參數資料
型號： MAX1718BEEI
廠商： MAXIM INTEGRATED PRODUCTS INC
元件分類： 穩壓器
英文描述： Notebook CPU Step-Down Controller for Intel Mobile Voltage Positioning IMVP-II
中文描述： SWITCHING CONTROLLER, 1000 kHz SWITCHING FREQ-MAX, PDSO28
封裝： 0.150 INCH, 0.025 INCH PITCH, MO-137AD, QSOP-28
文件頁數： 10/35頁
文件大?。?/td> 700K
代理商： MAX1718BEEI
M
Notebook CPU Step-Down Controller for Intel
Mobile Voltage Positioning (IMVP-II)
10
______________________________________________________________________________________
Pin Description (continued)
Supply Voltage Input for the DL Gate Driver, 4.5V to 5.5V. Bypass to GND with a 1μF capacitor.
V
DD
17
Low-Side Gate Driver Output. DL swings GND to V
DD
.
DL
16
Analog and Power Ground. Also connects to the current-limit comparator.
GND
15
Open-Drain Power-Good Output. VGATE is normally high when the output is in regulation. If V
FB
is not within
a ±10% window of the DAC setting, VGATE is asserted low. During DAC code transitions, VGATE is forced
high until 1 clock period after the slew-rate controller finishes the transition. VGATE is low during shutdown.
VGATE
14
Feedback Offset Adjust Negative Input. The output shifts by an amount equal to the difference between POS
and NEG multiplied by a scale factor that depends on the DAC codes (see the
Integrator Amplifiers/Output
Voltage Offsets
section). Connect both POS and NEG to REF if the offset function is not used.
POS
13
Current-Limit Adjustment. The GND - LX current-limit threshold defaults to 100mV if ILIM is connected to
V
CC
. In adjustable mode, the current-limit threshold voltage is 1/10th the voltage seen at ILIM over a 0.5V to
3V range. The logic threshold for switchover to the 100mV default value is approximately V
CC
- 1V. Connect
ILIM to REF for a fixed 200mV threshold.
ILIM
12
2V Reference Output. Bypass to GND with 0.22μF (min) capacitor. Can source 50μA for external loads.
Loading REF degrades FB accuracy according to the REF load-regulation error.
REF
11
On-Time Selection Control Input. This is a four-level input that sets the K factor (Table 2) to determine
DH on-time. Connect TON to the following pins for the indicated operation:
GND = 1000kHz
REF = 550kHz
Open = 300kHz
V
CC
= 200kHz
TON
10
PIN
NAME
FUNCTION
Suspend-Mode Control Input. When SUS is high, the suspend-mode VID code, as programmed by S0 and
S1, is delivered to the DAC. Connect SUS to GND if the Suspend-mode multiplexer is not used (see the
Internal Multiplexers (ZMODE/SUS)
section).
SUS
18
Performance-Mode MUX Control Input. If SUS is low, ZMODE selects between two different VID DAC codes.
If ZMODE is low, the VID DAC code is set by the logic-level voltages on D0
–
D4. On the rising edge of
ZMODE, during power-up with ZMODE high, or on the falling edge of SUS when ZMODE is high, the VID
DAC code is determined by the impedance at D0
–
D4 (see the
Internal Multiplexers (ZMODE/SUS)
section).
ZMODE
19
Overvoltage Protection Control Input. Connect
OVP
low to enable overvoltage protection. Connect
OVP
high
to disable overvoltage protection. The overvoltage trip threshold is approximately 2V. The state of
OVP
does
not affect output undervoltage fault protection or thermal shutdown.
OVP
20
VID DAC Code Inputs. D0 is the LSB, and D4 is the MSB of the internal 5-bit VID DAC (Table 3). If ZMODE
is low, D0
–
D4 are high-impedance digital inputs, and the VID DAC code is set by the logic-level voltages on
D0
–
D4. On the rising edge of ZMODE, during power-up with ZMODE high, or on the falling edge of SUS
when ZMODE is high, the VID DAC code is determined by the impedance at D0
–
D4 as follows:
Logic low = source impedance is
≤
1k
+ 5%.
Logic high = source impedance is
≥
100k
- 5%.
D4
–
D0
21
–
25
Boost Flying Capacitor Connection. Connect BST to the external boost diode and capacitor as shown in
Figure 1. An optional resistor in series with BST allows the DH pullup current to be adjusted (Figure 8).
BST
26
Inductor Connection. LX is the internal lower supply rail for the DH high-side gate driver. It also connects to
the current-limit comparator and the skip-mode zero-crossing comparator.
LX
27
High-Side Gate-Driver Output. DH swings LX to BST.
DH
28
相關PDF資料
PDF描述
MAX1720EUTG Switched Capacitor Voltage Inverter with Shutdown
MAX1724EZK50 1.5uA IQ, Step-Up DC-DC Converters in Thin SOT23-5
MAX1724EZK30 1.5uA IQ, Step-Up DC-DC Converters in Thin SOT23-5
MAX1724EZK30-T 1.5uA IQ, Step-Up DC-DC Converters in Thin SOT23-5
MAX1724EZK33 1.5uA IQ, Step-Up DC-DC Converters in Thin SOT23-5
相關代理商/技術參數
參數描述
MAX1718BEEI+ 制造商:Maxim Integrated Products 功能描述:NOTEBOOK CPU STEP-DOWN CONTROLLER FOR INTEL MOBILE VOLTAGE - Rail/Tube
MAX1718BEEI-TG068 制造商:Rochester Electronics LLC 功能描述: 制造商:Maxim Integrated Products 功能描述:
MAX1718EEI 制造商:Maxim Integrated Products 功能描述:NOTEBOOK CPU STEP-DOWN CONTROLLER FOR INTEL M - Bulk
MAX1718EEI+ 制造商:Maxim Integrated Products 功能描述:LDO CNTRLR STDN 0.6V TO 1.75V 28QSOP - Rail/Tube
MAX1718EEI+T 制造商:Maxim Integrated Products 功能描述:LDO CNTRLR STDN 0.6V TO 1.75V 28QSOP - Tape and Reel
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*