- 您現在的位置：買賣IC網 > PDF目錄383330 > MAX1647EAP (MAXIM INTEGRATED PRODUCTS INC) Chemistry-Independent Battery Chargers PDF資料下載
參數資料
| 型號： | MAX1647EAP |
| 廠商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分類： | 電源管理 |
| 英文描述： | Chemistry-Independent Battery Chargers |
| 中文描述： | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO20 |
| 封裝： | 5.30 MM, MO-150, SSOP-20 |
| 文件頁數： | 17/24頁 |
| 文件大?。?/td> | 161K |
| 代理商： | MAX1647EAP |
Each communication with the MAX1647 begins with a
start condition that is defined as a falling edge on SDA
with SCL high. The device address follows the start
condition. The MAX1647 device address is 0b0001001
(0b indicates a binary number), which may also be
denoted as 0x12 (0x indicates a hexadecimal number)
for Write-Word commands, or 0x13 in hexadecimal for
Read-Word commands (note that the address is only
seven bits, and the hexadecimal representation uses
R/
W
as its least significant bit).
ChargerMode( )
The ChargerMode( ) command uses Write-Word proto-
col. The command code for ChargerMode( ) is 0x12;
thus the CMD7–CMD0 bits in Write-Word protocol
should be 0b00010010. Table 2 describes the functions
of the 16 different data bits (D0–D15). Bit 0 refers to the
D0 bit in the Write-Word protocol (Figure 7).
Whenever the BATTERY_PRESENT status bit is clear,
the HOT_STOP bit is set, regardless of any previous
ChargerMode( ) command. To charge a battery that
has a thermistor impedance in the HOT range (i.e.,
THERMISTOR_HOT = 1 and THERMISTOR_UR = 0),
the host must use the ChargerMode( ) command to
clear HOT_STOP
after
the battery is inserted. The
HOT_STOP bit returns to its default power-up condition
(‘1’) whenever the battery is removed.
ChargingVoltage( )
The ChargingVoltage( ) command uses Write-Word
protocol. The command code for ChargingVoltage( ) is
0x15; thus, the CMD7–CMD0 bits in Write-Word proto-
col should be 0b00010101. The 16-bit binary number
formed by D15–D0 represents the voltage set point
(V0) in millivolts; however, since the MAX1647 has only
16mV resolution in setting V0, the D0, D1, D2, and D3
bits are ignored. For D15 = D14 = 0:
In equation 1, VDAC is the decimal equivalent of the
binary number represented by bits D13, D12, D11,
D10, D9, D8, D7, D6, D5, and D4 programmed with the
ChargingVoltage( ) command. For example, if D4–D13
are all set, VDAC is the decimal equivalent of
0b1111111111 (1023). If either D15 or D14, or both
D15 and D14, are set, all the bits in the voltage DAC
(Figure 6a) are set, regardless of D13–D0, and the
status register’s VOLTAGE_OR bit is set. For D15 = 1
and/or D14 = 1:
M
Chemistry-Independent
Battery Chargers
______________________________________________________________________________________
17
Table 2. ChargerMode( ) Bit Functions
1
6
POWER_FAIL_MASK
0
5
—
4, 7, 8, 9,
11–15
N/A
BATTERY_PRESENT_MASK
1
10
HOT_STOP
—
2
POR_RESET
—
1
0
0
INHIBIT_CHARGE
ENABLE_POLLING
—
3
RESET_TO_ZERO
POR
VALUE**
BIT
POSITION*
BIT NAME
0 = Interrupt on either edge of the POWER_FAIL status bit.
1 = Do not interrupt because of a POWER_FAIL bit change.
0 = Interrupt on either edge of the BATTERY_PRESENT status bit.
1 = Do not interrupt because of a BATTERY_PRESENT bit change.
Not implemented. Write 1 into this bit.
0 = The THERMISTOR_HOT status bit does not turn the charger off.
1 = THERMISTOR_HOT turns the charger off.
0 = No change in any non-ChargerMode( ) settings.
1 = Change the voltage and current settings to 0xFFFF and 0x00C0
respectively; clear the THERMISTOR_HOT and ALARM_INHIBITED bits.
Not implemented. Write 0 into this bit.
0 = Allow normal operation; clear the CHG_INHIBITED status bit.
1 = Turn the charger off; set the CHG_INHIBITED status bit.
Not implemented. Write 0 into this bit.
FUNCTION
*Bit position in the D15–D0 data.
N/A = Not available.
**Power-on reset value.
VOLTAGE_OR = 0 and V0 in Volts = 4 x REF xVDAC
2
10
VOLTAGE_OR = 1 and V0 in Volts = 4 x REF x2
-1
2
10
10
相關PDF資料 |
PDF描述 |
|---|---|
| MAX1649CSA | 5V/3.3V or Adjustable, High-Efficiency, Low-Dropout, Step-Down DC-DC Controllers |
| MAX1651 | 5V/3.3V or Adjustable, High-Efficiency, Low-Dropout, Step-Down DC-DC Controllers |
| MAX1649EPA | 5V/3.3V or Adjustable, High-Efficiency, Low-Dropout, Step-Down DC-DC Controllers |
| MAX1649ESA | Circular Connector; Body Material:Aluminum Alloy; Series:D38999; No. of Contacts:100; Connector Shell Size:23; Connecting Termination:Grounded; Gender:Male |
| MAX1649 | 5V/3.3V or Adjustable, High-Efficiency,Low-Dropout, Step-Down DC-DC Controllers(5V或可調,降壓型，輸出電流2A,DC-DC變換器,MAX649的改進型) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX1647EAP+ | 功能描述:電池管理 RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel |
| MAX1647EAP+T | 制造商:Maxim Integrated Products 功能描述:CHGR MULTI-CHEM 4A 18V 20SSOP - Tape and Reel |
| MAX1647EAP-T | 制造商:Maxim Integrated Products 功能描述:CHEMISTRY-INDEPENDENT BATTERY CHARGERS - Tape and Reel |
| MAX1648ESE | 功能描述:電池管理 RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel |
| MAX1648ESE+ | 功能描述:電池管理 RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。