- 您現在的位置：買賣IC網 > PDF目錄383330 > MAX1654EEE (MAXIM INTEGRATED PRODUCTS INC) High-Efficiency, PWM, Step-Down DC-DC Controllers in 16-Pin QSOP PDF資料下載
參數資料
| 型號： | MAX1654EEE |
| 廠商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分類： | 穩壓器 |
| 英文描述： | High-Efficiency, PWM, Step-Down DC-DC Controllers in 16-Pin QSOP |
| 中文描述： | SWITCHING CONTROLLER, 350 kHz SWITCHING FREQ-MAX, PDSO16 |
| 封裝： | 0.150 INCH, 0.025 INCH PITCH, QSOP-16 |
| 文件頁數： | 20/28頁 |
| 文件大?。?/td> | 265K |
| 代理商： | MAX1654EEE |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁當前第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁
M
High-Effic ienc y, PWM, S tep-Down
DC-DC Controllers in 16-Pin QS OP
20
______________________________________________________________________________________
__________________Design Proc edure
The predesigned standard application circuits (Figure
1 and Table 1) contain ready-to-use solutions for com-
mon applications. Use the following design procedure
to optimize the basic schematic for different voltage or
current requirements. Before beginning a design, firmly
establish the following:
V
IN(MAX)
, the maximum input (battery) voltage.
This
value should include the worst-case conditions, such
as no-load operation when a battery charger or AC
adapter is connected but no battery is installed.
V
IN(MAX)
must not exceed 30V. This 30V upper limit is
determined by the breakdown voltage of the BST float-
ing gate driver to GND (36V absolute maximum).
V
IN(MIN)
, the minimum input (battery) voltage.
This
should be at full-load under the lowest battery condi-
tions. If V
IN(MIN)
is less than 4.5V, a special circuit must
be used to externally hold up VL above 4.8V. If the min-
imum input-output difference is less than 1V, the filter
capacitance required to maintain good AC load regula-
tion increases.
Induc tor V alue
The exact inductor value isn’t critical and can be
adjusted freely in order to make trade-offs among size,
cost, and efficiency. Although lower inductor values will
minimize size and cost, they will also reduce efficiency
due to higher peak currents. To permit use of the physi-
cally smallest inductor, lower the inductance until the
circuit is operating at the border between continuous
and discontinuous modes. Reducing the inductor value
even further, below this crossover point, results in dis-
continuous-conduction operation even at full load. This
helps reduce output filter capacitance requirements but
causes the core energy storage requirements to
increase again. On the other hand, higher inductor val-
ues will increase efficiency, but at some point resistive
losses due to extra turns of wire will exceed the benefit
gained from lower AC current levels. Also, high induc-
tor values affect load-transient response; see the V
SAG
equation in the Low-Voltage Operationsection.
The following equations are given for continuous-conduc-
tion operation since the MAX1652 family is mainly intend-
ed for high-efficiency, battery-powered applications. See
Appendix A in Maxim’s Battery Management and DC-DC
Converter Circuit Collection for crossover point and dis-
continuous-mode equations. Discontinuous conduction
doesn’t affect normal Idle Mode operation.
Three key inductor parameters must be specified:
inductance value (L), peak current (I
PEAK
), and DC
resistance (R
DC
). The following equation includes a
constant LIR, which is the ratio of inductor peak-to-peak
AC current to DC load current. A higher value of LIR
allows smaller inductance, but results in higher losses
and ripple. A good compromise between size and loss-
es is found at a 30% ripple current to load current ratio
(LIR = 0.3), which corresponds to a peak inductor cur-
rent 1.15 times higher than the DC load current.
V
OUT
(V
IN(MAX)
- V
OUT
)
L = ———————————
V
IN(MAX)
x f x I
OUT
x LIR
f = switching frequency, normally 150kHz or
300kHz
I
OUT
= maximum DC load current
LIR = ratio of AC to DC inductor current,
typically 0.3
The peak inductor current at full load is 1.15 x I
OUT
if
the above equation is used; otherwise, the peak current
can be calculated by:
where:
The inductor’s DC resistance is a key parameter for effi-
ciency performance and must be ruthlessly minimized,
preferably to less than 25m
at I
OUT
= 3A. If a stan-
dard off-the-shelf inductor is not available, choose a
core with an LI
2
rating greater than L x I
PEAK2
and wind
it with the largest diameter wire that fits the winding
area. For 300kHz applications, ferrite core material is
strongly preferred; for 150kHz applications, Kool-mu
(aluminum alloy) and even powdered iron can be
acceptable. If light-load efficiency is unimportant (in
desktop 5V-to-3V applications, for example) then low-
permeability iron-powder cores may be acceptable,
even at 300kHz. For high-current applications, shielded
core geometries (such as toroidal or pot core) help
keep noise, EMI, and switching-waveform jitter low.
Current-S ense Resistor V alue
The current-sense resistor value is calculated accord-
ing to the worst-case, low-current-limit threshold voltage
(from the Electrical Characteristics table) and the peak
inductor current. The continuous-mode peak inductor-
current calculations that follow are also useful for sizing
the switches and specifying the inductor-current satu-
ration ratings. In order to simplify the calculation, I
LOAD
may be used in place of I
PEAK
if the inductor value has
been set for LIR = 0.3 or less (high inductor values)
and 300kHz operation is selected. Low-inductance
resistors, such as surface-mount metal-film resistors,
are preferred.
80mV
R
SENSE
= ————
I
PEAK
I
I
x f x L x V
PEAK
LOAD
IN MAX
(
=
+
)
V
(V
- V
)
OUT
2
IN(MAX)
OUT
相關PDF資料 |
PDF描述 |
|---|---|
| MAX1658 | 350mA, 16.5V Input, Low-Dropout Linear Regulators |
| MAX1658ESA | 350mA, 16.5V Input, Low-Dropout Linear Regulators |
| MAX1659ESA | 350mA, 16.5V Input, Low-Dropout Linear Regulators |
| MAX165ACPN | CMOS レP-Compatible, 5レs, 8-Bit ADCs |
| MAX166DCPP | CMOS レP-Compatible, 5レs, 8-Bit ADCs |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX1654EEE+ | 功能描述:DC/DC 開關控制器 PWM Step-Down RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK |
| MAX1654EEE+T | 功能描述:DC/DC 開關控制器 PWM Step-Down RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK |
| MAX1654EEE-T | 功能描述:DC/DC 開關控制器 PWM Step-Down RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK |
| MAX1655EEE | 功能描述:DC/DC 開關控制器 PWM Step-Down RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK |
| MAX1655EEE+ | 功能描述:DC/DC 開關控制器 PWM Step-Down RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK |
發布緊急采購，3分鐘左右您將得到回復。