- 您現在的位置：買賣IC網 > PDF目錄383329 > MAX1645BEEI (MAXIM INTEGRATED PRODUCTS INC) Advanced Chemistry-Independent, Level 2 Battery Charger with Input Current Limiting PDF資料下載
參數資料
| 型號： | MAX1645BEEI |
| 廠商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分類： | 電源管理 |
| 英文描述： | Advanced Chemistry-Independent, Level 2 Battery Charger with Input Current Limiting |
| 中文描述： | 2-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO28 |
| 封裝： | QSOP-28 |
| 文件頁數： | 26/32頁 |
| 文件大?。?/td> | 357K |
| 代理商： | MAX1645BEEI |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁當前第26頁第27頁第28頁第29頁第30頁第31頁第32頁
M
Advanced Chemistry-Independent, Level 2
Battery Charger with Input Current Limiting
26
______________________________________________________________________________________
Load and Source Switch Drivers
The MAX1645B can drive two P-channel MOSFETs to
eliminate voltage drops across the Schottky diodes,
which are normally used to switch the load current from
the battery to the main DC source:
The source switch P1 is controlled by PDS. This P-
channel MOSFET is turned on when CVS rises to
300mV above BATT and turns off when CVS falls to
100mV above BATT. The same signal that controls
the PDS also sets the POWER_FAIL bit in the
Charger Status() register. See
Operating Conditions
.
Load switch P2 is controlled by PDL. This P-channel
MOSFET is turned off when the CVS rises to 100mV
below BATT and turns on when CVS falls to 300mV
below BATT.
Dropout Operation
The MAX1645B has a 99.99% duty-cycle capability
with a 10ms maximum on-time and 1μs off-time. This
allows the charger to achieve dropout performance lim-
ited only by resistive losses in the DC-DC converter
components (P1, R1, N1, R2; see Figure 1). The actual
dropout voltage is limited to 300mV between CVS and
BATT by the power-fail comparator (see
Operating
Conditions
).
Applications Information
Smart Battery Charging
System/Background Information
A smart battery charging system, at a minimum, con-
sists of a smart battery and smart battery charger com-
patible with the Smart Battery System Specifications
using the SMBus.
A system can use one or more smart batteries. Figure 10
shows a single-battery system. This configuration is
typically found in notebook computers, video cameras,
cellular phones, or other portable electronic equipment.
Another configuration uses two or more smart batteries
(Figure 11). The smart battery selector is used either to
connect batteries to the smart battery charger or the
system, or to disconnect them, as appropriate. For
each battery, three connections must be made: power
(the battery
’
s positive and negative terminals), the
SMBus (clock and data), and the safety signal (resis-
tance, typically temperature dependent). Additionally,
the system host must be able to query any battery so it
can display the state of all batteries present in the system.
Figure 11 shows a two-battery system where battery 2 is
being charged while battery 1 is powering the system.
This configuration can be used to
“
condition
”
battery 1,
allowing it to be fully discharged prior to recharge.
1000
100
10
R
)
1
0.1
-40
-50
-30 -20 -10 0 10 20 30 40 50 60 70 80 90 100 110
TEMPERATURE (
°
C)
Figure 9. Typical Thermistor Characteristics
Table 7. Thermistor Bit Settings
*
See Battery Present in the Operating Conditions section for more information.
THERMISTOR
STATUS BIT
DESCRIPTION
WAKE-UP CHARGE
CONTROLLED
CHARGE
RES_UR and RES_HOT
RES_HOT
(None)
Underrange
Hot
Normal
Allowed for timeout period
Not allowed
Allowed for timeout period
Allowed
Not allowed
Allowed
RES_COLD
Cold
Allowed for timeout
period
Allowed
RES_OR and RES_COLD
Overrange
Float charge*
Not allowed
相關PDF資料 |
PDF描述 |
|---|---|
| MAX1647 | Chemistry-Independent Battery Chargers |
| MAX1648 | Chemistry-Independent Battery Chargers |
| MAX1647-MAX1648 | Chemistry-Independent Battery Chargers |
| MAX1648ESE | Chemistry-Independent Battery Chargers |
| MAX1647EAP | Chemistry-Independent Battery Chargers |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX1645BEEI+ | 功能描述:電池管理 RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel |
| MAX1645BEEI+T | 功能描述:電池管理 RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel |
| MAX1645BEEI-T | 功能描述:電池管理 Advanced Chemistry-Independent Level 2 Battery Charger with Input Current Limiting RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel |
| MAX1645BEVKIT | 制造商:Maxim Integrated Products 功能描述:EVALUATION KIT/EVALUATION SYSTEM FOR THE MAX1645B - Bulk |
| MAX1645BEVKIT+ | 制造商:Maxim Integrated Products 功能描述:MAX1645B EVAL KIT+ - Boxed Product (Development Kits) |
發布緊急采購，3分鐘左右您將得到回復。