- 您現在的位置：買賣IC網 > PDF目錄383327 > MAX1586 (Maxim Integrated Products, Inc.) High-Efficiency, Low-IQ PMICs with Dynamic Core for PDAs and Smart Phones PDF資料下載
參數資料
| 型號： | MAX1586 |
| 廠商： | Maxim Integrated Products, Inc. |
| 英文描述： | High-Efficiency, Low-IQ PMICs with Dynamic Core for PDAs and Smart Phones |
| 中文描述： | 高效率，低智商與動態的PDA和智能手機PMIC的核心 |
| 文件頁數： | 19/32頁 |
| 文件大?。?/td> | 656K |
| 代理商： | MAX1586 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁當前第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁
M
High-Efficiency, Low-I
Q
PMICs with
Dynamic Core for PDAs and Smart Phones
______________________________________________________________________________________
19
enable the sleep LDOs, drive
SLP
low. When
SLP
is high,
the switching step-down converters are active. The output
voltage of the sleep LDOs is set to be the same as the
switching step-down converters as described in the
Setting the Output Voltages
section. SLPIN is the input to
the V1 and V2 sleep LDOs and must connect to IN.
V3 (VCC_CORE) Step-Down
DC-DC Converter
V3 is a 1MHz current-mode step-down converter that
supplies loads up to 500mA. The V3 output voltage is set
by the I
2
C serial interface to between 0.7V and 1.475V in
25mV increments. The default voltage on power-up is
1.3V. See the
Serial Interface
section for details.
Forced PWM on REG3
Under moderate to heavy loading, the V3 always operates
in a low-noise PWM mode with constant frequency and
modulated pulse width. Switching harmonics generated by
fixed-frequency operation are consistent and easily filtered.
With light loads (<30mA) and PWM3 low, V3 operates
in an enhanced-efficiency Idle Mode during which the
converter switches only as needed to service the load.
With PWM3 high, V3 operates in low-noise forced-PWM
mode under all load conditions.
Linear Regulators (V4, V5, and V6)
V4 (VCC_PLL)
V4 is a linear regulator that provides a fixed 1.3V output
and supplies loads up to 35mA. The power input for the
V4 and V5 linear regulators is IN45, which is typically
connected to V2. To enable V4 on the MAX1587, drive
ON4 high, or drive ON4 low for shutdown. On the
MAX1586, the enable pins for V4 and V5 are combined.
Drive ON45 high to enable V4 and V5, or drive ON45 low
for shutdown. V4 is intended to connect to VCC_PLL.
V5 (VCC_SRAM)
V5 is a linear regulator that provides a fixed 1.1V output
and supplies loads up to 35mA. The power input for the
V4 and V5 linear regulators is IN45, which is typically
connected to V2. To enable V5 on the MAX1587, drive
ON5 high, or drive ON5 low for shutdown. On the
MAX1586, the enable pins for V4 and V5 are combined.
Drive ON45 high to enable V4 and V5, or drive ON45 low
for shutdown. V5 is intended to connect to VCC_SRAM.
V6 (VCC_USIM—MAX1586 Only)
V6 is a linear regulator on the MAX1586 that supplies
loads up to 35mA. The V6 output voltage is pro-
grammed with the I
2
C serial interface to 0V, 1.8V, 2.5V,
or 3.0V. The power-up default for V6 is 0V. See the
Serial Interface
section for details on changing the volt-
age. The power input for the V6 linear regulator is IN6,
which is typically connected to V1. To enable V6, drive
ON6 high, or drive ON6 low for shutdown. V6 is intend-
ed to connect to VCC_USIM.
V7 Always-On Output (VCC_BATT)
The V7 output is always active if V1 is enabled and in
regulation or if backup power is present. When ON1 is
high and V1 is in regulation, V7 is sourced from V1 by
an internal MOSFET switch. When ON1 is low or V1 is
Table 1. Quiescent Operating Current in Various States
OPERATING
POWER MODE
DESCRIPTION
TYPICAL MAX1586/MAX1587
NO-LOAD OPERATING CURRENT
RUN
IDLE
SENSE
STANDBY
All supplies on and running
All supplies on and running, peripherals on
All supplies on, minimal loading, peripherals monitored
All supplies on, minimal loading, peripherals not monitored
200μA MAX1587,
225μA MAX1586
SLEEP
P W R_E N contr ol ed vol ag es ( V 3, V 4, V 5) ar e off. V 1 and V 2 on.
60μA if V1 and V2 SLEEP LDOs on;
130μA if V1, V2 step-down DC-DCs enabled
DEEP SLEEP
All supplies off except V7. V7 biased from backup battery.
5μA MAX1587 if IN > DBI threshold;
32μA MAX1586 if IN > DBI threshold;
4μA if IN < DBI threshold
相關PDF資料 |
PDF描述 |
|---|---|
| MAX1587 | High-Efficiency, Low-IQ PMICs with Dynamic Core for PDAs and Smart Phones |
| MAX1587AETL | High-Efficiency, Low-IQ PMICs with Dynamic Core for PDAs and Smart Phones |
| MAX1586BETM | High-Efficiency, Low-IQ PMICs with Dynamic Core for PDAs and Smart Phones |
| MAX1589A | Low-Input-Voltage, 500mA LDO Regulator with RESET in SOT and TDFN |
| MAX1589AETT | Low-Input-Voltage, 500mA LDO Regulator with RESET in SOT and TDFN |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX1586AETM | 功能描述:直流/直流開關調節器 PMICs w/Dynamic Core for PDAs RoHS:否 制造商:International Rectifier 最大輸入電壓:21 V 開關頻率:1.5 MHz 輸出電壓:0.5 V to 0.86 V 輸出電流:4 A 輸出端數量: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:PQFN 4 x 5 |
| MAX1586AETM+ | 功能描述:直流/直流開關調節器 PMICs w/Dynamic Core for PDAs RoHS:否 制造商:International Rectifier 最大輸入電壓:21 V 開關頻率:1.5 MHz 輸出電壓:0.5 V to 0.86 V 輸出電流:4 A 輸出端數量: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:PQFN 4 x 5 |
| MAX1586AETM+T | 功能描述:直流/直流開關調節器 PMICs w/Dynamic Core for PDAs RoHS:否 制造商:International Rectifier 最大輸入電壓:21 V 開關頻率:1.5 MHz 輸出電壓:0.5 V to 0.86 V 輸出電流:4 A 輸出端數量: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:PQFN 4 x 5 |
| MAX1586AETM-T | 功能描述:直流/直流開關調節器 PMICs w/Dynamic Core for PDAs RoHS:否 制造商:International Rectifier 最大輸入電壓:21 V 開關頻率:1.5 MHz 輸出電壓:0.5 V to 0.86 V 輸出電流:4 A 輸出端數量: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:PQFN 4 x 5 |
| MAX1586AEVCMAXQU | 功能描述:電源管理IC開發工具 MAX1586A Evaluation Kit/Evaluation System RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V |
發布緊急采購，3分鐘左右您將得到回復。