- 您現在的位置：買賣IC網 > PDF目錄385522 > MAX1809EEE (MAXIM INTEGRATED PRODUCTS INC) 3A, 1MHz, DDR Memory Termination Supply PDF資料下載
參數資料
| 型號： | MAX1809EEE |
| 廠商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分類： | 穩壓器 |
| 英文描述： | 3A, 1MHz, DDR Memory Termination Supply |
| 中文描述： | 4.7 A SWITCHING REGULATOR, 1000 kHz SWITCHING FREQ-MAX, PDSO16 |
| 封裝： | QSOP-16 |
| 文件頁數： | 10/17頁 |
| 文件大?。?/td> | 803K |
| 代理商： | MAX1809EEE |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁當前第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁
M
3A, 1MHz, DDR Memory Termination Supply
10
______________________________________________________________________________________
to maximum DC load current. A higher value of LIR
allows smaller inductance but results in higher losses
and ripple. A good compromise between size and losses
is found at approximately a 25% ripple current to load
current ratio (LIR = 0.25).
(
(
The peak inductor current at full load is calculated by:
where I
OUT
is the maximum source or sink current.
Choose an inductor with a saturation current at least as
high as the peak inductor current. Additionally, verify
the peak inductor current while sourcing output current
(I
OUT
= I
SOURCE
) does not exceed the positive current
limit. The inductor selected should exhibit low losses at
the chosen operating frequency.
Input Capacitor Selection
The input filter capacitor reduces peak currents and
noise at the voltage source. Use a low-ESR and low-
ESL capacitor located no further than 5mm from IN.
Select the input capacitor according to the RMS input
ripple-current requirements and voltage rating:
where I
RIPPLE
= input RMS current ripple.
Output Capacitor Selection
The output filter capacitor affects the output voltage
ripple, output load-transient response, and feedback
loop stability. The output filter capacitor must have low
enough ESR to meet output ripple and load transient
requirements, yet have high enough ESR to satisfy sta-
bility requirements. Also, the capacitance value must
be high enough to guarantee stability and absorb the
inductor energy going from a full-load sourcing to full-
load sinking condition without exceeding the maximum
output tolerance.
For stable operation, the MAX1809 requires a minimum
feedback ripple voltage of V
RIPPLE
≥
1%
V
EXTREF
.
The minimum ESR of the output capacitor should be:
R
ESR
> 1%
(L / t
OFF
)
Stable operation requires the correct output filter
capacitor. When choosing the output capacitor, ensure
that:
In applications where the output is subject to large load
transients, the output capacitor
’
s size typically depends
on how much ESR is needed to prevent the output from
dipping too low under a load transient. Ignoring the sag
due to finite capacitance:
R
ESR
≤
V
OUT
/
I
OUT(MAX)
The actual microfarad capacitance value required is
defined by the physical size needed to achieve low
ESR, and by the chemistry of the capacitor technology.
Thus, the capacitor is usually selected by ESR, size,
and voltage rating rather than by capacitance value
(this is true of tantalums, OS-CONs, and other elec-
trolytics). When using low-capacity filter capacitors
such as ceramic or polymer types, capacitor size is
usually determined by the capacity needed to prevent
V
SAG
and V
SOAR
from causing problems during load
transients. Generally, once enough capacitance is
added to meet the overshoot requirement, undershoot
at the rising-load edge is no longer a problem. The
amount of overshoot and undershoot due to stored
inductor energy can be calculated as:
V
SOAR
= L
I
OUT
2
/(2
C
OUT
V
OUT
)
V
SAG
= L
I
OUT
2
/[2
C
OUT
(V
IN
- V
OUT
)]
Soft-Start
Soft-start allows a gradual increase of the internal current
limit to reduce input surge currents at startup and at exit
from shutdown. A timing capacitor, C
SS
, placed from SS
to GND sets the rate at which the internal current limit is
changed. Upon power-up, when the device comes out of
undervoltage lockout (2.6V typ) or after the
SHDN
pin is
pulled high, a 4μA constant current source charges the
soft-start capacitor and the voltage on SS increases.
When the voltage on SS is less than approximately 0.7V,
the current limit is set to zero. As the voltage increases
from 0.7V to approximately 1.8V, the current limit is
adjusted from 0V to the current-limit threshold (see the
Electrical Characteristics
). The voltage across the soft-
start capacitor changes with time according to the
equation:
V
A
t
C
SS
SS
=
μ
×
4
C
t
V
FV
s
OUT
OFF
OUT
≥
×
μ
79
μ
/
I
I
V
V
V
V
RIPPLE
OUT
OUT
IN
OUT
IN
=
×
(
)
I
I
V
t
L
PEAK
OUT
OUT
OFF
=
+
×
×
(
)
2
L
V
t
I
I
LIR
OUT
OFF
SOURCE
SINK
=
×
)
)
×
相關PDF資料 |
PDF描述 |
|---|---|
| MAX1809ETI | 3A, 1MHz, DDR Memory Termination Supply |
| MAX181 | Completed ,8 Channel 12 Bits Data Acquisition System(100ksps,8通道，并行，12位A/D轉換器) |
| MAX1852 | SC70 Inverting Charge Pumps with Shutdown |
| MAX1852EXT | SC70 Inverting Charge Pumps with Shutdown |
| MAX1853 | SC70 Inverting Charge Pumps with Shutdown |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX1809EEE+ | 功能描述:電壓模式 PWM 控制器 3A 1MHz DDR Memory Termination Supply RoHS:否 制造商:Texas Instruments 輸出端數量:1 拓?fù)浣Y(jié)構:Buck 輸出電壓:34 V 輸出電流: 開關頻率: 工作電源電壓:4.5 V to 5.5 V 電源電流:600 uA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 封裝 / 箱體:WSON-8 封裝:Reel |
| MAX1809EEE+T | 功能描述:電壓模式 PWM 控制器 3A 1MHz DDR Memory Termination Supply RoHS:否 制造商:Texas Instruments 輸出端數量:1 拓?fù)浣Y(jié)構:Buck 輸出電壓:34 V 輸出電流: 開關頻率: 工作電源電壓:4.5 V to 5.5 V 電源電流:600 uA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 封裝 / 箱體:WSON-8 封裝:Reel |
| MAX1809EEE-T | 功能描述:直流/直流開關轉換器 RoHS:否 制造商:STMicroelectronics 最大輸入電壓:4.5 V 開關頻率:1.5 MHz 輸出電壓:4.6 V 輸出電流:250 mA 輸出端數量:2 最大工作溫度:+ 85 C 安裝風格:SMD/SMT |
| MAX1809EGI | 功能描述:直流/直流開關轉換器 RoHS:否 制造商:STMicroelectronics 最大輸入電壓:4.5 V 開關頻率:1.5 MHz 輸出電壓:4.6 V 輸出電流:250 mA 輸出端數量:2 最大工作溫度:+ 85 C 安裝風格:SMD/SMT |
| MAX1809EGI+ | 制造商:Maxim Integrated Products 功能描述:- Rail/Tube |
發布緊急采購，3分鐘左右您將得到回復。