- 您現在的位置：買賣IC網 > PDF目錄383327 > MAX16033 (Maxim Integrated Products, Inc.) Low-Power Battery Backup Circuits in Small レDFN Packages PDF資料下載
參數資料
| 型號： | MAX16033 |
| 廠商： | Maxim Integrated Products, Inc. |
| 英文描述： | Low-Power Battery Backup Circuits in Small レDFN Packages |
| 中文描述： | 低功耗電池備份電路，采用微型µDFN封裝 |
| 文件頁數： | 9/21頁 |
| 文件大?。?/td> | 228K |
| 代理商： | MAX16033 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁當前第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁
M
Low-Power Battery Backup
Circuits in Small μDFN Packages
_______________________________________________________________________________________
9
Detailed Description
The Typical Operating Circuit shows a typical connec-
tion for the MAX16033–MAX16040. OUT powers the
static random-access memory (SRAM). If V
CC
is
greater than the reset threshold (V
TH
), or if V
CC
is lower
than V
TH
but higher than V
BATT
, V
CC
is connected to
OUT. If V
CC
is lower than V
TH
and V
CC
is less than
V
BATT
, BATT is connected to OUT. OUT supplies up to
200mA from V
CC
. In battery-backup mode, an internal
MOSFET connects the backup battery to OUT. The on-
resistance of the MOSFET is a function of the backup-
battery voltage and temperature and is shown in the
BATT-to-OUT On-Resistance vs. Temperature graph in
the Typical Operating Characteristics
Chip-Enable Signal Gating
(MAX16033–MAX16036 Only)
The MAX16033–MAX16036 provide internal gating of
chip-enable (
CE
) signals to prevent erroneous data
from being written to CMOS RAM in the event of a
power failure or brownout condition. During normal
operation, the
CE
gate is enabled and passes all
CE
transitions. When reset asserts, this path becomes
disabled, preventing erroneous data from corrupting
the CMOS RAM. The MAX16033–MAX16036 provide a
series transmission gate from
CE
IN to
CE
OUT. A 2ns
(typ) propagation delay from
CE
IN to
CE
OUT allows
these devices to be used with most μPs and high-
speed DSPs.
When
RESET
is deasserted,
CE
IN is connected to
CE
OUT through a low on-resistance transmission gate.
If
CE
IN is high when
RESET
is asserted,
CE
OUT
remains high regardless of any subsequent transitions
on
CE
IN during the reset event.
If
CE
IN is low when
RESET
is asserted,
CE
OUT is held
low for 1μs to allow completion of the read/write opera-
tion (Figure 1). After the 1μs delay expires,
CE
OUT
goes high and stays high regardless of any subsequent
transitions on
CE
IN during the reset event. When
CE
OUT is disconnected from
CE
IN,
CE
OUT is actively
pulled up to OUT.
The propagation delay through the chip-enable circuit-
ry depends on both the source impedance of the drive
to
CE
IN and the capacitive loading at
CE
OUT. The
chip-enable propagation delay is specified from the
50% point of
CE
IN to the 50% point of
CE
OUT, using a
50
driver and 50pF load capacitance. Minimize the
capacitive load at
CE
OUT and use a low output-imped-
ance driver to minimize propagation delay.
In high-impedance mode, the leakage current at
CE
IN
is ±1μA (max) over temperature. In low-impedance
mode, the impedance of
CE
IN appears as a 75
resis-
tor in series with the load at
CE
OUT.
V
CC
V
TH
t
RD
t
RD
t
RP
t
RP
CEIN
CEOUT
RESET
PFO
PFI > V
PFI
RESET-TO-CEOUT DELAY
*
*
IF CEIN GOES HIGH BEFORE RESET ASSERTS,
CEOUT GOES HIGH WITHOUT DELAY AS CEIN GOES HIGH.
Figure 1.
RESET
and Chip-Enable Timing
相關PDF資料 |
PDF描述 |
|---|---|
| MAX16034 | Low-Power Battery Backup Circuits in Small レDFN Packages |
| MAX16035 | Low-Power Battery Backup Circuits in Small レDFN Packages |
| MAX16036 | Low-Power Battery Backup Circuits in Small レDFN Packages |
| MAX16038 | Low-Power Battery Backup Circuits in Small レDFN Packages |
| MAX16039 | Low-Power Battery Backup Circuits in Small レDFN Packages |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX16033LLB23+ | 制造商:Maxim Integrated Products 功能描述:VOLT SUPERVISOR MONITOR 2.32V 10PIN UDFN - Rail/Tube |
| MAX16033LLB23+T | 功能描述:監控電路 Battery Backup 2.5V-Ep RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲（典型值）:10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel |
| MAX16033LLB26+ | 制造商:Maxim Integrated Products 功能描述:VOLT SUPERVISOR MONITOR 2.63V 10PIN UDFN - Rail/Tube |
| MAX16033LLB26+T | 功能描述:監控電路 Battery Backup 3.3V-Ep RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲（典型值）:10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel |
| MAX16033LLB29+ | 制造商:Maxim Integrated Products 功能描述:VOLT SUPERVISOR MONITOR 2.93V 10PIN UDFN - Rail/Tube |
發布緊急采購，3分鐘左右您將得到回復。