- 您現在的位置：買賣IC網 > PDF目錄383340 > MAX1902ETJ (MAXIM INTEGRATED PRODUCTS INC) 500kHz Multi-Output, Low-Noise Power-Supply Controllers for Notebook Computers PDF資料下載
參數資料
| 型號： | MAX1902ETJ |
| 廠商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分類： | 穩壓器 |
| 英文描述： | 500kHz Multi-Output, Low-Noise Power-Supply Controllers for Notebook Computers |
| 中文描述： | 0.2 A DUAL SWITCHING CONTROLLER, 550 kHz SWITCHING FREQ-MAX, QCC32 |
| 封裝： | 5 X 5 MM, 0.80 MM, MO-220WHHD-2, TQFN-32 |
| 文件頁數： | 19/33頁 |
| 文件大?。?/td> | 649K |
| 代理商： | MAX1902ETJ |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁當前第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁
M
500kHz Multi-Output, Low-Noise Power-Supply
Controllers for Notebook Computers
______________________________________________________________________________________
19
Interference due to switching noise is reduced in PWM
mode by ensuring a constant switching frequency, thus
concentrating the emissions at a known frequency out-
side the system audio or IF bands. Choose an oscillator
frequency for which switching frequency harmonics
don
’
t overlap a sensitive frequency band. If necessary,
synchronize the oscillator to a tight-tolerance external
clock generator. To extend the output-voltage regula-
tion range, constant operating frequency is not main-
tained under overload or dropout conditions (see the
Dropout Operation
section).
PWM mode (
SKIP
= high) forces two changes upon the
PWM controllers. First, it disables the minimum-current
comparator, ensuring fixed-frequency operation.
Second, it changes the detection threshold for reverse
current limit from 0 to -100mV, allowing the inductor cur-
rent to reverse at light loads. This results in fixed-fre-
quency operation and continuous inductor-current flow.
This eliminates discontinuous-mode inductor ringing and
improves cross regulation of transformer-coupled multi-
ple-output supplies, particularly in circuits that don
’
t use
additional secondary regulation via SECFB or V
DD
.
In most applications, tie
SKIP
to GND to minimize qui-
escent supply current. VL supply current with
SKIP
high
is typically 30mA, depending on external MOSFET gate
capacitance and switching losses.
Internal Digital Soft-Start Circuit
Soft-start allows a gradual increase of the internal cur-
rent-limit level at startup to reduce input surge currents.
Both SMPSs contain internal digital soft-start circuits,
each controlled by a counter, a digital-to-analog con-
verter (DAC), and a current-limit comparator. In shut-
down or standby mode, the soft-start counter is reset to
zero. When an SMPS is enabled, its counter starts
counting oscillator pulses, and the DAC begins incre-
menting the comparison voltage applied to the current-
limit comparator. The DAC output increases from 0 to
100mV in five equal steps as the count increases to
512 clocks. As a result, the main output capacitor
charges up relatively slowly. The exact time of the out-
put rise depends on output capacitance and load cur-
rent, and is typically 600μs with a 500kHz oscillator.
Dropout Operation
Dropout (low input-output differential operation) is
enhanced by stretching the clock pulse width to
increase the maximum duty factor. The algorithm fol-
lows: If the output voltage (V
OUT
) drops out of regula-
tion without the current limit having been reached, the
SMPS skips an off-time period (extending the on-time).
At the end of the cycle, if the output is still out of regula-
tion, the SMPS skips another off-time period. This
action can continue until three off-time periods are
skipped, effectively dividing the clock frequency by as
much as four.
The typical PWM minimum off-time is 300ns, regardless
of the operating frequency. Lowering the operating fre-
quency raises the maximum duty factor above 97%.
Adjustable-Output Feedback
(Dual Mode FB)
Fixed, preset output voltages are selected when FB_ is
connected to ground. Adjusting the main output volt-
age with external resistors is simple for any of the
MAX1901/MAX1902/MAX1904, through resistor divi-
ders connected to FB3 and FB5 (Figure 2). Calculate
the output voltage with the following formula:
V
OUT
= V
REF
(1 + R1 / R2)
where V
REF
= 2.5V nominal.
The nominal output should be set approximately 1% or
2% high to make up for the MAX1901/MAX1902/
MAX1904 -2% typical load-regulation error. For exam-
ple, if designing for a 3.0V output, use a resistor ratio
that results in a nominal output voltage of 3.05V. This
slight offsetting gives the best possible accuracy.
Recommended normal values for R2 range from 5k
to
100k
. To achieve a 2.5V nominal output, simply con-
nect FB_ directly to CSL_.
Remote output-voltage sensing, while not possible in
fixed-output mode due to the combined nature of the
voltage-sense and current-sense inputs (CSL3 and
CSL5), is easy to do in adjustable mode by using the top
of the external resistor-divider as the remote sense point.
When using adjustable mode, it is a good idea to
always set the
“
3.3V output
”
to a lower voltage than the
“
5V output.
”
The 3.3V output must always be less than
VL, so that the voltage on CSH3 and CSL3 is within the
common-mode range of the current-sense inputs. While
VL is nominally 5V, it can be as low as 4.7V when lin-
early regulating, and as low as 4.2V when automatically
bootstrapped to CSH5.
Secondary Feedback Regulation Loop
(SECFB or V
DD
)
A flyback-winding control loop regulates a secondary
winding output, improving cross-regulation when the
primary output is lightly loaded or when there is a low
input-output differential voltage. If V
DD
or SECFB falls
below its regulation threshold, the low-side switch is
turned on for an extra 0.75μs. This reverses the induc-
相關PDF資料 |
PDF描述 |
|---|---|
| MAX1904EAI | 500kHz Multi-Output, Low-Noise Power-Supply Controllers for Notebook Computers |
| MAX1904ETJ | 500kHz Multi-Output, Low-Noise Power-Supply Controllers for Notebook Computers |
| MAX1909 | Multichemistry Battery Charger with Automatic System Power Selector |
| MAX1909ETI | Multichemistry Battery Charger with Automatic System Power Selector |
| MAX190AENG | Low-Power, 12-Bit Sampling ADCs with Internal Reference and Power-Down |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX1904BEAI | 制造商:Maxim Integrated Products 功能描述: |
| MAX1904BEAI+ | 功能描述:DC/DC 開關控制器 500kHz Multi-Output Power-Supply Ctlr RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK |
| MAX1904BEAI+T | 功能描述:DC/DC 開關控制器 500kHz Multi-Output Power-Supply Ctlr RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK |
| MAX1904EAI | 功能描述:DC/DC 開關控制器 RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK |
| MAX1904EAI+ | 功能描述:DC/DC 開關控制器 500kHz Multi-Output Power-Supply Ctlr RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK |
發布緊急采購，3分鐘左右您將得到回復。