參數資料
型號: MAX2034CTM-T
廠商: MAXIM INTEGRATED PRODUCTS INC
元件分類: 消費家電
英文描述: Quad-Channel, Ultra-Low-Noise Amplifier with Digitally Programmable Input Impedance
中文描述: SPECIALTY CONSUMER CIRCUIT, QCC48
封裝: 7 X 7 MM, 0.80 MM HEIGHT, MO-220, TQFN-48
文件頁數: 8/13頁
文件大?。?/td> 356K
代理商: MAX2034CTM-T
M
Digitally Programmable Input Impedance
The MAX2034 features an on-chip digitally programma-
ble input impedance, which makes the part compatible
with a variety of source impedances ranging from 50
to 1k
. The input impedance can be programmed for
50
, 100
, 200
, or 1k
through the digital inputs D2,
D1, and D0. See Table 1 for programming details. In
addition to these fixed values, virtually any other input
impedance can be supported by using an off-chip
external feedback resistor, R
F
. To utilize this feature, set
D2, D1, and D0 to any of the four external resistor-con-
trolled states shown in Table 1. The value of the off-chip
feedback resistor can be determined by using the fol-
lowing relationship:
R
F
= (1 + (A / 2)) x R
S
where R
S
is the source impedance, and A is the gain of
the amplifier (A = 9) defined with a differential output.
Noise Figure
The MAX2034 is designed to provide maximum input
sensitivity with its exceptionally low noise figure. The
input active devices are selected for very low equiva-
lent input noise voltage and current, and they have
been optimized for source impedances from 50
to
1000
. Additionally, the noise contribution of the
matching resistor is effectively divided by 1 + (A / 2).
Using this scheme, typical noise figure of the amplifier
is approximately 2.2dB for R
IN
= R
S
= 200
. Table 2
illustrates the noise figure for other input impedances.
Input Clamp
The MAX2034 includes configurable integrated input-
clamping diodes. The diodes are clamped to ground at
±275mV. The input-clamping diodes can be used to
prevent large transmit signals from overdriving the inputs
of the amplifiers. Overdriving the inputs could possibly
place charge on the input-coupling capacitor, causing
longer transmit overload recovery times. Input signals
are AC-coupled to the single-ended inputs IN1–IN4, but
are clamped with the INC1–INC4 inputs. See the
Typical
Application Circuit
. If external clamping devices are pre-
ferred, simply leave INC1–INC4 unconnected.
Quad-Channel, Ultra-Low-Noise Amplifier with
Digitally Programmable Input Impedance
8
_______________________________________________________________________________________
Functional Diagram
D2/D1/D0
ZF1
PD
IN1
INC1
INB1
OUT1-
OUT1+
ZF2
IN2
INC2
INB2
OUT2-
OUT2+
ZF3
IN3
INC3
INB3
OUT3-
OUT3+
ZF4
IN4
INC4
INB4
OUT4-
OUT4+
MAX2034
Table 2. Noise Figure vs. Source and
Input Impedances
Rs (
)
50
100
200
1000
R
IN
(
)
50
100
200
1000
NF (dB)
4.1
2.9
2.2
1.4
相關PDF資料
PDF描述
MAX2039 Evaluation Kit
MAX2039_1 Evaluation Kit
MAX2039EVKIT Evaluation Kit
MAX2043ETX 1700MHz to 3000MHz High-Linearity, Low LO Leakage Base-Station Rx/Tx Mixer
MAX2043ETX-T 1700MHz to 3000MHz High-Linearity, Low LO Leakage Base-Station Rx/Tx Mixer
相關代理商/技術參數
參數描述
MAX2035 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:Ultrasound Variable-Gain Amplifier
MAX2035_09 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:Ultrasound Variable-Gain Amplifier
MAX2035CCQ 功能描述:儀表放大器 Ultrasound Variable Gain Amplifier RoHS:否 制造商:Texas Instruments 通道數量: 輸入補償電壓:150 V 可用增益調整: 最大輸入電阻:10 kOhms 共模抑制比(最小值):88 dB 工作電源電壓:2.7 V to 36 V 電源電流:200 uA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 封裝 / 箱體:MSOP-8 封裝:Bulk
MAX2035CCQ+ 功能描述:儀表放大器 Ultrasound Variable Gain Amplifier RoHS:否 制造商:Texas Instruments 通道數量: 輸入補償電壓:150 V 可用增益調整: 最大輸入電阻:10 kOhms 共模抑制比(最小值):88 dB 工作電源電壓:2.7 V to 36 V 電源電流:200 uA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 封裝 / 箱體:MSOP-8 封裝:Bulk
MAX2035CCQ+D 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:Ultrasound Variable-Gain Amplifier