- 您現在的位置：買賣IC網 > PDF目錄383334 > MAX1977 (Maxim Integrated Products, Inc.) High-Efficiency, Quad Output, Main Power- Supply Controllers for Notebook Computers PDF資料下載
參數資料
| 型號： | MAX1977 |
| 廠商： | Maxim Integrated Products, Inc. |
| 英文描述： | High-Efficiency, Quad Output, Main Power- Supply Controllers for Notebook Computers |
| 中文描述： | 高效率、四路輸出、主電源控制器，用于筆記本電腦 |
| 文件頁數： | 22/32頁 |
| 文件大小： | 497K |
| 代理商： | MAX1977 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁當前第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁
M
High-Effic ienc y, Quad Output, Main Power-
S upply Controllers for Notebook Computers
22
______________________________________________________________________________________
Adaptive dead-time circuits monitor the DL_ and DH_
drivers and prevent either FET from turning on until the
other is fully off. This algorithm allows operation without
shoot-through with a wide range of MOSFETs, minimiz-
ing delays and maintaining efficiency. There must be
low-resistance, low-inductance paths from the gate dri-
vers to the MOSFET gates for the adaptive dead-time cir-
cuit to work properly. Otherwise, the sense circuitry
interprets the MOSFET gate as “off” when there is actual-
ly charge left on the gate. Use very short, wide traces
measuring 10 to 20 squares (50mils to 100mils wide if
the MOSFET is 1in from the device).
POR, UV LO, and Internal Digital
S oft-S tart
Power-on reset (POR) occurs when V+ rises above
approximately 1V, resetting the undervoltage, over-
voltage, and thermal-shutdown fault latches. LDO5
undervoltage lockout (UVLO) circuitry inhibits switching
when LDO5 is below 4V. DL_ is low if
PRO
is disabled;
DL_ is high if
PRO
is enabled. The output voltages
begin to ramp up as LDO5 rises above 4V. The internal
digital soft-start timer begins to ramp up the maximum
allowed current limit during startup. The 1.7ms ramp
occurs in five steps: 20%, 40%, 60%, 80%, and 100%.
Power-Good Output (PGOOD)
The PGOOD comparator continuously monitors both out-
put voltages for undervoltage conditions. PGOOD is
actively held low in shutdown, standby, and soft-start.
PGOOD releases and digital soft-start terminates when
both outputs reach the error-comparator threshold.
PGOOD goes low if either output turns off or is 10%
below its nominal regulation point. PGOOD is a true
open-drain output. Note that PGOOD is independent of
the state of
PRO
.
Fault Protec tion
The MAX1777/MAX1977/MAX1999 provide over/under-
voltage fault protection. Drive
PRO
low to activate fault
protection. Drive
PRO
high to disable fault protection.
Once activated, the devices continuously monitor for
both undervoltage and overvoltage conditions.
Overvoltage Protection
When the output voltage is 11% above the set voltage,
the overvoltage fault protection activates. The synchro-
nous rectifier turns on 100% and the high-side MOSFET
turns off. This rapidly discharges the output capacitors,
decreasing the output voltage. The output voltage may
dip below ground. For loads that cannot tolerate a neg-
ative voltage, place a power Schottky diode across the
output to act as a reverse-polarity clamp. In practical
applications, there is a fuse between the power source
(battery) and the external high-side switches. If the
overvoltage condition is caused by a short in the high-
side switch, turning the synchronous rectifier on 100%
creates an electrical short between the battery and
GND, blowing the fuse and disconnecting the battery
from the output. Once an overvoltage fault condition is
set, it can only be reset by toggling
SHDN
, ON_, or
cycling V+ (POR).
Undervoltage Protection
When the output voltage is 30% below the set voltage
for over 22ms (undervoltage shutdown blanking time),
the undervoltage fault protection activates. Both SMPSs
stop switching. The two outputs start to discharge (see
the
Discharge Mode (Soft-Stop)
section). When the out-
put voltage drops to 0.3V, the synchronous rectifiers
turn on, clamping the outputs to GND. Toggle
SHDN
,
ON_, or cycle V+ (POR) to clear the undervoltage fault
latch.
Thermal Protection
The MAX1777/MAX1977/MAX1999 have thermal shut-
down to protect the devices from overheating. Thermal
shutdown occurs when the die temperature exceeds
+160°C. All internal circuitry shuts down during thermal
shutdown. The MAX1777/MAX1977/MAX1999 may trig-
ger thermal shutdown if LDO_ is not bootstrapped from
OUT_ while applying a high input voltage on V+ and
drawing the maximum current (including short circuit)
from LDO_. Even if LDO_ is bootstrapped from OUT_,
overloading the LDO_ causes large power dissipation
on the bootstrap switches, which may result in thermal
shutdown. Cycling
SHDN
, ON3, or ON5, or a V+ (POR)
ends the thermal shutdown state.
Disc harge Mode (S oft-S top)
When
PRO
is low, and a transition to standby or shut-
down mode occurs, or the output undervoltage fault
latch is set, the outputs discharge to GND through an
internal 12
switch, until the output voltages decrease
to 0.3V. The reference remains active to provide an
accurate threshold and to provide overvoltage protec-
tion. When both SMPS outputs discharge to 0.3V, the
DL_ synchronous rectifier drivers are forced high. The
synchronous rectifier drivers clamp the SMPS outputs
to GND. When
PRO
is high, the SMPS outputs do not
discharge, and the DL_ synchronous rectifier drivers
remain low.
S hutdown Mode
Drive
SHDN
below the precise
SHDN
input falling-edge
trip level to place the MAX1777/MAX1977/MAX1999 in
its low-power shutdown state. The MAX1777/MAX1977/
MAX1999 consume only 6μA of quiescent current while
相關PDF資料 |
PDF描述 |
|---|---|
| MAX1999 | High-Efficiency, Quad Output, Main Power- Supply Controllers for Notebook Computers |
| MAX1977EEI | High-Efficiency, Quad Output, Main Power- Supply Controllers for Notebook Computers |
| MAX1999EEI | High-Efficiency, Quad Output, Main Power- Supply Controllers for Notebook Computers |
| MAX1778 | 32-Bit Digital Signal Controller with ROM 100-LQFP -40 to 85 |
| MAX1880 | Quad-Output TFT LCD DC-DC Converters with Buffer |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX1977EEI | 功能描述:DC/DC 開關控制器 RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK |
| MAX1977EEI+ | 功能描述:DC/DC 開關控制器 Quad Out Main Power Supply Controller RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK |
| MAX1977EEI+T | 功能描述:DC/DC 開關控制器 Quad Out Main Power Supply Controller RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK |
| MAX1977EEI-T | 功能描述:DC/DC 開關控制器 RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK |
| MAX1977EEI-TG068 | 制造商:Rochester Electronics LLC 功能描述: 制造商:Maxim Integrated Products 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。