- 您現在的位置：買賣IC網 > PDF目錄383342 > MAX196BEAI (MAXIM INTEGRATED PRODUCTS INC) CONNECTOR PDF資料下載
參數資料
| 型號： | MAX196BEAI |
| 廠商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分類： | 模擬信號調理 |
| 英文描述： | CONNECTOR |
| 中文描述： | SPECIALTY ANALOG CIRCUIT, PDSO28 |
| 封裝： | 0.200 INCH, 0.65 MM PITCH, SSOP-28 |
| 文件頁數： | 10/16頁 |
| 文件大?。?/td> | 165K |
| 代理商： | MAX196BEAI |
M
Input Format
The control byte is latched into the device, on pins
D7–D0, during a write cycle. Table 2 shows the control-
byte format.
Output Data Format
The output data format is binary in unipolar mode and
twos-complement binary in bipolar mode. When reading
the output data, CS and RD must be low.
How to S tart a Conversion
Conversions are initiated with a write operation, which
selects the mux channel and configures the MAX196/
MAX198 for either a unipolar or bipolar input range. A
write pulse (WR + CS) can either start an acquisition inter-
val or initiate a combined acquisition plus conversion. The
sampling interval occurs at the end of the acquisition
interval. The ACQMOD bit in the input control byte offers
two options for acquiring the signal: internal or external.
The conversion period lasts for 12 clock cycles in either
internal or external clock or acquisition mode.
Writing a new control byte during a conversion cycle will
abort the conversion and start a new acquisition interval.
Internal Acquisition
Select internal acquisition by writing the control byte with
the ACQMOD bit cleared (ACQMOD = 0). This causes
the write pulse to initiate an acquisition interval whose
duration is internally timed. Conversion starts when this
six-clock-cycle acquisition interval (3μs with f
CLK
=
2MHz) ends (see Figure 5).
External Acquisition
Use the external acquisition timing mode for precise con-
trol of the sampling aperture and/or independent control
of acquisition and conversion times. The user controls
acquisition and start-of-conversion with two separate
write pulses. The first pulse, written with ACQMOD = 1,
starts an acquisition interval of indeterminate length. The
second write pulse, written with ACQMOD = 0, termi-
nates acquisition and starts conversion on WR’s rising
edge (Figure 6). However, if the second control byte
contains ACQMOD = 1, an indefinite acquisition interval
is restarted.
The address bits for the input mux must have the same
values on the first and second write pulses. Power-down
mode bits (PD0, PD1) can assume new values on the
second write pulse (see Power-Down Mode section).
How to Read a Conversion
A standard interrupt signal, INT, is provided to allow the
device to flag the μP when the conversion has ended
and a valid result is available. INT goes low when con-
version is complete and the output data is ready
(Figures 5 and 6). It returns high on the first read cycle
or if a new control byte is written.
Multirange, S ingle +5V, 12-Bit DAS
with 12-Bit Bus Interfac e
10
______________________________________________________________________________________
t
CS
t
CSWS
t
WR
t
ACQI
t
CONV
t
DH
t
DS
t
INT1
t
D0
t
TR
HIGH-Z
HIGH-Z
t
CSRS
t
CSRH
CS
WR
D7–D0
INT
RD
DOUT
ACQMOD ="0"
DATA VALID
CBYTE
t
CSWH
Figure 5. Conversion Timing Using Internal Acquisition Mode
相關PDF資料 |
PDF描述 |
|---|---|
| MAX196BMYI | Multirange, Single %V, 12-Bit DAS with 12-Bit Bus Interface |
| MAX198BMYI | Multirange, Single %V, 12-Bit DAS with 12-Bit Bus Interface |
| MAX1961EEP | 2.35V to 5.5V, 0.5% Accurate, 1MHz PWM Step-Down Controllers with Voltage Margining |
| MAX1960 | 2.35V to 5.5V, 0.5% Accurate, 1MHz PWM Step-Down Controllers with Voltage Margining |
| MAX1960EEP | 2.35V to 5.5V, 0.5% Accurate, 1MHz PWM Step-Down Controllers with Voltage Margining |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX196BEAI+ | 功能描述:模數轉換器 - ADC 12-Bit 6Ch 100ksps 4.18V Precision ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX196BEAI+T | 功能描述:模數轉換器 - ADC 12-Bit 6Ch 100ksps 4.18V Precision ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX196BEAI-T | 功能描述:模數轉換器 - ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX196BENI | 功能描述:模數轉換器 - ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX196BENI+ | 功能描述:模數轉換器 - ADC 12-Bit 6Ch 100ksps 4.18V Precision ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
發布緊急采購，3分鐘左右您將得到回復。