- 您現在的位置：買賣IC網 > PDF目錄383334 > MAX1748 (Maxim Integrated Products, Inc.) Triple-Output TFT LCD DC-DC Converter PDF資料下載
參數資料
| 型號： | MAX1748 |
| 廠商： | Maxim Integrated Products, Inc. |
| 元件分類： | DC/DC變換器 |
| 英文描述： | Triple-Output TFT LCD DC-DC Converter |
| 中文描述： | 三輸出TFT-LCD DC-DC轉換器 |
| 文件頁數： | 8/16頁 |
| 文件大小： | 277K |
| 代理商： | MAX1748 |
M
Triple-Output TFT LCD DC-DC Converter
8
_______________________________________________________________________________________
Detailed Description
The MAX1748 is a highly efficient triple-output power
supply for TFT LCD applications. The device contains
one high-power step-up converter and two low-power
charge pumps. The primary boost converter uses an
internal N-channel MOSFET to provide maximum effi-
ciency and to minimize the number of external compo-
nents. The output voltage of the main boost converter
(V
MAIN
) can be set from V
IN
to 13V with external resistors.
The dual charge pumps independently regulate a posi-
tive output (V
POS
) and a negative output (V
NEG
). These
low-power outputs use external diode and capacitor
stages (as many stages as required) to regulate output
voltages up to +40V and down to -40V. A proprietary
regulation algorithm minimizes output ripple as well as
capacitor sizes for both charge pumps.
Also included in the MAX1748 are a precision 1.25V
reference that sources up to 50μA, logic shutdown,
soft-start, power-up sequencing, fault detection, and an
active-low open-drain ready output.
Main Boost Converter
The MAX1748 main step-up converter switches at a
constant 1MHz internal oscillator frequency to allow the
use of small inductors and output capacitors. The
MOSFET switch pulse width is modulated to control the
power transferred on each switching cycle and to regu-
late the output voltage.
During PWM operation, the internal clock
’
s rising edge
sets a flip-flop, which turns on the N-channel MOSFET
(Figure 1). The switch turns off when the sum of the
voltage-error, slope-compensation, and current-feed-
back signals trips the multi-input comparator and
resets the flip-flop. The switch remains off for the rest of
the clock cycle. Changes in the output voltage error
signal shift the switch current trip level, consequently
modulating the MOSFET duty cycle.
Dual Charge-Pump Regulator
The MAX1748 contains two individual low-power charge
pumps. One charge pump inverts the supply voltage
(SUPN) and provides a regulated negative output voltage.
The second charge pump doubles the supply voltage
(SUPP) and provides a regulated positive output voltage.
The MAX1748 contains internal P-channel and N-channel
MOSFETs to control the power transfer. The internal
MOSFETs switch at a constant 500kHz (0.5
f
OSC
).
Negative Charge Pump
During the first half-cycle, the P-channel MOSFET turns
on and the flying capacitor C5 charges to V
SUPN
minus
a diode drop (Figure 2). During the second half-cycle,
the P-channel MOSFET turns off, and the N-channel
MOSFET turns on, level shifting C5. This connects C5 in
parallel with the reservoir capacitor C6. If the voltage
across C6 minus a diode drop is lower than the voltage
across C5, charge flows from C5 to C6 until the diode
(D5) turns off. The amount of charge transferred to the
output is controlled by the variable N-channel on-resis-
tance.
Positive Charge Pump
During the first half-cycle, the N-channel MOSFET turns
on and charges the flying capacitor C3 (Figure 3). This
initial charge is controlled by the variable N-channel
on-resistance. During the second half-cycle, the N-
channel MOSFET turns off and the P-channel MOSFET
turns on, level shifting C3 by V
SUPP
volts. This connects
C3 in parallel with the reservoir capacitor C4. If the volt-
age across C4 plus a diode drop (V
POS
+ V
DIODE
) is
smaller than the level-shifted flying capacitor voltage
(V
C3
+ V
SUPP
), charge flows from C3 to C4 until the
diode (D3) turns off.
Soft-Start
For the main boost regulator, soft-start allows a gradual
increase of the internal current-limit level during startup
to reduce input surge currents. The MAX1748 divides
Pin Description (continued)
PIN
NAME
FUNCTION
13
SUPP
Positive Charge-Pump Driver Supply Voltage. Bypass to PGND with a 0.1
μ
F capacitor.
14
PGND
Power Ground. Connect to GND underneath the IC.
15
LX
Main Boost Regulator Power MOSFET N-Channel Drain. Connect output diode and output capacitor
as close to PGND as possible.
16
TGND
Must be connected to ground.
相關PDF資料 |
PDF描述 |
|---|---|
| MAX1748-MAX8726 | Triple-Output TFT-LCD DC-DC Converters |
| MAX1748EUE | Triple-Output TFT LCD DC-DC Converter |
| MAX1755AAUT-T | SOT23 Local Temperature Comparators with SMBus Serial Interface |
| MAX1755BAUT-T | SOT23 Local Temperature Comparators with SMBus Serial Interface |
| MAX1756BAUT-T | SOT23 Local Temperature Comparators with SMBus Serial Interface |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX17480EVKIT+ | 功能描述:電源管理IC開發工具 MAX17480 Eval Kit RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V |
| MAX17480GTL+ | 功能描述:顯示驅動器和控制器 2-/3-Output Mobile erial VID Ctlr RoHS:否 制造商:Panasonic Electronic Components 工作電源電壓:2.7 V to 5.5 V 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:QFN-44 封裝:Reel |
| MAX17480GTL+T | 功能描述:顯示驅動器和控制器 2-/3-Output Mobile erial VID Ctlr RoHS:否 制造商:Panasonic Electronic Components 工作電源電壓:2.7 V to 5.5 V 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:QFN-44 封裝:Reel |
| MAX17482GTL+ | 功能描述:電壓模式 PWM 控制器 NDA IC RoHS:否 制造商:Texas Instruments 輸出端數量:1 拓撲結構:Buck 輸出電壓:34 V 輸出電流: 開關頻率: 工作電源電壓:4.5 V to 5.5 V 電源電流:600 uA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 封裝 / 箱體:WSON-8 封裝:Reel |
| MAX17482GTL+T | 功能描述:電壓模式 PWM 控制器 NDA IC RoHS:否 制造商:Texas Instruments 輸出端數量:1 拓撲結構:Buck 輸出電壓:34 V 輸出電流: 開關頻率: 工作電源電壓:4.5 V to 5.5 V 電源電流:600 uA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 封裝 / 箱體:WSON-8 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。