- 您現在的位置：買賣IC網 > PDF目錄383326 > MAX1572ETC075 (MAXIM INTEGRATED PRODUCTS INC) 800mA, 2MHz, PWM DC-to-DC Step-Down Converter with RESET PDF資料下載
參數資料
| 型號： | MAX1572ETC075 |
| 廠商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分類： | 穩壓器 |
| 英文描述： | 800mA, 2MHz, PWM DC-to-DC Step-Down Converter with RESET |
| 中文描述： | 2.1 A SWITCHING REGULATOR, 2200 kHz SWITCHING FREQ-MAX, QCC12 |
| 封裝： | 4 X 4 MM, 0.80 MM HEIGHT, MO-220WGGB, TQFN-12 |
| 文件頁數： | 9/11頁 |
| 文件大小： | 340K |
| 代理商： | MAX1572ETC075 |
M
800mA, 2MHz, PWM DC-to-DC
Step-Down Converter with
RESET
_______________________________________________________________________________________
9
Soft-Start
Soft-start is used to prevent input-current overshoot dur-
ing startup. For most applications using a 10μF output
capacitor, connect a 1000pF capacitor from SS to GND.
If a larger output capacitor is used, then use the follow-
ing formula to find the value of the soft-start capacitor
needed to prevent input-current overshoot:
C
SS
= C
OUT
/10
4
During soft-start, the output voltage rises from 0 to
V
OUT(nom)
with a time constant equal to C
SS
times
100k
(see the
Typical Operating Characteristics
).
170ms
RESET
RESET
is an open-drain output with an internal 14k
pullup resistor to OUT. During startup,
RESET
is held low
until 200ms (typ) after the output voltage reaches 90% of
its nominal regulation voltage. When the output voltage
drops below 90% of its nominal regulation voltage,
RESET
pulls low again. See the
Typical Operating
Characteristics
section for
RESET
waveforms during
startup and shutdown.
Applications Information
Inductor Selection
A 2.2μH inductor with a saturation current of at least 1A
is recommended for full-load (800mA) applications. For
lower load currents, the inductor current rating may be
reduced. For most applications, use an inductor with a
current rating 1.25 times the maximum required output
current. For maximum efficiency, the inductor
’
s DC
resistance should be as low as possible. See Table 2
for recommended inductors and manufacturers.
Capacitor Selection
Ceramic 10μF input and output capacitors are recom-
mended for most applications. For output voltages
below 1.5V, output capacitance should be increased to
22μF. For best stability over a wide temperature range,
use capacitors with an X5R or better dielectric.
ABATT Input Filter
In normal applications, an RC filter on ABATT keeps
power-supply noise from entering the IC. Connect a
10
resistor between BATT and ABATT and connect a
0.1μF capacitor from ABATT to GND.
PC Board Layout and Routing
Due to fast-switching waveforms and high-current
paths, careful PC board layout is required. An evalua-
tion kit (MAX1572EVKIT) is available to speed design.
When laying out a board, minimize trace lengths
between the IC, the inductor, the input capacitor, and the
output capacitor. Keep these traces short, direct, and
wide. Keep noisy traces, such as the LX node trace,
away from OUT. The input bypass capacitors should be
placed as close to the IC as possible. Connect PGND
and GND directly to the exposed paddle underneath the
IC. The ground connections of the input and output
capacitors should be as close together as possible.
I
OUT
V
OUT
(CONVENTIONAL)
V
OUT
(VOLTAGE POSITIONING)
Figure 2. Load Transient Response, With and Without Voltage
Positioning
CHANGE IN
OUTPUT
VOLTAGE (%)
NORMAL OPERATION
FORCED-PWM
V
IN
= 5.5V
V
IN
= 2.6V
+1
0
-1
-2
0
200
400
600
800
LOAD CURRENT (mA)
V
IN
= 3.6V
Figure 3. Voltage-Positioning Load Line
相關PDF資料 |
PDF描述 |
|---|---|
| MAX1572ETC130 | 800mA, 2MHz, PWM DC-to-DC Step-Down Converter with RESET |
| MAX1572ETC150 | 800mA, 2MHz, PWM DC-to-DC Step-Down Converter with RESET |
| MAX1572ETC180 | 800mA, 2MHz, PWM DC-to-DC Step-Down Converter with RESET |
| MAX1572ETC250 | 800mA, 2MHz, PWM DC-to-DC Step-Down Converter with RESET |
| MAX1574ETB | 180mA, 1x/2x, White LED Charge Pump in 3mm x 3mm TDFN |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX1572ETC075+ | 制造商:Rochester Electronics LLC 功能描述: 制造商:Maxim Integrated Products 功能描述: |
| MAX1572ETC130 | 功能描述:直流/直流開關轉換器 RoHS:否 制造商:STMicroelectronics 最大輸入電壓:4.5 V 開關頻率:1.5 MHz 輸出電壓:4.6 V 輸出電流:250 mA 輸出端數量:2 最大工作溫度:+ 85 C 安裝風格:SMD/SMT |
| MAX1572ETC130+ | 功能描述:直流/直流開關轉換器 800mA 2MHz PWM Step-Down w/Reset RoHS:否 制造商:STMicroelectronics 最大輸入電壓:4.5 V 開關頻率:1.5 MHz 輸出電壓:4.6 V 輸出電流:250 mA 輸出端數量:2 最大工作溫度:+ 85 C 安裝風格:SMD/SMT |
| MAX1572ETC130+T | 功能描述:直流/直流開關轉換器 800mA 2MHz PWM Step-Down w/Reset RoHS:否 制造商:STMicroelectronics 最大輸入電壓:4.5 V 開關頻率:1.5 MHz 輸出電壓:4.6 V 輸出電流:250 mA 輸出端數量:2 最大工作溫度:+ 85 C 安裝風格:SMD/SMT |
| MAX1572ETC130-T | 功能描述:直流/直流開關轉換器 RoHS:否 制造商:STMicroelectronics 最大輸入電壓:4.5 V 開關頻率:1.5 MHz 輸出電壓:4.6 V 輸出電流:250 mA 輸出端數量:2 最大工作溫度:+ 85 C 安裝風格:SMD/SMT |
發布緊急采購，3分鐘左右您將得到回復。