- 您現在的位置：買賣IC網 > PDF目錄383341 > MAX1924XEEE (MAXIM INTEGRATED PRODUCTS INC) Advanced Li+ Battery-Pack Protectors PDF資料下載
參數資料
| 型號： | MAX1924XEEE |
| 廠商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分類： | 電源管理 |
| 英文描述： | Advanced Li+ Battery-Pack Protectors |
| 中文描述： | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO16 |
| 封裝： | 0.150 INCH, 0.025 INCH PITCH, QSOP-16 |
| 文件頁數： | 11/16頁 |
| 文件大?。?/td> | 308K |
| 代理商： | MAX1924XEEE |
M
Advanced Li+ Battery-Pack Protectors
______________________________________________________________________________________
11
Set the nominal values of the trickle charge current by
selecting resistor R
TKO
based on the following equation:
R
TKO
= (V
CHRG
- VP
ACK
)/I
TKO
where V
CHRG
is the charger output voltage, V
PACK
is
the battery-pack voltage, and I
TKO
is the trickle-charge
current.
When the trickle-charge option is not used, float
CGO
and connect
TKO
to the gate of the overcharge protec-
tion MOSFET (see Figure 9). When a charger is applied
and the voltage on one or more cells is less than
V
UV_TH
, the MAX1894/MAX1924 modulate the
TKO
out-
put until all cells exceed V
UV_TH
.
Protection FET Drivers
All three external MOSFETs have their source pins con-
nected to the SRC pin. When a MOSFET is turned off, FET
drivers pull the gate to the SRC voltage. Additional exter-
nal pullup resistors are not needed. When the MOSFET is
turned on, the V
GS
is limited to -14V by a clamp circuit
built in the drivers. This allows use of MOSFETs with maxi-
mum V
GS
of -20V. All three drivers have the same circuit-
ry and drive capability. The quiescent current in normal
operation is less than 3μA per driver.
R
SENSE
Selection
All current faults are detected using a current-sense
resistor connected between BN and PKN. The value of
this resistor sets the fault current levels. Charge-current
fault is given by:
Discharge-current fault is given by:
Pack-short current fault is given by:
Select R
SENSE
to obtain the desired fault current levels.
For example, a 20m
R
SENSE
sets the charge current
fault at 5A. Choose an R
SENSE
that can withstand the
dissipation during normal operation and current fault
conditions. For example, pack-short current is given by:
I
V
R
mV
R
PS TH
_
PS TH
_
SENSE
SENSE
=
=
405
I
V
R
mV
R
OD TH
_
OC TH
_
SENSE
SENSE
=
=
145
I
V
R
mV
R
OC_
OC TH
_
SENSE
SENSE
=
=
100
Figure 5. Charge-Current Fault
NORMAL OPERATION
V
B4P
> V
SRC
+ 0.1V
NO
YES
TKO, CGO = H
OC FAULT
V
RSENSE
< V
OC_TH
FOR 3ms
NO
YES
Figure 6. Discharge-Current Fault
NORMAL OPERATION
V
SRC
> V
B4P
+ 0.1V
NO
YES
DSO, TKO, CGO = H
OD FAULT
V
RSENSE
> V
OD_TH
FOR 3ms
NO
YES
相關PDF資料 |
PDF描述 |
|---|---|
| MAX1924VEEE | Advanced Li+ Battery-Pack Protectors |
| MAX1894 | Fixed-Point Digital Signal Processor 256-BGA |
| MAX1894-MAX1924 | Fixed-Point Digital Signal Processor 288-FCBGA |
| MAX1925 | Fixed-Point Digital Signal Processor 548-FCBGA |
| MAX1926 | Switch-Mode 1-Cell Li+ Chargers |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX1924XEEE+ | 功能描述:電池管理 RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel |
| MAX1924XEEE+T | 制造商:Maxim Integrated Products 功能描述:SMALLEST LI+ PROTECTION SOLUTION ALSO OFFERS THE MOST COMPLE - Tape and Reel |
| MAX1925ETC | 功能描述:電池管理 Switch-Mode 1-Cell Li+ Charger RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel |
| MAX1925ETC+ | 功能描述:電池管理 Switch-Mode 1-Cell Li+ Charger RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel |
| MAX1925ETC+T | 功能描述:電池管理 Switch-Mode 1-Cell Li+ Charger RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。