參數資料
型號： MAX1858EEG
廠商： MAXIM INTEGRATED PRODUCTS INC
元件分類： 穩壓器
英文描述： Dual 180∑ Out-of-Phase PWM Step-Down Controller with Power Sequencing and POR
中文描述： DUAL SWITCHING CONTROLLER, 600 kHz SWITCHING FREQ-MAX, PDSO24
封裝： 0.150 INCH, QSOP-24
文件頁數： 20/22頁
文件大?。?/td> 553K
代理商： MAX1858EEG
M
Dual 180° Out-of-Phase Buck Controllers with
Sequencing/Prebias Startup and POR
20
______________________________________________________________________________________
Applications Information
Dropout Performance
When working with low input voltages, the output-volt-
age adjustable range for continuous-conduction opera-
tion is restricted by the minimum off-time (t
OFF(MIN)
).
For best dropout performance, use the lowest (100kHz)
switching-frequency setting. Manufacturing tolerances
and internal propagation delays introduce an error to
the switching frequency and minimum off-time specifi-
cations. This error is more significant at higher frequen-
cies. Also, keep in mind that transient response
performance of buck regulators operated close to
dropout is poor, and bulk output capacitance must
often be added (see the V
SAG
equation in the
Design
Procedure
section).
The absolute point of dropout is when the inductor cur-
rent ramps down during the minimum off-time (
I
DOWN
)
as much as it ramps up during the maximum on-time
(
I
UP
). The ratio h =
I
UP
/
I
DOWN
is an indicator of the
ability to slew the inductor current higher in response to
increased load, and must always be greater than 1. As
h approaches 1, the absolute minimum dropout point,
the inductor current cannot increase as much during
each switching cycle and V
SAG
greatly increases
unless additional output capacitance is used.
A reasonable minimum value for h is 1.5, but adjusting
this up or down allows tradeoffs between V
SAG
, output
capacitance, and minimum operating voltage. For a
given value of h, the minimum operating voltage can be
calculated as:
where V
DROP1
is the sum of the parasitic voltage drops
in the inductor discharge path, including synchronous
rectifier, inductor, and PC board resistances; V
DROP2
is
the sum of the resistances in the charging path, includ-
ing high-side switch, inductor, and PC board resis-
tances; and t
OFF(MIN)
is from the
Electrical
Characteristics
. The absolute minimum input voltage is
calculated with h = 1.
If the calculated V+
(MIN)
is greater than the required
minimum input voltage, then reduce the operating fre-
quency or add output capacitance to obtain an accept-
able V
SAG
. If operation near dropout is anticipated,
calculate V
SAG
to be sure of adequate transient
response.
Dropout design example:
V
OUT
= 5V
f
SW
= 600kHz
t
OFF(MIN)
= 250ns
V
DROP1
= V
DROP2
= 100mV
h = 1.5
Calculating again with h = 1 gives the absolute limit of
dropout:
Therefore, V
IN
must be greater than 6V, even with very
large output capacitance, and a practical input voltage
with reasonable output capacitance would be 6.58V.
Improving Noise Immunity
Applications where the MAX1858A/MAX1875A/
MAX1876A must operate in noisy environments can
typically adjust their controller
’
s compensation to
improve the system
’
s noise immunity. In particular,
high-frequency noise coupled into the feedback loop
causes jittery duty cycles. One solution is to lower the
crossover frequency (see the
Compensation
section).
PC Board Layout Guidelines
Careful PC board layout is critical to achieve low switch-
ing losses and clean, stable operation. This is especially
true for dual converters where one channel can affect
the other. Refer to the MAX1858 EV kit or MAX1875 EV
kit data sheet for specific layout examples.
If possible, mount all the power components on the top
side of the board with their ground terminals flush
against one another. Follow these guidelines for good
PC board layout:
Isolate the power components on the top side from
the analog components on the bottom side with a
ground shield. Use a separate PGND plane under
the OUT1 and OUT2 sides (referred to as PGND1
and PGND2). Avoid the introduction of AC currents
into the PGND1 and PGND2 ground planes. Run the
power plane ground currents on the top side only.
V
V
mV
)(
250
kHz
100
ns
=
6
mV
mV
V
IN MIN
(
)
(
)
=
+
+
5
100
1 600
100
-
V
V
mV
)(
=
kHz
mV
ns
mV
V
IN MIN
(
)
. (
)
.
=
+
+
5
100
1 1 5 600
100
250
6 58
100
-
V
V
V
hf
V
V
IN MIN
(
OUT
SW OFF MIN
1-
DROP
(
DROP
DROP
)
)
=
+
+
1
2
1
-
相關PDF資料
PDF描述
MAX1858A-MAX1876A Dual 180∑ Out-of-Phase Buck Controllers with Sequencing/Prebias Startup and POR
MAX1858A Dual 180?Out-of-Phase Buck Controllers with Sequencing/Prebias Startup and POR
MAX1875A Dual 180?Out-of-Phase Buck Controllers with Sequencing/Prebias Startup and POR
MAX1876A Dual 180?Out-of-Phase Buck Controllers with Sequencing/Prebias Startup and POR
MAX1858AEEG Dual 180∑ Out-of-Phase Buck Controllers with Sequencing/Prebias Startup and POR
相關代理商/技術參數
參數描述
MAX1858EEG+ 功能描述:電壓模式 PWM 控制器 Dual 180 Out Buck Controllers RoHS:否 制造商:Texas Instruments 輸出端數量:1 拓?fù)浣Y(jié)構:Buck 輸出電壓:34 V 輸出電流: 開關頻率: 工作電源電壓:4.5 V to 5.5 V 電源電流:600 uA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 封裝 / 箱體:WSON-8 封裝:Reel
MAX1858EEG+T 功能描述:電壓模式 PWM 控制器 Dual 180 Out Buck Controllers RoHS:否 制造商:Texas Instruments 輸出端數量:1 拓?fù)浣Y(jié)構:Buck 輸出電壓:34 V 輸出電流: 開關頻率: 工作電源電壓:4.5 V to 5.5 V 電源電流:600 uA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 封裝 / 箱體:WSON-8 封裝:Reel
MAX1858EEG-T 功能描述:DC/DC 開關控制器 RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK
MAX1858EVKIT 功能描述:DC/DC 開關控制器 Evaluation Kit for the MAX1858 MAX1875 MAX1876 RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK
MAX185ACNG 功能描述:模數轉換器 - ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*