參數資料
型號： MAX1566-MAX1567
廠商： Maxim Integrated Products, Inc.
英文描述： Six-Channel, High-Efficiency, Digital Camera Power Supplies
中文描述： 六通道，高效率，數碼相機電源
文件頁數： 30/35頁
文件大?。?/td> 1134K
代理商： MAX1566-MAX1567
M
Six-Channel, High-Efficiency, Digital
Camera Power Supplies
30
______________________________________________________________________________________
For the example:
C
OUT
= 27k
x 6.8nF / 5.14
= 35.7μF
Since ceramic capacitors are common in either 22μF or
47μF values, 22μF is within a factor of two of the ideal value
and still provides adequate phase margin for stability. If
the output filter capacitor has significant ESR, a zero
occurs at the following:
Z
ESR
= 1 / (2
π
x C
OUT
x R
ESR
)
If Z
ESR
> f
C
, it can be ignored, as is typically the case
with ceramic output capacitors. If Z
ESR
< f
C
, it should
be cancelled with a pole set by capacitor C
P
connect-
ed from C
C
to GND:
C
P
= C
OUT
x R
ESR
/ R
C
If C
P
is calculated to be <10pF, it can be omitted.
AUX Controller Component Selection
External MOSFET
All MAX1566/MAX1567 AUX controllers drive external
logic-level MOSFETs. Significant MOSFET selection
parameters are as follows:
On-resistance (R
DS(ON)
)
Maximum drain-to-source voltage (V
DS(MAX)
)
Total gate charge (Q
G
)
Reverse transfer capacitance (C
RSS
)
On the MAX1566, all AUX drivers are designed for N-
channel MOSFETs. On the MAX1567, AUX2 is a DC-to-
DC inverter, so DL2 is designed to drive a P-channel
MOSFET. In both devices, the driver outputs DL1 and
DL3 swing between PVSU and GND. MOSFET driver
DL2 swings between INDL2 and GND.
Use a MOSFET with on-resistance specified with gate
drive at or below the main output voltage. The gate
charge, Q
G
, includes all capacitance associated with
charging the gate and helps to predict MOSFET transi-
tion time between on and off states. MOSFET power
dissipation is a combination of on-resistance and tran-
sition losses. The on-resistance loss is as follows:
P
RDSON
= D x I
L
2
x R
DS(ON)
where D is the duty cycle, I
L
is the average inductor
current, and R
DS(ON)
is MOSFET on-resistance. The
transition loss is approximately as follows:
P
TRANS
= (V
OUT
x I
L
x f
OSC
x t
T
) / 3
where V
OUT
is the output voltage, I
L
is the average
inductor current, f
OSC
is the switching frequency, and
t
T
is the transition time. The transition time is approxi-
mately Q
G
/ I
G
, where Q
G
is the total gate charge, and
I
G
is the gate-drive current (0.5A typ).
The total power dissipation in the MOSFET is as follows:
P
MOSFET
= P
RDSON
+ P
TRANS
Diode
For most AUX applications, a Schottky diode rectifies
the output voltage. Schottky low forward voltage and
fast recovery time provide the best performance in
most applications. Silicon signal diodes (such as
1N4148) are sometimes adequate in low-current
(<10mA), high-voltage (>10V) output circuits where the
output voltage is large compared to the diode forward
voltage.
AUX Compensation
The auxiliary controllers employ voltage-mode control
to regulate their output voltage. Optimum compensa-
tion depends on whether the design uses continuous or
discontinuous inductor current.
AUX Step-Up, Discontinuous Inductor Current
When the inductor current falls to zero on each switch-
ing cycle, it is described as discontinuous
.
The inductor
is not utilized as efficiently as with continuous current,
but in light-load applications this often has little negative
impact since the coil losses may already be low com-
pared to other losses. A benefit of discontinuous induc-
tor current is more flexible loop compensation, and no
maximum duty-cycle restriction on boost ratio.
To ensure discontinuous operation, the inductor must
have a sufficiently low inductance to fully discharge on
each cycle. This occurs when:
L < [V
IN
2
(V
OUT
- V
IN
) / V
OUT
3
] [R
LOAD
/ (2f
OSC
)]
A discontinuous current boost has a single pole at the
following:
f
P
= (2V
OUT
- V
IN
) / (2
π
x R
LOAD
x C
OUT
x V
OUT
)
Choose the integrator cap so the unity-gain crossover,
f
C
, occurs at f
OSC
/ 10 or lower. Note that for many AUX
circuits, such as those powering motors, LEDs, or other
loads that do not require fast transient response, it is
often acceptable to overcompensate by setting f
C
at
f
OSC
/ 20 or lower.
C
C
is then determined by the following:
C
C
= [2V
OUT
x V
IN
/ ((2V
OUT
- V
IN
) x V
RAMP
)] [V
OUT
/
(K(V
OUT
- V
IN
))]
1/2
[(V
FB
/ V
OUT
)(g
M
/ (2
π
x f
C
))]
where:
K = 2L x f
OSC
/ R
LOAD
and V
RAMP
is the internal slope-compensation voltage
ramp of 1.25V.
相關PDF資料
PDF描述
MAX156ACNG 8-/4-Channel ADCs with Simultaneous T/Hs and Reference
MAX156BCNG 8-/4-Channel ADCs with Simultaneous T/Hs and Reference
MAX156BENG 8-/4-Channel ADCs with Simultaneous T/Hs and Reference
MAX155AEPI 8-/4-Channel ADCs with Simultaneous T/Hs and Reference
MAX155BEPI CONN HEADER 2POS R/A W/CLIP SMD
相關代理商/技術參數
參數描述
MAX1567ETL 功能描述:PMIC 解決方案 RoHS:否 制造商:Texas Instruments 安裝風格:SMD/SMT 封裝 / 箱體:QFN-24 封裝:Reel
MAX1567ETL+ 功能描述:PMIC 解決方案 6Ch Digital Camera Power Supply RoHS:否 制造商:Texas Instruments 安裝風格:SMD/SMT 封裝 / 箱體:QFN-24 封裝:Reel
MAX1567ETL+T 功能描述:PMIC 解決方案 6Ch Digital Camera Power Supply RoHS:否 制造商:Texas Instruments 安裝風格:SMD/SMT 封裝 / 箱體:QFN-24 封裝:Reel
MAX1567ETL-T 功能描述:PMIC 解決方案 RoHS:否 制造商:Texas Instruments 安裝風格:SMD/SMT 封裝 / 箱體:QFN-24 封裝:Reel
MAX1567EVKIT 制造商:Maxim Integrated Products 功能描述:6-CHANNEL HIGH EFFICIENCY DIGITAL CAMERA POWE - Bulk
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*