- 您現在的位置：買賣IC網 > PDF目錄383342 > MAX196BMYI (MAXIM INTEGRATED PRODUCTS INC) Multirange, Single %V, 12-Bit DAS with 12-Bit Bus Interface PDF資料下載
參數資料
| 型號： | MAX196BMYI |
| 廠商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分類： | 模擬信號調理 |
| 英文描述： | Multirange, Single %V, 12-Bit DAS with 12-Bit Bus Interface |
| 中文描述： | SPECIALTY ANALOG CIRCUIT, CDIP28 |
| 封裝： | 0.600 INCH, SIDE BRAZED, CERAMIC, DIP-28 |
| 文件頁數： | 13/16頁 |
| 文件大小： | 165K |
| 代理商： | MAX196BMYI |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁當前第13頁第14頁第15頁第16頁
__________Applic ations Information
Power-On Reset
At power-up, the internal power-on reset circuitry sets
INT high and puts the device in normal operation/exter-
nal clock mode. This state is selected to keep the inter-
nal clock from loading the external clock driver when
the part is used in external clock mode.
Internal or External Referenc e
The MAX196/MAX198 can operate with either an inter-
nal or external reference. An external reference can be
connected to either the REF pin or the REFADJ pin
(Figure 9).
To use the REF input directly, disable the internal buffer
by tying REFADJ to V
DD
. Using the REFADJ input elimi-
nates the need to buffer the reference externally. When
the reference is applied at REFADJ , bypass REFADJ with
a 0.01μF capacitor to AGND.
The REFADJ internal buffer gain is trimmed to 1.6384 to
provide 4.096V at the REF pin from a 2.5V reference.
Internal Reference
The internally trimmed 2.50V reference is gained
through the REFADJ buffer to provide 4.096V at REF.
Bypass the REF pin with a 4.7μF capacitor to AGND
and the REFADJ pin with a 0.01μF capacitor to AGND.
The internal reference voltage is adjustable to ±1.5%
(±65 LSBs) with the reference-adjust circuit of Figure 1.
External Reference
At REF and REFADJ , the input impedance is a mini-
mum of 10k
for DC currents. During conversions, an
external reference at REF must be able to deliver
400μA DC load currents, and must have an output
impedance of 10
or less. If the reference has higher
output impedance or is noisy, bypass it close to the
REF pin with a 4.7μF capacitor to AGND.
With an external reference voltage of less than 4.096V
at the REF pin or less than 2.5V at the REFADJ pin, the
increase in the ratio of the RMS noise to the LSB value
(FS / 4096) results in performance degradation (loss of
effective bits).
Power-Down Mode
To save power, you can put the converter into low-
current shutdown mode between conversions. Two
programmable power-down modes are available:
STBYPD and FULLPD. Select STBYPD or FULLPD by
programming PD0 and PD1 in the input control byte.
When power-down is asserted, it becomes effective
only after the end of conversion. In all power-down
modes, the interface remains active and conversion
M
Multirange, S ingle +5V, 12-Bit DAS
with 12-Bit Bus Interfac e
______________________________________________________________________________________
13
REF
10k
2.5V
26
4.096V
4.7
μ
F
C
REF
0.01
μ
F
25
REFADJ
A
V
= 1.638
MAX196
MAX198
Figure 9a. Internal Reference
REF
10k
2.5V
26
4.7
μ
F
C
REF
2.5V
25
REFADJ
A
V
= 1.638
0.01
μ
F
MAX196
MAX198
4.096V
Figure 9c. The external reference overdrives the internal refer-
ence.
REF
V
DD
10k
2.5V
26
4.096V
4.7
μ
F
C
REF
25
REFADJ
A
V
= 1.638
MAX196
MAX198
Figure 9b. External Reference, Reference at REF
相關PDF資料 |
PDF描述 |
|---|---|
| MAX198BMYI | Multirange, Single %V, 12-Bit DAS with 12-Bit Bus Interface |
| MAX1961EEP | 2.35V to 5.5V, 0.5% Accurate, 1MHz PWM Step-Down Controllers with Voltage Margining |
| MAX1960 | 2.35V to 5.5V, 0.5% Accurate, 1MHz PWM Step-Down Controllers with Voltage Margining |
| MAX1960EEP | 2.35V to 5.5V, 0.5% Accurate, 1MHz PWM Step-Down Controllers with Voltage Margining |
| MAX1961 | 2.35V to 5.5V, 0.5% Accurate, 1MHz PWM Step-Down Controllers with Voltage Margining |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX196EVKIT-DIP | 功能描述:數據轉換 IC 開發工具 Programmers, Development Systems RoHS:否 制造商:Texas Instruments 產品:Demonstration Kits 類型:ADC 工具用于評估:ADS130E08 接口類型:SPI 工作電源電壓:- 6 V to + 6 V |
| MAX19700ETM | 功能描述:ADC / DAC多通道 RoHS:否 制造商:Texas Instruments 轉換速率: 分辨率:8 bit 接口類型:SPI 電壓參考: 電源電壓-最大:3.6 V 電源電壓-最小:2 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-40 |
| MAX19700ETM+ | 功能描述:ADC / DAC多通道 7.5Msps CODEC/AFE 1.8/2.7-3.3V RoHS:否 制造商:Texas Instruments 轉換速率: 分辨率:8 bit 接口類型:SPI 電壓參考: 電源電壓-最大:3.6 V 電源電壓-最小:2 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-40 |
| MAX19700ETM+T | 功能描述:ADC / DAC多通道 7.5Msps CODEC/AFE 1.8/2.7-3.3V RoHS:否 制造商:Texas Instruments 轉換速率: 分辨率:8 bit 接口類型:SPI 電壓參考: 電源電壓-最大:3.6 V 電源電壓-最小:2 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-40 |
| MAX19700ETM-T | 功能描述:ADC / DAC多通道 RoHS:否 制造商:Texas Instruments 轉換速率: 分辨率:8 bit 接口類型:SPI 電壓參考: 電源電壓-最大:3.6 V 電源電壓-最小:2 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-40 |
發布緊急采購，3分鐘左右您將得到回復。