- 您現在的位置：買賣IC網 > PDF目錄383339 > MAX1875AEEG (MAXIM INTEGRATED PRODUCTS INC) Dual 180∑ Out-of-Phase Buck Controllers with Sequencing/Prebias Startup and POR PDF資料下載
參數資料
| 型號： | MAX1875AEEG |
| 廠商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分類： | 穩壓器 |
| 英文描述： | Dual 180∑ Out-of-Phase Buck Controllers with Sequencing/Prebias Startup and POR |
| 中文描述： | DUAL SWITCHING CONTROLLER, 660 kHz SWITCHING FREQ-MAX, PDSO24 |
| 封裝： | 0.150 INCH, 0.25 INCH PITCH, MO-137AE, QSOP-24 |
| 文件頁數： | 19/21頁 |
| 文件大?。?/td> | 493K |
| 代理商： | MAX1875AEEG |
Keep the power traces and load connections short.
This practice is essential for high efficiency. Use
thick copper PC boards (2oz vs. 1oz) to enhance
full-load efficiency by 1% or more.
LX_ and PGND connections to the synchronous rec-
tifiers for current limiting must be made using Kelvin
sense connections to guarantee the current-limit
accuracy. With 8-pin SO MOSFETs, this is best done
by routing power to the MOSFETs from outside
using the top copper layer, while connecting PGND
and LX_ underneath the 8-pin SO package.
When trade-offs in trace lengths must be made,
allow the inductor-charging path to be made longer
than the discharge path. Since the average input
current is lower than the average output current in
step-down converters, this minimizes the power dis-
sipation and voltage drops caused by board resis-
tance. For example, allow some extra distance
between the input capacitors and the high-side
MOSFET rather than to allow distance between the
inductor and the low-side MOSFET or between the
inductor and the output filter capacitor.
Ensure that the feedback connection to C
OUT_
is
short and direct.
Route high-speed switching nodes (BST_, LX_, DH_,
and DL_) away from the sensitive analog areas
(REF, COMP_, ILIM_, and FB_). Use PGND1 and
PGND2 as EMI shields to keep radiated noise away
from the IC, feedback dividers, and analog bypass
capacitors.
Make all pin-strap control input connections (ILIM_,
SYNC, and EN) to analog ground (GND) rather than
power ground (PGND).
Layout Procedure
1) Place the power components first, with ground termi-
nals adjacent (N
L
_ source, C
IN
_, and C
OUT
_). Make
all these connections on the top layer with wide, cop-
per-filled areas (2oz copper recommended).
2) Mount the controller IC adjacent to the synchronous
rectifier MOSFETs (N
L
_), preferably on the back
side in order to keep LX_, PGND_, and DL_ traces
short and wide. The DL_ gate trace must be short
and wide, measuring 50mils to 100mils wide if the
low-side MOSFET is 1in from the controller IC.
3) Group the gate-drive components (BST_ diodes and
capacitors, and V
L
bypass capacitor) together near
the controller IC.
4) Make the DC-DC controller ground connections as
follows: create a small analog ground plane near the
IC. Connect this plane to GND and use this plane for
the ground connection for the reference (REF) V+
bypass capacitor, compensation components, feed-
back dividers, OSC resistor, and ILIM_ resistors (if
any). Connect GND and PGND together under the
IC (this is the only connection between GND and
PGND).
5) On the board
’
s top side (power planes), make a star
ground to minimize crosstalk between the two sides.
Chip Information
TRANSISTOR COUNT: 6688
PROCESS: BiCMOS
M
Dual 180° Out-of-Phase PWM Step-
Down Controllers with POR
______________________________________________________________________________________
19
相關PDF資料 |
PDF描述 |
|---|---|
| MAX1875EEG | Fixed-Point Digital Signal Processor 288-BGA MICROSTAR |
| MAX1876 | Fixed-Point Digital Signal Processor 288-BGA MICROSTAR |
| MAX1876AEEG | Fixed-Point Digital Signal Processor 288-BGA MICROSTAR |
| MAX1876EEG | Fixed-Point Digital Signal Processor 288-BGA MICROSTAR |
| MAX1879 | Simple, Efficient, 1-Cell Li+ Pulse Charger |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX1875AEEG+ | 功能描述:電壓模式 PWM 控制器 Dual 180 Out PWM Step-Down RoHS:否 制造商:Texas Instruments 輸出端數量:1 拓撲結構:Buck 輸出電壓:34 V 輸出電流: 開關頻率: 工作電源電壓:4.5 V to 5.5 V 電源電流:600 uA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 封裝 / 箱體:WSON-8 封裝:Reel |
| MAX1875AEEG+T | 功能描述:電壓模式 PWM 控制器 Dual 180 Out PWM Step-Down RoHS:否 制造商:Texas Instruments 輸出端數量:1 拓撲結構:Buck 輸出電壓:34 V 輸出電流: 開關頻率: 工作電源電壓:4.5 V to 5.5 V 電源電流:600 uA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 封裝 / 箱體:WSON-8 封裝:Reel |
| MAX1875AEEG-T | 功能描述:DC/DC 開關控制器 RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK |
| MAX1875EEG | 功能描述:DC/DC 開關控制器 RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK |
| MAX1875EEG+ | 功能描述:電壓模式 PWM 控制器 Dual 180 Out PWM Step-Down RoHS:否 制造商:Texas Instruments 輸出端數量:1 拓撲結構:Buck 輸出電壓:34 V 輸出電流: 開關頻率: 工作電源電壓:4.5 V to 5.5 V 電源電流:600 uA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 封裝 / 箱體:WSON-8 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。