- 您現在的位置：買賣IC網 > PDF目錄383333 > MAX1715 (Maxim Integrated Products, Inc.) Ultra-High Efficiency, Dual Step-Down Controller for Notebook Computers PDF資料下載
參數資料
| 型號： | MAX1715 |
| 廠商： | Maxim Integrated Products, Inc. |
| 英文描述： | Ultra-High Efficiency, Dual Step-Down Controller for Notebook Computers |
| 中文描述： | 超高效率、雙路降壓型控制器，用于筆記本電腦 |
| 文件頁數： | 17/28頁 |
| 文件大?。?/td> | 308K |
| 代理商： | MAX1715 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁當前第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁
M
Ultra-High Efficiency, Dual Step-Down
Controller for Notebook Computers
______________________________________________________________________________________
17
Overvoltage protection can be defeated through the
SKIP
test mode (Table 3).
Output Undervoltage Protection (UVP)
The output undervoltage protection function is similar to
foldback current limiting, but employs a timer rather
than a variable current limit. If the MAX1715 output volt-
age is under 70% of the nominal value 20ms after com-
ing out of shutdown, the PWM is latched off and won’t
restart until V
CC
power is cycled or
SHDN
is toggled.
No-Fault Test Mode
The over/undervoltage protection features can compli-
cate the process of debugging prototype breadboards
since there are (at most) a few milliseconds in which to
determine what went wrong. Therefore, a test mode is
provided to totally disable the OVP, UVP, and thermal
shutdown features, and clear the fault latch if it has
been set. The PWM operates as if
SKIP
were grounded
(PFM/PWM mode).
The no-fault test mode is entered by sinking 1.5mA
from
SKIP
through an external negative voltage source
in series with a resistor (Figure 7). SKIP is clamped to
AGND with a silicon diode, so choose the resistor value
equal to (V
FORCE
- 0.65V) / 1.5mA.
__________________Design Procedure
Firmly establish the input voltage range and maximum
load current before choosing a switching frequency
and inductor operating point (ripple-current ratio). The
primary design trade-off lies in choosing a good switch-
ing frequency and inductor operating point, and the fol-
lowing four factors dictate the rest of the design:
1)
Input voltage range.
The maximum value (V
IN(MAX)
)
must accommodate the worst-case high AC adapter
voltage. The minimum value (V
IN(MIN)
) must account
for the lowest battery voltage after drops due to con-
nectors, fuses, and battery selector switches. If
there is a choice at all, lower input voltages result in
better efficiency.
2)
Maximum load current.
There are two values to
consider. The
peak load current
(I
LOAD(MAX)
) deter-
mines the instantaneous component stresses and fil-
tering requirements, and thus drives output
capacitor selection, inductor saturation rating, and
the design of the current-limit circuit. The
continuous
load current
(I
LOAD
) determines the thermal stresses
and thus drives the selection of input capacitors,
MOSFETs, and other critical heat-contributing com-
ponents. Modern notebook CPUs generally exhibit
I
LOAD
= I
LOAD(MAX)
·
80%.
3)
Switching frequency.
This choice determines the
basic trade-off between size and efficiency. The
optimal frequency is largely a function of maximum
input voltage, due to MOSFET switching losses that
are proportional to frequency and V
IN
2. The opti-
mum frequency is also a moving target, due to rapid
improvements in MOSFET technology that are mak-
ing higher frequencies more practical (Table 4).
4)
Inductor operating point.
This choice provides
trade-offs between size vs. efficiency. Low inductor
values cause large ripple currents, resulting in the
smallest size, but poor efficiency and high output
noise. The minimum practical inductor value is one
that causes the circuit to operate at the edge of criti-
cal conduction (where the inductor current just
touches zero with every cycle at maximum load).
Inductor values lower than this grant no further size-
reduction benefit.
The MAX1715’s pulse-skipping algorithm initiates
skip mode at the critical conduction point. So, the
inductor operating point also determines the load-
current value at which PFM/PWM switchover occurs.
The optimum point is usually found between 20%
and 50% ripple current.
APPROXIMATELY
-0.65V
1.5mA
V
FORCE
SKIP
AGND
MAX1715
Figure 7. Disabling Over/Undervoltage Protection (Test Mode)
相關PDF資料 |
PDF描述 |
|---|---|
| MAX1715EEI | Ultra-High Efficiency, Dual Step-Down Controller for Notebook Computers |
| MAX1717 | Replaced by TMS320VC5506 : Digital Signal Processors 132-BQFP |
| MAX1717EEG | Replaced by TMS320VC5506 : Digital Signal Processors 100-LQFP |
| MAX1718EEI | Notebook CPU Step-Down Controller for Intel Mobile Voltage Positioning IMVP-II |
| MAX1718 | Replaced by TMS320VC5506 : Digital Signal Processors 100-LQFP -40 to 85 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX1715EEI | 功能描述:DC/DC 開關控制器 RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK |
| MAX1715EEI+ | 功能描述:DC/DC 開關控制器 Dual Step-Down Controller RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK |
| MAX1715EEI+T | 功能描述:DC/DC 開關控制器 Dual Step-Down Controller RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK |
| MAX1715EEI-T | 功能描述:DC/DC 開關控制器 RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK |
| MAX1715EVKIT | 功能描述:DC/DC 開關控制器 Evaluation Kit for the MAX1715 RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK |
發布緊急采購，3分鐘左右您將得到回復。