參數資料
型號: MAX1845EEI
廠商: MAXIM INTEGRATED PRODUCTS INC
元件分類: 穩壓器
英文描述: Dual, High-Efficiency, Step-Down Controller with Accurate Current Limit
中文描述: DUAL SWITCHING CONTROLLER, 620 kHz SWITCHING FREQ-MAX, PDSO28
封裝: 0.150 INCH, 0.025 INCH PITCH, MO-137AD, QSOP-28
文件頁數: 22/27頁
文件大?。?/td> 543K
代理商: MAX1845EEI
M
Dual, High-Efficiency, Step-Down
Controller with Accurate Current Limit
22
______________________________________________________________________________________
mount all of the power components on the top side of
the board, with connecting terminals flush against one
another.
Keep the high-current paths short, especially at the
ground terminals. This practice is essential for stable,
jitter-free operation. Short power traces and load con-
nections are essential for high efficiency. Using thick
copper PC boards (2oz vs. 1oz) can enhance full-load
efficiency by 1% or more. Correctly routing PC board
traces is a difficult task that must be approached in
terms of fractions of centimeters, where a single mil-
liohm of excess trace resistance causes a measurable
efficiency penalty.
Place the current-sense resistors close to the top-side
star-ground point (where the IC ground connects to the
top-side ground plane) to minimize current-sensing
errors. Avoid additional current-sensing errors by using
a Kelvin connection from CS_ pins to the sense resis-
tors.
The following guidelines are in order of importance:
Keep the space between the ground connection of
the current-sense resistors short and near the via to
the IC ground pin.
Minimize the resistance on the low-side path. The
low-side path starts at the ground of the low-side
FET, goes through the low-side FET, through the
inductor, through the output capacitor, and returns
to the ground of the low-side FET. Minimize the resis-
tance by keeping the components close together
and the traces short and wide.
Minimize the resistance in the high-side path. This
path starts at V
IN
, goes through the high-side FET,
DL_
GND
OUT_
CS_
DH_
FB_
V
BATT
V
OUT
R1
R2
MAX1845
Figure 9. Setting V
OUT
with a Resistor-Divider
MAX1845
TO ERROR
AMP1
TO ERROR
AMP2
OUT2
FB2
0.1V
2V
0.1V
FB1
FIXED
2.5V
FIXED
1.5V
FIXED
1.8V
OUT1
Figure 8. Feedback Mux
AGND PLANE
AGND PLANE
PGND PLANE
VIA TO OUT1
VIA TO PGND PLANE AND IC GND
VIA TO CS1
NOTCH
V
IN
USE AGND PLANE TO:
- BYPASS V
AND REF
- TERMINATE EXTERNAL FB, ILIM,
OVP DIVIDERS, IF USED
- PIN-STRAP CONTROL
INPUTS
USE PGND PLANE TO:
- BYPASS V
- CONNECT IC GROUND
TO TOP-SIDE STAR GROUND
VIA TO TOP-SIDE
GROUND
TOP-SIDE GROUND PLANE
L2
L1
C1
C2
Q1
Q2
Q3
Q4
C
IN
C
IN
C
IN
D2
D1
Figure 10. PC Board Layout Example
相關PDF資料
PDF描述
MAX1845ETX Dual, High-Efficiency, Step-Down Controller with Accurate Current Limit
MAX1848 Replaced by TMS320VC5506 : DSP (DSP Only) for Embedded V90 Modem Solution [Not Recommended For New Designs (NRND)] 144-LQFP
MAX1848ETA Replaced by TMS320VC5506 : DSP (DSP Only) for Embedded V90 Modem Solution [Not Recommended For New Designs (NRND)] 144-BGA MICROSTAR
MAX1848EKA White LED Step-Up Converter in SOT23
MAX1855 Fixed-Point Digital Signal Processor 352-FC/CSP 0 to 0
相關代理商/技術參數
參數描述
MAX1845EEI+ 功能描述:電流型 PWM 控制器 Step-Down Controller RoHS:否 制造商:Texas Instruments 開關頻率:27 KHz 上升時間: 下降時間: 工作電源電壓:6 V to 15 V 工作電源電流:1.5 mA 輸出端數量:1 最大工作溫度:+ 105 C 安裝風格:SMD/SMT 封裝 / 箱體:TSSOP-14
MAX1845EEI+T 功能描述:電流型 PWM 控制器 Step-Down Controller RoHS:否 制造商:Texas Instruments 開關頻率:27 KHz 上升時間: 下降時間: 工作電源電壓:6 V to 15 V 工作電源電流:1.5 mA 輸出端數量:1 最大工作溫度:+ 105 C 安裝風格:SMD/SMT 封裝 / 箱體:TSSOP-14
MAX1845EEI-T 功能描述:電流型 PWM 控制器 RoHS:否 制造商:Texas Instruments 開關頻率:27 KHz 上升時間: 下降時間: 工作電源電壓:6 V to 15 V 工作電源電流:1.5 mA 輸出端數量:1 最大工作溫度:+ 105 C 安裝風格:SMD/SMT 封裝 / 箱體:TSSOP-14
MAX1845EEI-TG05 制造商:Rochester Electronics LLC 功能描述: 制造商:Maxim Integrated Products 功能描述:
MAX1845EEI-TG068 制造商:Rochester Electronics LLC 功能描述: 制造商:Maxim Integrated Products 功能描述: