- 您現在的位置：買賣IC網 > PDF目錄383326 > MAX1579ETG (MAXIM INTEGRATED PRODUCTS INC) Complete Bias and White LED Power Supplies for Small TFT Displays PDF資料下載
參數資料
| 型號： | MAX1579ETG |
| 廠商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分類： | 顯示驅動器 |
| 英文描述： | Complete Bias and White LED Power Supplies for Small TFT Displays |
| 中文描述： | LED DISPLAY DRIVER, QCC24 |
| 封裝： | 4 X 4 MM, 0.80 MM HEIGHT, MO-220WGGD-2, TQFN-24 |
| 文件頁數： | 10/13頁 |
| 文件大小： | 221K |
| 代理商： | MAX1579ETG |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁當前第10頁第11頁第12頁第13頁
M
Complete Bias and White LED Power S upplies
for S mall T FT Displays
10
______________________________________________________________________________________
S oft-S tart
The LED boost converter utilizes a soft-start function to
eliminate inrush current during startup. Once the boost
converter is enabled, LX begins switching at the mini-
mum duty cycle until C
COMP
is charged to 1.25V. Once
this occurs, the duty cycle increases to further charge
the output until V
CS
reaches 20% of V
CTRL
. The soft-
start time is adjustable using the capacitor from COMP
to GND. Calculate the required COMP capacitor as:
where t
SS
is the desired soft-start time in seconds.
Overvoltage Protec tion
The output of the LED boost converter is protected from
overvoltage conditions by internal overvoltage circuitry.
If V
OUT
exceeds 34V, the LX switching terminates.
Once V
OUT
falls below 32V, LX switches normally and
soft-start is re-initiated.
Ambient T emperature Derating Func tion
(MAX 1579)
The MAX1579 limits the maximum LED current depend-
ing on the die temperature. V
CS
is limited to 340mV up
to +42
°
C. Once the temperature reaches +42
°
C, the
maximum V
CS
declines by 6mV/
°
C until the minimum
40mV threshold is reached at +100
°
C. Due to the pack-
age’s exposed paddle, the die temperature is always
very close to the PC board temperature.
The temperature derating function allows the LED cur-
rent to be safely set higher at normal operating temper-
atures, thereby allowing either a brighter display or
fewer LEDs to be used for normal display brightness.
S hutdown
The MAX1578/MAX1579 include a low-quiescent-current
shutdown mode. To enter shutdown, drive CTRL below
0.1V for longer than 10.5ms and drive ONBIAS low. The
quiescent current is reduced to less than 1μA when the
boost converter and charge pumps are disabled.
To disable the LED boost converter, drive CTRL below
0.1V for longer than 10.5ms. During shutdown, the
internal boost switch from LX to PGND is high imped-
ance; however, a DC path exists from IN to OUT
through the external inductor and Schottky diode. Drive
CTRL with an analog voltage between 0.24V and 1.65V
or a 200Hz to 200kHz digital PWM dimming signal for
normal operation. The quiescent current is reduced to
870μA when the boost converter is shut down and the
charge pumps are enabled.
Drive ONBIAS low to shut down the internal POS and
NEG charge pumps and disable the MAIN LDO output.
On-chip pulldown resistors discharge these outputs
during shutdown. Drive ONBIAS high for normal opera-
tion. V
DD
is connected to IN when ONBIAS is low. The
quiescent current is reduced to 430μA when the charge
pumps are shut down and the boost converter is
enabled.
Applic ations Information
Adjusting LED Current
Set the maximum LED current using a resistor from CS
to GND. Calculate the resistance as follows:
where I
LED
is the desired maximum current through the
LEDs in Amps when V
CTRL
is 1.65V.
LED Dimming Control Using a DAC
V
CTRL
controls the LED drive current. The voltage at CS
regulates to 20% of V
CTRL
to control the current
through the LEDs and, therefore, the brightness. Drive
CTRL using a DAC with an output voltage between
0.24V and 1.65V to control the brightness of the LEDs.
Increasing V
CTRL
beyond 1.65V results in no further
brightness increase. Hold CTRL below 100mV for
longer than 10.5ms to shut down the boost converter.
LED Dimming Using Direc t PWM into CT RL
Another useful technique for LED dimming control is the
application of a logic-level PWM signal applied directly
to CTRL. LED current may be varied from zero to full
scale. The frequency range of the PWM signal is from
200Hz to 200kHz, while 0% duty cycle corresponds to
zero current and 100% duty cycle corresponds to full
current. The error amplifier and compensation capaci-
tor form a lowpass filter so PWM dimming results in DC
current to the LEDs without the need for any additional
RC filters. See the
Typical Operating Characteristics
.
Input/Output Ripple
For LED drivers, input and output ripple may be impor-
tant. Input ripple depends on the source supply’s output
impedance. Adding a lowpass filter to the input further
reduces input ripple. Alternately, increasing C
IN
to 10μF
cuts input ripple in half. Likewise, an output filter or high-
er output capacitance value reduces output ripple.
R
mV
I
for the MAX
R
mV
I
for the MAX
CS
LED
340
CS
LED
=
=
330
1578
1579
C
A
.
t
V
COMP
SS
=
×
12
1 25
μ
相關PDF資料 |
PDF描述 |
|---|---|
| MAX1584 | 5-Channel Slim DSC Power Supplies |
| MAX1585 | 5-Channel Slim DSC Power Supplies |
| MAX1584-MAX1585 | 5-Channel Slim DSC Power Supplies |
| MAX1584ETJ | 5-Channel Slim DSC Power Supplies |
| MAX1585ETJ | 5-Channel Slim DSC Power Supplies |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX1579ETG+ | 功能描述:LED照明驅動器 Cmplete Bias & White LED Power Supply RoHS:否 制造商:STMicroelectronics 輸入電壓:11.5 V to 23 V 工作頻率: 最大電源電流:1.7 mA 輸出電流: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:SO-16N |
| MAX1579ETG+T | 功能描述:LED照明驅動器 Cmplete Bias & White LED Power Supply RoHS:否 制造商:STMicroelectronics 輸入電壓:11.5 V to 23 V 工作頻率: 最大電源電流:1.7 mA 輸出電流: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:SO-16N |
| MAX1579ETG-T | 功能描述:LED照明驅動器 RoHS:否 制造商:STMicroelectronics 輸入電壓:11.5 V to 23 V 工作頻率: 最大電源電流:1.7 mA 輸出電流: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:SO-16N |
| MAX1579EVKIT | 功能描述:LED 照明開發工具 Evaluation Kit for the MAX1579 RoHS:否 制造商:Fairchild Semiconductor 產品:Evaluation Kits 用于:FL7732 核心: 電源電壓:120V 系列: 封裝: |
| MAX157ACPA | 功能描述:模數轉換器 - ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
發布緊急采購，3分鐘左右您將得到回復。