 to disable
the mixer.
The MAX2059 loopback mixer accepts a nominal -6dBm
LO input power and exhibits a -12.6dBm output power
and an output IP3 of 6.2dBm (P
IN
= +5dBm).
Applications Information
SPI Interface and Attenuator Settings
The two 5-bit attenuators are programmed with the 3-
wire SPI/MICROWIRE-compatible serial interface using
10-bit words. Bit 9 of the 10-bit data is shifted in first,
along with all remaining data bits, on the rising edge of
the clock regardless of
CS
being high or low. Once all
the data bits are shifted in, all will be sent to the attenua-
tors on the rising edge of
CS
, thus changing the attenua-
tion state. For standard SPI operation, pull
CS
low for the
ATTENUATOR A (5 MSBs)
Bit 9 = 16dB step
Bit 8 = 8dB step
Bit 7 = 4dB step
Bit 6 = 2dB step
Bit 5 = 1dB step
ATTENUATOR B (5 LSBs)
Bit 4 = 16dB step
Bit 3 = 8dB step
Bit 2 = 4dB step
Bit 1 = 2dB step
Bit 0 = 1dB step
NOTES:
DATA ENTERED ON CLOCK RISING EDGE.
ATTENUATOR STATE CHANGE ON CS RISING EDGE.
MSB
DATA
CLOCK
CS
BIT 9
BIT 8
BIT 1
BIT 0
LSB
t
CS
t
CH
t
CW
t
EWN
t
ES
t
EW
Table 1. Attenuator Programming
Figure 1. SPI Timing Diagram
Note:
Due to finite circuit isolation, the total effective range of
each attenuator is limited to 28dB.
相關PDF資料 |
PDF描述 |
|---|---|
| MAX2041_1 | Evaluation Kit |
| MAX2041EVKIT | Evaluation Kit |
| MAX2041 | High-Linearity, 1700MHz to 3000MHz Upconversion / Downconversion Mixer with LO Buffer / Switch |
| MAX2041ETP | High-Linearity, 1700MHz to 3000MHz Upconversion / Downconversion Mixer with LO Buffer / Switch |
| MAX2041ETP-T | High-Linearity, 1700MHz to 3000MHz Upconversion / Downconversion Mixer with LO Buffer / Switch |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX2059EVKIT | 功能描述:射頻放大器 1700 to 2200MHz High-Linearity SPI-Controlled DVGA w. Integrated Loopback Mixer RoHS:否 制造商:Skyworks Solutions, Inc. 類型:Low Noise Amplifier 工作頻率:2.3 GHz to 2.8 GHz P1dB:18.5 dBm 輸出截獲點:37.5 dBm 功率增益類型:32 dB 噪聲系數:0.85 dB 工作電源電壓:5 V 電源電流:125 mA 測試頻率:2.6 GHz 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-16 封裝:Reel |
| MAX2059EVKIT+ | 功能描述:射頻放大器 1700MHz to 2200MHz High-Linearity SPI-Controlled DVGA with Integrated Loopback Mixer RoHS:否 制造商:Skyworks Solutions, Inc. 類型:Low Noise Amplifier 工作頻率:2.3 GHz to 2.8 GHz P1dB:18.5 dBm 輸出截獲點:37.5 dBm 功率增益類型:32 dB 噪聲系數:0.85 dB 工作電源電壓:5 V 電源電流:125 mA 測試頻率:2.6 GHz 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-16 封裝:Reel |
| MAX205CPG | 功能描述:RS-232接口集成電路 RoHS:否 制造商:Exar 數據速率:52 Mbps 工作電源電壓:5 V 電源電流:300 mA 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:LQFP-100 封裝: |
| MAX205CPG+G36 | 功能描述:RS-232接口集成電路 5V RS232 Transceiver w/0.1uF External Cap RoHS:否 制造商:Exar 數據速率:52 Mbps 工作電源電壓:5 V 電源電流:300 mA 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:LQFP-100 封裝: |
| MAX205CPG-G36 | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:5V, RS-232 Transceivers with 0.1muF External Capacitors |
發布緊急采購，3分鐘左右您將得到回復。