- 您現在的位置：買賣IC網 > PDF目錄383326 > MAX1576 (Maxim Integrated Products, Inc.) 480mA White LED 1x/1.5x/2x Charge Pump for Backlighting and Camera Flash PDF資料下載
參數資料
| 型號： | MAX1576 |
| 廠商： | Maxim Integrated Products, Inc. |
| 英文描述： | 480mA White LED 1x/1.5x/2x Charge Pump for Backlighting and Camera Flash |
| 中文描述： | 480mA白光LED 1倍/1.5倍/2倍電荷泵，用于背光和相機閃光燈 |
| 文件頁數： | 20/22頁 |
| 文件大小： | 2258K |
| 代理商： | MAX1576 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁當前第20頁第21頁第22頁
MC14489B
20
MOTOROLA
THERMAL CONSIDERATIONS
The MC14489B is designed to operate with a chip–junction
temperature (TJ) ranging from – 40 to 130
°
C, as indicated in
the electrical characteristics tables. The ambientoperating
temperature range (TA) is dependent on R
θ
JA, the internal
chip current, how many anode drivers are used, the number
of bank drivers used, the drive current, and how the package
is cooled. The maximum ratings table gives the thermal resis-
tance, junction–to–ambient, of the MC14489B mounted on a
pc board using natural convection to be 90
°
C per watt for the
plastic DIP. The SOG thermal resistance is 100
°
C per watt.
The following general equation (1) is used to determine the
power dissipated by the MC14489B.
PT = PD + PI
(1)
where
PT= Total power dissipation of the MC14489B
PD= Power dissipated in the driver circuitry (mW)
PI= Power dissipated by the internal chip
circuitry (mW)
The equations for the two terms of the general equation
are:
PD = (iOH) (N)(VDD – VLED)(B/5)
(2)
(3)
PI = (1.5 mA)(VDD) + IRx(VDD – IRxRx)
where
iOH= Peak anode driver current (mA)
IRx= iOH /10, with iOH = the peak anode driver current
(mA) when the dimmer bit is high
N = Number of anode drivers used
B = Number of bank drivers used
Rx = External resistor value (k
)
VDD= Maximum supply voltage, referenced to VSS
(volts)
VLED= Minimum anticipated voltage drop across the
LED
1.5 mA = Operating supply current of the MC14489B
The following two examples show how to calculate the
maximum allowable ambient temperature.
Worst–Case Analysis Example 1:
5–digit display with decimals (5 banks and 8 anode drivers)
DIP without heat sink on PC board
iOH= 20 mA max
VLED= 1.8 V min
VDD= 5.25 max
PD = (20)(8)(5.25 – 1.8)(5/5) = 552 mW
Ref. (2)
PI = (1.5)(5.25) + 2[5.25 – 2(2)] = 10 mW
Ref. (3)
Therefore, PT = 552 + 10 = 562 mW
Ref. (1)
and
Tchip = R
θ
JAPT = (90
°
C/W)(0.562) = 51
°
C
Finally, the maximum allowable
TA = TJmax –
Tchip = 130 – 51 = 79
°
C
That is, if TA = 79
°
C, the maximum junction temperature is
130
°
C. The chip’s average temperature for this example is
lower than 130
°
C because all segments are usually not illumi-
nated simultaneously for an indefinite period.
Worst–Case Analysis Example 2:
16 lamps (4 banks and 4 anode drivers)
SOG without heat sink on PC board
iOH= 30 mA max
VLED= 1.8 V min
VDD= 5.5 max
PD = (30)(4)(5.5 – 1.8)(4/5) = 355 mW
PI = (1.5)(5.5) + 3[5.5 – 3(1.0)] = 16 mW
Therefore, PT = 355 + 16 = 371 mW
and
Tchip = R
θ
JAPT = (100
°
C/W)(0.371) = 37
°
C
Finally, the maximum allowable
TA = TJmax –
Tchip = 130 – 37 = 93
°
C
To extend the allowable ambient temperature range or to
reduce TJ, which extends chip life, a heat sink such as shown
in Figure 20 can be used in high–current applications. Alter-
natively, heat–spreader techniques can be used on the PC
board, such as running a wide trace under the MC14489B and
using thermal paste. Wide, radial traces from the MC14489B
leads also act as heat spreaders.
Ref. (2)
Ref. (3)
Ref. (1)
AAVID #5804 or equivalent
(Tel. 603/524–4443, FAX 603/528–1478)
Motorola cannot recommend one supplier over another and
in no way suggests that this is the only heat sink supplier.
Figure 20. Heat Sink
Table 3. LED Lamp and Common–Cathode Display
Manufacturers
Supplier
QT Optoelectronics
Hewlett–Packard (HP), Components Group
Industrial Electronic Engineers (IEE), Component Products Div.
Purdy Electronics Corp., AND Product Line
NOTE: Motorola cannot recommend one supplier over another
and in no way suggests that this is a complete listing of
LED suppliers.
相關PDF資料 |
PDF描述 |
|---|---|
| MAX1576ETG | 480mA White LED 1x/1.5x/2x Charge Pump for Backlighting and Camera Flash |
| MAX1577ZETA | 1.2A White LED Regulating Charge Pump for Camera Flashes and Movie Lights |
| MAX1577Y | CAP 10UF 50V ELECT TG SMD |
| MAX1577YETA | 1.2A White LED Regulating Charge Pump for Camera Flashes and Movie Lights |
| MAX1579 | Complete Bias and White LED Power Supplies for Small TFT Displays |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX1576ETG | 功能描述:LED照明驅動器 RoHS:否 制造商:STMicroelectronics 輸入電壓:11.5 V to 23 V 工作頻率: 最大電源電流:1.7 mA 輸出電流: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:SO-16N |
| MAX1576ETG+ | 功能描述:LED照明驅動器 White LED 1/1.5/2x Charge Pump RoHS:否 制造商:STMicroelectronics 輸入電壓:11.5 V to 23 V 工作頻率: 最大電源電流:1.7 mA 輸出電流: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:SO-16N |
| MAX1576ETG+T | 功能描述:LED照明驅動器 White LED 1/1.5/2x Charge Pump RoHS:否 制造商:STMicroelectronics 輸入電壓:11.5 V to 23 V 工作頻率: 最大電源電流:1.7 mA 輸出電流: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:SO-16N |
| MAX1576ETG-T | 功能描述:LED照明驅動器 RoHS:否 制造商:STMicroelectronics 輸入電壓:11.5 V to 23 V 工作頻率: 最大電源電流:1.7 mA 輸出電流: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:SO-16N |
| MAX1576EVKIT | 功能描述:LED 照明開發工具 Evaluation Kit for the MAX1576 RoHS:否 制造商:Fairchild Semiconductor 產品:Evaluation Kits 用于:FL7732 核心: 電源電壓:120V 系列: 封裝: |
發布緊急采購，3分鐘左右您將得到回復。