參數資料
型號： MAX198
廠商： Maxim Integrated Products, Inc.
英文描述： Multirange, Single +5V, 12-Bit DAS with 12-Bit Bus Interface(6通道,100ksps,并行,12位A/D轉換器)
中文描述： 6通道、多量程、5V、12位DAS，帶有12位總線接口和故障保護
文件頁數： 13/16頁
文件大小： 165K
代理商： MAX198
__________Applic ations Information
Power-On Reset
At power-up, the internal power-on reset circuitry sets
INT high and puts the device in normal operation/exter-
nal clock mode. This state is selected to keep the inter-
nal clock from loading the external clock driver when
the part is used in external clock mode.
Internal or External Referenc e
The MAX196/MAX198 can operate with either an inter-
nal or external reference. An external reference can be
connected to either the REF pin or the REFADJ pin
(Figure 9).
To use the REF input directly, disable the internal buffer
by tying REFADJ to V
DD
. Using the REFADJ input elimi-
nates the need to buffer the reference externally. When
the reference is applied at REFADJ , bypass REFADJ with
a 0.01μF capacitor to AGND.
The REFADJ internal buffer gain is trimmed to 1.6384 to
provide 4.096V at the REF pin from a 2.5V reference.
Internal Reference
The internally trimmed 2.50V reference is gained
through the REFADJ buffer to provide 4.096V at REF.
Bypass the REF pin with a 4.7μF capacitor to AGND
and the REFADJ pin with a 0.01μF capacitor to AGND.
The internal reference voltage is adjustable to ±1.5%
(±65 LSBs) with the reference-adjust circuit of Figure 1.
External Reference
At REF and REFADJ , the input impedance is a mini-
mum of 10k
for DC currents. During conversions, an
external reference at REF must be able to deliver
400μA DC load currents, and must have an output
impedance of 10
or less. If the reference has higher
output impedance or is noisy, bypass it close to the
REF pin with a 4.7μF capacitor to AGND.
With an external reference voltage of less than 4.096V
at the REF pin or less than 2.5V at the REFADJ pin, the
increase in the ratio of the RMS noise to the LSB value
(FS / 4096) results in performance degradation (loss of
effective bits).
Power-Down Mode
To save power, you can put the converter into low-
current shutdown mode between conversions. Two
programmable power-down modes are available:
STBYPD and FULLPD. Select STBYPD or FULLPD by
programming PD0 and PD1 in the input control byte.
When power-down is asserted, it becomes effective
only after the end of conversion. In all power-down
modes, the interface remains active and conversion
M
Multirange, S ingle +5V, 12-Bit DAS
with 12-Bit Bus Interfac e
______________________________________________________________________________________
13
REF
10k
2.5V
26
4.096V
4.7
μ
F
C
REF
0.01
μ
F
25
REFADJ
A
V
= 1.638
MAX196
MAX198
Figure 9a. Internal Reference
REF
10k
2.5V
26
4.7
μ
F
C
REF
2.5V
25
REFADJ
A
V
= 1.638
0.01
μ
F
MAX196
MAX198
4.096V
Figure 9c. The external reference overdrives the internal refer-
ence.
REF
V
DD
10k
2.5V
26
4.096V
4.7
μ
F
C
REF
25
REFADJ
A
V
= 1.638
MAX196
MAX198
Figure 9b. External Reference, Reference at REF
相關PDF資料
PDF描述
MAX198ACAI Multirange, Single %V, 12-Bit DAS with 12-Bit Bus Interface
MAX198ACNI Multirange, Single %V, 12-Bit DAS with 12-Bit Bus Interface
MAX198ACWI Multirange, Single %V, 12-Bit DAS with 12-Bit Bus Interface
MAX198AENI Fixed-Point Digital Signal Processor 532-FCBGA
MAX198AEWI Multirange, Single %V, 12-Bit DAS with 12-Bit Bus Interface
相關代理商/技術參數
參數描述
MAX1980EGP 功能描述:DC/DC 開關控制器 RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK
MAX1980EGP-T 功能描述:DC/DC 開關控制器 RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK
MAX1980ETP 功能描述:DC/DC 開關控制器 RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK
MAX1980ETP+ 功能描述:DC/DC 開關控制器 PWM Slave Controller w/Driver Disable RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK
MAX1980ETP+T 功能描述:DC/DC 開關控制器 PWM Slave Controller w/Driver Disable RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*