- 您現在的位置：買賣IC網 > PDF目錄383333 > MAX1714BEEE (MAXIM INTEGRATED PRODUCTS INC) High-Speed Step-Down Controller for Notebook Computers PDF資料下載
參數資料
| 型號： | MAX1714BEEE |
| 廠商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分類： | 穩壓器 |
| 英文描述： | High-Speed Step-Down Controller for Notebook Computers |
| 中文描述： | SWITCHING CONTROLLER, 600 kHz SWITCHING FREQ-MAX, PDSO16 |
| 封裝： | 0.150 INCH, 0.025 INCH PITCH, MO-137AA, QSOP-16 |
| 文件頁數： | 12/24頁 |
| 文件大小： | 443K |
| 代理商： | MAX1714BEEE |
M
High-Speed Step-Down Controller
for Notebook Computers
12
______________________________________________________________________________________
where K is set by the TON pin-strap connection and
0.075V is an approximation to accommodate for the
expected drop across the low-side MOSFET switch.
One-shot timing error increases for the shorter on-time
settings due to fixed propagation delays; it is approxi-
mately ±12.5% at 600kHz and 450kHz, and ±10% at the
two slower settings. This translates to reduced switching-
frequency accuracy at higher frequencies (Table 5).
Switching frequency increases as a function of load cur-
rent due to the increasing drop across the low-side
MOSFET, which causes a faster inductor-current dis-
charge ramp. The on-times guaranteed in the
Electrical
Characteristics
are influenced by switching delays in the
external high-side power MOSFET.
Two external factors that influence switching-frequency
accuracy are resistive drops in the two conduction loops
(including inductor and PC board resistance) and the
dead-time effect. These effects are the largest contribu-
tors to the change of frequency with changing load cur-
rent. The dead-time effect increases the effective
on-time, reducing the switching frequency as one or
both dead times are added to the effective on-time. It
occurs only in PWM mode (
SKIP
= high) when the induc-
tor current reverses at light or negative load currents.
With reversed inductor current, the inductor’s EMF caus-
es LX to go high earlier than normal, extending the on-
time by a period equal to the low-to-high dead time.
For loads above the critical conduction point, the actual
switching frequency is:
V
t
V
ON
IN
+
(
where V
DROP1
is the sum of the parasitic voltage drops
in the inductor discharge path, including synchronous
rectifier, inductor, and PC board resistances; V
DROP2
is
the sum of the resistances in the charging path, and t
ON
is the on-time calculated by the MAX1714.
Automatic Pulse-Skipping Switchover
In skip mode (
SKIP
low), an inherent automatic
switchover to PFM takes place at light loads. This
switchover is effected by a comparator that truncates the
low-side switch on-time at the inductor current’s zero
crossing. This mechanism causes the threshold between
pulse-skipping PFM and nonskipping PWM operation to
coincide with the boundary between continuous and dis-
continuous inductor-current operation (also known as the
“critical conduction” point; see the Continuous to
Discontinuous Inductor Current Point vs. Input Voltage
graph in the
Typical Operating Characteristics
). In low-
duty-cycle applications, this threshold is relatively con-
stant, with only a minor dependence on battery voltage.
where K is the on-time scale factor (Table 5). The load-
current level at which PFM/PWM crossover occurs,
I
LOAD(
SKIP
)
, is equal to 1/2 the peak-to-peak ripple cur-
rent, which is a function of the inductor value (Figure 3).
For example, in the standard application circuit with
K = 3.3μs (Table 5), V
OUT
= 2.5V, V
IN
= 15V, and L =
6.8μH, switchover to pulse-skipping operation occurs at
I
LOAD
= 0.51A or about 1/8 full load. The crossover point
occurs at an even lower value if a swinging (soft-satura-
tion) inductor is used.
The switching waveforms may appear noisy and asyn-
chronous when light loading causes pulse-skipping
operation, but this is a normal operating condition that
results in high light-load efficiency. Trade-offs in PFM
noise vs. light-load efficiency are made by varying the
inductor value. Generally, low inductor values produce a
broader efficiency vs. load curve, while higher values
result in higher full-load efficiency (assuming that the coil
resistance remains fixed) and less output voltage ripple.
Penalties for using higher inductor values include larger
physical size and degraded load-transient response
(especially at low input voltage levels).
DC output accuracy specifications refer to the error-com-
parator threshold of the error comparator. When the
inductor is in continuous conduction, the output voltage
will have a DC regulation level higher than the trip level
by 50% of the ripple. In discontinuous conduction (
SKIP
= AGND, light-loaded), the output voltage will have a DC
regulation level higher than the error-comparator thresh-
old by approximately 1.5% due to slope compensation.
Forced-PWM Mode (
SKIP
= High)
The low-noise forced-PWM mode (
SKIP
= high) disables
the zero-crossing comparator, which controls the low-
side switch on-time. This causes the low-side gate-drive
waveform to become the complement of the high-side
gate-drive waveform. This in turn causes the inductor
current to reverse at light loads while DH maintains a
duty factor of V
OUT
/V
IN
. The benefit of forced-PWM
mode is to keep the switching frequency fairly constant,
but it comes at a cost: the no-load battery current can be
10mA to 40mA, depending on the external MOSFETs.
Forced-PWM mode is most useful for reducing audio-
frequency noise, improving load-transient response, pro-
viding sink-current capability for dynamic output voltage
adjustment, and improving the cross-regulation of
I
KV
2L
V
-V
V
IN
LOAD(SKIP)
OUT
IN
OUT
≈
f
V
V
OUT
DROP
DROP
=
+
)
1
2
相關PDF資料 |
PDF描述 |
|---|---|
| MAX1715 | Ultra-High Efficiency, Dual Step-Down Controller for Notebook Computers |
| MAX1715EEI | Ultra-High Efficiency, Dual Step-Down Controller for Notebook Computers |
| MAX1717 | Replaced by TMS320VC5506 : Digital Signal Processors 132-BQFP |
| MAX1717EEG | Replaced by TMS320VC5506 : Digital Signal Processors 100-LQFP |
| MAX1718EEI | Notebook CPU Step-Down Controller for Intel Mobile Voltage Positioning IMVP-II |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX1714BEEE+ | 功能描述:電流型 PWM 控制器 Step-Down Controller for Notebook RoHS:否 制造商:Texas Instruments 開關頻率:27 KHz 上升時間: 下降時間: 工作電源電壓:6 V to 15 V 工作電源電流:1.5 mA 輸出端數量:1 最大工作溫度:+ 105 C 安裝風格:SMD/SMT 封裝 / 箱體:TSSOP-14 |
| MAX1714BEEE+T | 功能描述:電流型 PWM 控制器 Step-Down Controller for Notebook RoHS:否 制造商:Texas Instruments 開關頻率:27 KHz 上升時間: 下降時間: 工作電源電壓:6 V to 15 V 工作電源電流:1.5 mA 輸出端數量:1 最大工作溫度:+ 105 C 安裝風格:SMD/SMT 封裝 / 箱體:TSSOP-14 |
| MAX1714BEEE-T | 功能描述:電流型 PWM 控制器 RoHS:否 制造商:Texas Instruments 開關頻率:27 KHz 上升時間: 下降時間: 工作電源電壓:6 V to 15 V 工作電源電流:1.5 mA 輸出端數量:1 最大工作溫度:+ 105 C 安裝風格:SMD/SMT 封裝 / 箱體:TSSOP-14 |
| MAX1714BEEE-TG074 | 制造商:Rochester Electronics LLC 功能描述: 制造商:Maxim Integrated Products 功能描述: |
| MAX1714BEVKIT | 功能描述:電流型 PWM 控制器 Evaluation Kit for the MAX1714B RoHS:否 制造商:Texas Instruments 開關頻率:27 KHz 上升時間: 下降時間: 工作電源電壓:6 V to 15 V 工作電源電流:1.5 mA 輸出端數量:1 最大工作溫度:+ 105 C 安裝風格:SMD/SMT 封裝 / 箱體:TSSOP-14 |
發布緊急采購，3分鐘左右您將得到回復。