參數資料
型號： MAX1739EEP
廠商： MAXIM INTEGRATED PRODUCTS INC
元件分類： 穩壓器
英文描述： Wide Brightness Range CCFL Backlight Controllers
中文描述： FLUORESCENT LIGHT CONTROLLER, 64 kHz SWITCHING FREQ-MAX, PDSO20
封裝： 0.150 INCH, 0.025 INCH PITCH, QSOP-20
文件頁數： 24/26頁
文件大?。?/td> 444K
代理商： MAX1739EEP
M
Wide Brightness Range
CCFL Backlight Controllers
24
______________________________________________________________________________________
Status Register
[STATUS1–STATUS0] (POR = 0b11)
The status register returns information on fault condi-
tions. If a lamp is not connected to the secondary of the
transformer, the MAX1739 will detect that the lamp cur-
rent has not exceeded the CSAV detection threshold
and after 2 seconds will clear the STATUS1 bit (see
Lamp-Out Detection
). The STATUS1 bit is latched; i.e.,
it will remain 0 even if the lamp-out condition goes
away. When STATUS1 = 0, the lamp is forced off. STA-
TUS0 reports 1 as long as no overcurrent conditions
are detected. If an overcurrent condition is detected in
any given DPWM period, STATUS0 is cleared for the
duration of the following DPWM period. If an overcur-
rent condition is not detected in any given DPWM peri-
od, STATUS0 is set for the duration of the following dig-
ital DPWM period. Forcing the CCFL lamp off by
entering shutdown, writing to the mode register, or by
toggling
SH
/SUS sets STATUS1.
ID Registers
The ID registers return information on the manufacturer,
the chip ID, and the chip revision number. The
MAX1739 is the first-generation advanced CCFL con-
troller, and its ChipRev is 0x00. Reading from the MfgID
register returns 0x4D, which is the ASCII code for
“
M
”
(for Maxim); the ChipID register returns 0x96. Writing to
these registers has no effect.
BIT
NAME
POR
STATE
DESCRIPTION
2
SHMD2
0
SHMD2 = 1 forces the lamp off and sets STATUS1. SHMD2 = 0 allows the lamp to operate, though it
may still be shut down by the
SH/
SUS pin (depending on the state of SHMD1 and SHMD0).
1
SHMD1
0
When
SH
/SUS = 0, this bit has no effect.
SH
/SUS = 1 and SHMD1 = 1 forces the lamp off and sets
STATUS1.
SH
/SUS = 1 and SHMD1 = 0 allow the lamp to operate, though it may still be shut down
by the SHMD2 bit.
0
SHMD0
1
When
SH
/SUS = 1, this bit has no effect.
SH
/SUS = 0 and SHMD0 = 1 forces the lamp off and sets
STATUS1.
SH
/SUS = 0 and SHMD0 = 0 allows the lamp to operate, though it may still be shut down
by the SHMD2 bit.
Table 7. SHMD Register Bit Descriptions
SH
/SUS
0
0
1
1
X
SHMD2
0
0
0
0
1
SHMD1
X
X
0
1
X
SHMD0
0
1
X
X
X
OPERATING MODE
Operate
Shutdown, STATUS1 set
Operate
Shutdown, STATUS1 set
Shutdown, STATUS1 set
Table 8.
SH
/SUS and SHMD Register Truth Table
BIT
NAME
POR
STATE
DESCRIPTION
1
STATUS1
1
STATUS1 = 0 means that a lamp-out condition has been detected. The STATUS1 bit stays clear
even after the lamp-out condition has gone away. The only way to set STATUS1 is to shut off the
lamp by programming the mode register or by toggling
SH
/SUS.
0
STATUS0
1
STATUS0 = 0 means that an overcurrent condition was detected during the previous digital PWM
period. STATUS0 = 1 means that no overcurrent condition was detected during the previous digital
PWM period.
Table 9. Status Register Bit Descriptions (Read Only/Writes Have No Effect)
X = Don
’
t care
相關PDF資料
PDF描述
MAX1839 Wide Brightness Range CCFL Backlight Controllers
MAX1839EEP Wide Brightness Range CCFL Backlight Controllers
MAX1740 Digital Signal Processors 144-LQFP
MAX1741 SIM/Smart Card Level Translators in レMAX
MAX1740EUB SIM/Smart Card Level Translators in レMAX
相關代理商/技術參數
參數描述
MAX1739EEP+ 功能描述:顯示驅動器和控制器 CCFL Backlight Controller RoHS:否 制造商:Panasonic Electronic Components 工作電源電壓:2.7 V to 5.5 V 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:QFN-44 封裝:Reel
MAX1739EEP+T 功能描述:顯示驅動器和控制器 CCFL Backlight Controller RoHS:否 制造商:Panasonic Electronic Components 工作電源電壓:2.7 V to 5.5 V 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:QFN-44 封裝:Reel
MAX1739EEP-T 功能描述:顯示驅動器和控制器 RoHS:否 制造商:Panasonic Electronic Components 工作電源電壓:2.7 V to 5.5 V 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:QFN-44 封裝:Reel
MAX1739EVKIT 功能描述:電源管理IC開發工具 MAX1739 Eval Kit RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V
MAX173BCNG 制造商:Maxim Integrated Products 功能描述:
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*