參數資料
型號： MAX1586AETM
廠商： MAXIM INTEGRATED PRODUCTS INC
元件分類： 電源管理
英文描述： High-Efficiency, Low-IQ PMICs with Dynamic Core for PDAs and Smart Phones
中文描述： 1-CHANNEL POWER SUPPLY SUPPORT CKT, QCC48
封裝： 7 X 7 MM, TQFN-48
文件頁數： 20/32頁
文件大?。?/td> 656K
代理商： MAX1586AETM
M
High-Efficiency, Low-I
Q
PMICs with
Dynamic Core for PDAs and Smart Phones
20
______________________________________________________________________________________
out of regulation, V7 is sourced from BKBT by a second
on-chip MOSFET. V7 can supply loads up to 30mA. V7
is intended to connect to VCC_BATT on Intel CPUs.
Due to variations in system implementation, BKBT and
V7 can be utilized in different ways. See the
Backup-
Battery Configurations
section for information on how to
use BKBT and V7.
Quiescent Operating Current
in Various States
The MAX1586/MAX1587 are designed for optimum effi-
ciency and minimum operating current for all typical
operating modes, including sleep and deep sleep.
These states are outlined in Table 1.
Voltage Monitors, Reset, and
Undervoltage-Lockout Functions
Undervoltage Lockout
When the input voltage is below 2.35V (typ), an under-
voltage-lockout (UVLO) circuit disables the IC. The
inputs remain high impedance while in UVLO, reducing
battery load under this condition. All serial registers are
maintained with the input voltage down to at least 2.35V.
Reset Output
(RSO)
and
MR
Input
The reset output (
RSO
) is low when the
MR
input is low
or when V7 is below 2.425V. V7 is powered from V1
(when enabled) or the backup-battery input (BKBT).
RSO
normally goes low:
1) When power is first applied in configurations with
no separate backup battery (external diode from
IN to BKBT).
2) When power is removed in configurations with no
separate backup battery (external diode from IN
to BKBT).
3) If the backup battery falls below 2.425V when V1
is off or out of regulation.
4) When the manual reset button is pressed (
MR
goes low).
RSO
has a timer that delays release until 65ms after V7
exceeds 2.3V when V
IN
> 2.4V. If V
IN
< 2.4V when V7
exceeds 2.3V,
RSO
deasserts immediately with no 65ms
delay. There is no delay in this case because the timer
circuitry is deactivated to minimize operating current dur-
ing IN undervoltage lockout.
RSO
is not triggered by any
output besides V7. If BKBT is not powered,
RSO
does
not function and is high impedance.
MR
is a manual reset input for hardware reset. When
MR
goes low,
RSO
asserts for a minimum of 65ms.
MR
does
not reset any internal MAX1586/MAX1587 functions.
Dead-Battery and Low-Battery Comparators—
DBI, LBI (MAX1586 only)
The DBI and LBI inputs monitor input power (usually a
battery) and trigger the
DBO
and
LBO
outputs. The
dead-battery comparator triggers
DBO
when the battery
(V
IN
) discharges to the dead-battery threshold. The
factory-set 3.15V threshold is selected by connecting
DBI to IN, or the threshold can be programmed with a
resistor-divider at DBI. The low-battery comparator has
a factory-set 3.6V threshold that is selected by connect-
ing LBI to IN, or its threshold can be programmed with a
resistor-divider at LBI.
One three-resistor-divider can set both DBI and LBI
(R1, R2, and R3 in Figure 2) according to the following
equations:
1) Choose R3 to be less than 250k
2) R1 = R3 V
LB
(1 - (1.232 / V
DB
))
3) R2 = R3 (1.232 x (V
LB
/ V
DB
) - 1)
where V
LB
is the low-battery threshold and V
DB
is the
dead-battery threshold.
Alternately, LBI and DBI can be set with separate two-
resistor-dividers. Choose the lower resistor of the divider
chain to be 250k
or less (R5 and R7 in Figure 3). The
equations for upper divider-resistors as a function of
each threshold are then:
R4 = R5 (V
DB
/ 1.232) - 1)
R6 = R7 (V
LB
- 1)
When resistors are used to set V
LB
, the threshold at LBI
is 1.00V. When resistors are used to set V
DB
, the
threshold at DBI is 1.232V. A resistor-set threshold can
MAX1586
MAIN BATTERY
R1
438k
R2
62k
R3
200k
IN
DBI (1.232V THRESHOLD)
LBI (1.00V THRESHOLD)
Figure 2. Setting the Low-Battery and Dead-Battery Thresholds
with One Resistor Chain. The values shown set a DBI threshold
of 3.3V and an LBI threshold of 3.5V (no resistors are needed
for the factory preset thresholds).
相關PDF資料
PDF描述
MAX1586 High-Efficiency, Low-IQ PMICs with Dynamic Core for PDAs and Smart Phones
MAX1587 High-Efficiency, Low-IQ PMICs with Dynamic Core for PDAs and Smart Phones
MAX1587AETL High-Efficiency, Low-IQ PMICs with Dynamic Core for PDAs and Smart Phones
MAX1586BETM High-Efficiency, Low-IQ PMICs with Dynamic Core for PDAs and Smart Phones
MAX1589A Low-Input-Voltage, 500mA LDO Regulator with RESET in SOT and TDFN
相關代理商/技術參數
參數描述
MAX1586AETM+ 功能描述:直流/直流開關調節器 PMICs w/Dynamic Core for PDAs RoHS:否 制造商:International Rectifier 最大輸入電壓:21 V 開關頻率:1.5 MHz 輸出電壓:0.5 V to 0.86 V 輸出電流:4 A 輸出端數量: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:PQFN 4 x 5
MAX1586AETM+T 功能描述:直流/直流開關調節器 PMICs w/Dynamic Core for PDAs RoHS:否 制造商:International Rectifier 最大輸入電壓:21 V 開關頻率:1.5 MHz 輸出電壓:0.5 V to 0.86 V 輸出電流:4 A 輸出端數量: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:PQFN 4 x 5
MAX1586AETM-T 功能描述:直流/直流開關調節器 PMICs w/Dynamic Core for PDAs RoHS:否 制造商:International Rectifier 最大輸入電壓:21 V 開關頻率:1.5 MHz 輸出電壓:0.5 V to 0.86 V 輸出電流:4 A 輸出端數量: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:PQFN 4 x 5
MAX1586AEVCMAXQU 功能描述:電源管理IC開發工具 MAX1586A Evaluation Kit/Evaluation System RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V
MAX1586AEVKIT 功能描述:電源管理IC開發工具 MAX1586A Evaluation Kit/Evaluation System RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*