參數資料
型號： MAX1515
廠商： Maxim Integrated Products, Inc.
英文描述： Low-Voltage, Internal Switch, Step-Down/DDR Regulator
中文描述： 低電壓、內置開關、降壓型/DDR穩壓器
文件頁數： 21/24頁
文件大?。?/td> 504K
代理商： MAX1515
M
Low-Voltage, Internal Switch,
Step-Down/DDR Regulator
______________________________________________________________________________________
21
voltage-divider network at REFIN. The resulting output
voltages are determined by the following equations:
Forced-PWM operation is required to ensure fast, accu-
rate negative voltage transitions when REFIN is low-
ered. Since forced-PWM operation disables the
zero-crossing comparator, the inductor current can
reverse under light loads, quickly discharging the out-
put capacitors.
For a step voltage change at REFIN, the rate-of-change
of the output voltage is limited by the inductor current
ramp, the total output capacitance, the current limit,
and the load during the transition. The inductor current
ramp is limited by the voltage across the inductor and
the inductance. The total output capacitance deter-
mines how much current is needed to change the out-
put voltage. Additional load current slows down the
output-voltage change during a positive REFIN voltage
change, and speeds up the output-voltage change dur-
ing a negative REFIN voltage change. Increasing the
current-limit setting speeds up a positive output-voltage
change.
To avoid tripping the power-good comparators, the ref-
erence-voltage slew rate must be slow enough that the
output voltage (V
OUT
) can accurately track the refer-
ence voltage (V
REFIN
). Add a capacitor across REFIN
and GND to control the rate-of-change of the REFIN
voltage during dynamic transitions and filter noise.
With the additional capacitance, the REFIN voltage
slews between the two set points with a time constant
given by R
EQ
x C
REFIN
, where R
EQ
is the equivalent
parallel resistance seen by the slew capacitor.
Referring to Figure 7, the time constant for a positive
REFIN voltage transition is:
and the time constant for a negative REFIN voltage
transition is:
PC Board Layout Guidelines
Good layout is necessary to achieve the intended out-
put power level, high efficiency, and low noise. Good
layout includes the use of a ground plane, careful com-
ponent placement, and correct routing of traces using
appropriate trace widths. Refer to the MAX1515 EV kit
for a reference of a good layout.
The following points are in order of decreasing impor-
tance:
1) Minimize switched-current and high-current ground
loops. Connect the input capacitor’s ground, the
output capacitor’s ground, and PGND at a single
point. Connect the resulting island to GND at only
one point.
2) Connect the input filter capacitor less than 5mm
away from IN. The connecting copper trace carries
large currents and must be at least 1mm wide,
preferably 2.5mm.
3) Place the LX node components as close together
and as near to the device as possible. This reduces
noise, resistive losses, and switching losses.
4) A ground plane is essential for optimal perfor-
mance. In most applications, the circuit is located
on a multilayer board, and full use of the four or
more layers is recommended. Use the top and bot-
tom layers for interconnections and the inner layers
for an uninterrupted ground plane. Avoid large AC
currents through the ground plane.
Chip Information
TRANSISTOR COUNT: 8258
PROCESS: BiCMOS
τ
POS
REFIN
C
R
R
R
R
=
×
+
1
1
2
2
τ
POS
REFIN
C
R
R
R
R
R
R
=
×
+
+
+
1
2
2
3
3
1
(
)
V
V
R
+
R
R
V
V
R
+
R
+
R
R
R
OUT LOW
(
REF
OUT HIGH
(
REF
)
)
=
=
+
2
2
1
2
2
3
1
3
MAX1515
LX
GND
FB
PGND
V
OUT
FBSEL1
SKIP
FBSEL0
MODE
REFIN
REF
R3
R2
R1
V
OUT(LOW)
V
OUT(HIGH)
C
OUT
V
CC
L
C
REFIN
Figure 7. Dynamic Output Voltages
相關PDF資料
PDF描述
MAX1515ETG Low-Voltage, Internal Switch, Step-Down/DDR Regulator
MAX1516 TFT-LCD DC-DC Converters with Operational Amplifiers
MAX1516ETJ TFT-LCD DC-DC Converters with Operational Amplifiers
MAX1517 TFT-LCD DC-DC Converters with Operational Amplifiers
MAX1517ETJ TFT-LCD DC-DC Converters with Operational Amplifiers
相關代理商/技術參數
參數描述
MAX1515ETG 功能描述:直流/直流開關調節器 RoHS:否 制造商:International Rectifier 最大輸入電壓:21 V 開關頻率:1.5 MHz 輸出電壓:0.5 V to 0.86 V 輸出電流:4 A 輸出端數量: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:PQFN 4 x 5
MAX1515ETG+ 功能描述:直流/直流開關調節器 3A 1MHz Step-Down DDR Regulator RoHS:否 制造商:International Rectifier 最大輸入電壓:21 V 開關頻率:1.5 MHz 輸出電壓:0.5 V to 0.86 V 輸出電流:4 A 輸出端數量: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:PQFN 4 x 5
MAX1515ETG+T 功能描述:直流/直流開關調節器 3A 1MHz Step-Down DDR Regulator RoHS:否 制造商:International Rectifier 最大輸入電壓:21 V 開關頻率:1.5 MHz 輸出電壓:0.5 V to 0.86 V 輸出電流:4 A 輸出端數量: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:PQFN 4 x 5
MAX1515ETG-T 功能描述:直流/直流開關調節器 RoHS:否 制造商:International Rectifier 最大輸入電壓:21 V 開關頻率:1.5 MHz 輸出電壓:0.5 V to 0.86 V 輸出電流:4 A 輸出端數量: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:PQFN 4 x 5
MAX1515EVKIT 制造商:Maxim Integrated Products 功能描述:3A 1MHZ LOW-VOLTAGE INTERNAL SWI - Rail/Tube
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*