- 您現在的位置：買賣IC網 > PDF目錄383329 > MAX1631CAI (MAXIM INTEGRATED PRODUCTS INC) Multi-Output, Low-Noise Power-Supply Controllers for Notebook Computers PDF資料下載
參數資料
| 型號： | MAX1631CAI |
| 廠商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分類： | 穩壓器 |
| 英文描述： | Multi-Output, Low-Noise Power-Supply Controllers for Notebook Computers |
| 中文描述： | DUAL SWITCHING CONTROLLER, 300 kHz SWITCHING FREQ-MAX, PDSO28 |
| 封裝： | 5.30 MM, 0.65 MM PITCH, SSOP-28 |
| 文件頁數： | 23/28頁 |
| 文件大小： | 237K |
| 代理商： | MAX1631CAI |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁當前第23頁第24頁第25頁第26頁第27頁第28頁
M
Multi-Output, Low-Noise Power-S upply
Controllers for Notebook Computers
______________________________________________________________________________________
23
where t
D
is the diode-conduction time (120ns typical)
and V
FWD
is the forward voltage of the diode.
This power is dissipated in the MOSFET body diode if
no external Schottky diode is used.
where I
RMS
is the input ripple current as calculated in the
Design Procedure and Input Capacitor Value sections.
Light-Load Effic ienc y Considerations
Under light loads, the PWM operates in discontinuous
mode, where the inductor current discharges to zero at
some point during the switching cycle. This makes the
inductor current’s AC component high compared to the
load current, which increases core losses and I
2
R loss-
es in the output filter capacitors. For best light-load effi-
ciency, use MOSFETs with moderate gate-charge
levels, and use ferrite, MPP, or other low-loss core
material. Avoid powdered-iron cores; even Kool-Mu
(aluminum alloy) is not as good as ferrite.
PC Board Layout Considerations
Good PC board layout is required in order to achieve
specified noise, efficiency, and stability performance.
The PC board layout artist must be given explicit
instructions, preferably a pencil sketch showing the
placement of power-switching components and high-
current routing. See the PC board layout in the
MAX1630 Evaluation Kit manual for examples. A
ground plane is essential for optimum performance. In
most applications, the circuit will be located on a multi-
layer board, and full use of the four or more copper lay-
ers is recommended. Use the top layer for high-current
connections, the bottom layer for quiet connections
(REF, SS, GND), and the inner layers for an uninterrupt-
ed ground plane. Use the following step-by-step guide:
1) Place the high-power components (Figure1, C1, C3,
Q1, Q2, D1, L1, and R1) first, with any grounded
connections adjacent.
Priority 1:
Minimize current-sense resistor trace
lengths
and ensure accurate current
sensing with Kelvin connections (Figure 7).
Priority 2:
Minimize ground trace lengths
in the
high-current paths (discussed below).
Priority 3: Minimize other trace lengths in the high-
current paths.
Use >5mm-wide traces
C
IN
to high-side MOSFET drain: 10mm
max length
Rectifier diode cathode to low-side
MOSFET: 5mm max length
LX node (MOSFETs, rectifier cathode,
inductor): 15mm max length
Ideally, surface-mount power components are butted
up to one another with their ground terminals almost
touching. These high-current grounds are then con-
nected to each other with a wide filled zone of top-layer
copper so they don’t go through vias. The resulting top-
layer “sub-ground-plane” is connected to the normal
inner-layer ground plane at the output ground termi-
nals, which ensures that the IC’s analog ground is
sensing at the supply’s output terminals without interfer-
ence from IR drops and ground noise. Other high-
current paths should also be minimized, but
focusing
primarily on short ground and current-sense con-
nections eliminates about 90% of all PC board lay-
out problems
(see the PC board layouts in the
MAX1630 Evaluation Kit manual for examples).
2) Place the IC and signal components. Keep the main
switching nodes (LX nodes) away from sensitive
analog components (current-sense traces and REF
capacitor). Place the IC and analog components on
the opposite side of the board from the power-
switching node.
Important:
the IC must be no far-
ther than 10mm from the current-sense resistors.
Keep the gate-drive traces (DH_, DL_, and BST_)
shorter than 20mm and route them away from CSH_,
CSL_, and REF.
3) Use a single-point star ground where the input
ground trace, power ground (sub-ground-plane),
and normal ground plane meet at the supply’s out-
put ground terminal. Connect both IC ground pins
and all IC bypass capacitors to the normal ground
plane.
P(cap) = input capacitor ESR loss = (I
) x R
RMS
ESR
MAX1630
SENSE RESISTOR
HIGH CURRENT PATH
Figure 7. Kelvin Connections for the Current-Sense Resistors
相關PDF資料 |
PDF描述 |
|---|---|
| MAX1631EAI | Multi-Output, Low-Noise Power-Supply Controllers for Notebook Computers |
| MAX1632 | Multi-Output, Low-Noise Power-Supply Controllers for Notebook Computers |
| MAX1632CAI | Multi-Output, Low-Noise Power-Supply Controllers for Notebook Computers |
| MAX1633CAI | Multi-Output, Low-Noise Power-Supply Controllers for Notebook Computers |
| MAX1633EAI | Multi-Output, Low-Noise Power-Supply Controllers for Notebook Computers |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX1631CAI+ | 功能描述:DC/DC 開關控制器 RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK |
| MAX1631CAI+T | 功能描述:DC/DC 開關控制器 RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK |
| MAX1631CAI-T | 功能描述:DC/DC 開關控制器 RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK |
| MAX1631EAI | 功能描述:DC/DC 開關控制器 RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK |
| MAX1631EAI+ | 功能描述:DC/DC 開關控制器 Multi-Out Low-Noise Power-Supply Ctlr RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK |
發布緊急采購，3分鐘左右您將得到回復。