- 您現在的位置：買賣IC網 > PDF目錄383339 > MAX1879EUA (MAXIM INTEGRATED PRODUCTS INC) Simple, Efficient, 1-Cell Li+ Pulse Charger PDF資料下載
參數資料
| 型號： | MAX1879EUA |
| 廠商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分類： | 穩壓器 |
| 英文描述： | Simple, Efficient, 1-Cell Li+ Pulse Charger |
| 中文描述： | BATTERY CHARGE CONTROLLER, PDSO8 |
| 封裝： | MICRO MAX PACKAGE-8 |
| 文件頁數： | 8/11頁 |
| 文件大?。?/td> | 198K |
| 代理商： | MAX1879EUA |
M
Simple, Efficient, 1-Cell Li+ Pulse Charger
8
_______________________________________________________________________________________
Detailed Description
Initiating a Charge Cycle
The MAX1879 initiates fast-charge upon insertion of a
battery or application of an external power source (cur-
rent-limited AC wall adapter). After charge completion,
charging restarts if the cell voltage falls below 4.0V or
when THERM is pulled above 1.4V after the charge
timer expires (approximately 6.25hr).
Before a charge cycle can begin, cell conditions are
verified to be within safe limits. The cell voltage must be
greater than 2.5V but less than the regulation voltage
(default value 4.2V). In addition, the thermistor must
indicate an acceptable cell temperature (default range
+2.5
°
C to +47.5
°
C). See the
Applications Information
section.
Li+ cells can be damaged when fast-charged from a
completely dead state. Moreover, a fully discharged
cell may indicate a dangerous abnormal cell condition.
As a built-in safety feature, the MAX1879 precharges
the Li+ cell with 8mA at the start of a charge cycle if the
cell voltage is below 2.5V. As soon as the cell reaches
2.5V and the safety conditions are met (see the
Fast-
Charge
section), fast-charging begins.
If the temperature moves outside the programmed
range, the charger pauses. When the temperature
returns to the safe charging range, the charging cycle
continues, and the charge timer resumes counting from
the point at which the temperature fault occurred. The
timer is not reset. The MAX1879 monitors these condi-
tions throughout the charging cycle.
Fast-Charge
Once cell conditions are determined to be satisfactory,
the MAX1879 fast-charges the Li+ cell by pulling GATE
low, turning on the external PMOS FET. Cell charging
current is set by the current limit of the external power
supply; it is not regulated by the MAX1879. The PMOS
FET operates only as a switch, not as a linear regulator.
Therefore, power dissipation is minimized, permitting
rapid charge cycles with minimal heat generation. The
external power supply must have a specified current
limit that matches the desired fast-charge current for
the Li+ cell.
The MAX1879 uses a hysteretic algorithm with mini-
mum on-times and minimum off-times to top-off the cell.
The cell voltage is sampled every 2ms. If V
BATT
is less
than the battery regulation voltage, the external PMOS
FET turns on or remains on. If the cell voltage is greater
than or equal to the battery regulation voltage, the FET
turns off and remains off for the minimum off-time. By
measuring the cell voltage when the PMOS FET is off
as well as when it is on, the MAX1879 eliminates bat-
tery-voltage sensing errors due to charging current
flowing through the series resistance of cell protection
switches or fuse links in the charging path. Fast-charge
continues until the on/off duty cycle falls to 1/8, then the
CHG
LED turns off, indicating that the battery is
charged to approximately 95% of full capacity.
Pulsed Top-Off Charge
At the beginning of the Top-Off state, the current stays
on for a 1/8 duty cycle. As the cell continues to charge,
the percentage of time spent in the
“
current-on
”
mode
decreases. Towards the end of top-off, the current
stays off for many cycles between single
“
on
”
pulses.
During these final pulses, the instantaneous cell voltage
may exceed the battery regulation voltage, but the
duration of these pulses is several orders of magnitude
shorter than the intrinsic chemical time constant of the
Li+ cell. This does not harm the cell. Cell top-off is com-
pleted when the charging timer expires (approximately
6.25hr).
Charge Status with
CHG
CHG
indicates the cell
’
s charging status. An LED can
be connected directly from IN to
CHG
for a visible indi-
cator. Alternatively, a pullup resistor (100k
) from a
logic supply to
CHG
provides a logic-level output.
Table 1 relates the LED status to the charger condition.
Applications Information
The MAX1879 was designed to offer the maximum inte-
gration and functionality in the smallest, most basic
application circuit possible. The only necessary exter-
nal components are a current-limited wall cube, a
PMOS FET, two small capacitors, and a 10k
thermis-
tor/resistor. This simple application circuit appears in
Figure 1. Optionally (as shown in Figure 2), an LED can
be added as a charge-state indicator, a resistor (R
ADJ
)
can be used to trim down the maximum charge voltage
Table 1.
CHG
Output States
CONDITION
CHG
(LED)
No battery or no charger, or
cell voltage < 2.2V
High impedance (LED off)
Fast-charge in progress
Low (LED on)
Top- Off: on/off d uty cycl e < 1/8
High impedance (LED off)
Done (charge complete)
Temperature fault
High impedance (LED off)
LED blinks at 2Hz
Prequalification
(2.2V < V
BATT
< 2.5V)
LED blinks at 2Hz
相關PDF資料 |
PDF描述 |
|---|---|
| MAX187ACPA | +5V, Low-Power, 12-Bit Serial ADCs |
| MAX187AEPA | LJT 12C 8#20 4#16 PIN PLUG |
| MAX189AEPA | +5V, Low-Power, 12-Bit Serial ADCs |
| MAX187AEWE | +5V, Low-Power, 12-Bit Serial ADCs |
| MAX189AEWE | Circular Connector; No. of Contacts:22; Series:MS27467; Body Material:Aluminum; Connecting Termination:Crimp; Connector Shell Size:13; Circular Contact Gender:Pin; Circular Shell Style:Straight Plug; Insert Arrangement:13-35 RoHS Compliant: No |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX1879EUA+ | 功能描述:電池管理 1-Cell Li+ Pulse Charger RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel |
| MAX1879EUA+T | 功能描述:電池管理 1-Cell Li+ Pulse Charger RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel |
| MAX1879EUA-T | 功能描述:電池管理 1-Cell Li+ Pulse Charger RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel |
| MAX1879EVKIT | 制造商:Maxim Integrated Products 功能描述:SMALLEST, SIMPLE 1-CELL LI- PULSE CHARGER WIT - Bulk |
| MAX187ACPA | 功能描述:模數轉換器 - ADC Integrated Circuits (ICs) RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
發布緊急采購，3分鐘左右您將得到回復。