參數資料
型號: MAX15005
廠商: Maxim Integrated Products, Inc.
英文描述: 4.5V to 40V Input Automotive Flyback/Boost/SEPIC Power-Supply Controllers
中文描述: 4.5V至40V輸入、用于汽車電子的反激/boost/SEPIC電源控制器
文件頁數: 12/29頁
文件大小: 547K
代理商: MAX15005
M
4.5V to 40V Input Automotive
Flyback/Boost/SEPIC Power-Supply Controllers
12
______________________________________________________________________________________
operation of the power supply; however, to reduce the
power dissipation of the internal LDO, it can be dis-
abled by applying an external voltage higher than 7.4V
at V
CC
(LDO output). The LDO then stops drawing cur-
rent from IN, thereby reducing the power dissipation in
the IC. The V
CC
voltage is clamped to 10.4V with 30mA
current sink in case there is a higher voltage at the bias
winding. This feature is useful in applications with con-
tinuous higher input voltage.
The second 5V LDO regulator from V
CC
to REG5 pro-
vides power to the internal control circuits. This LDO can
also be used to source 15mA of external load current.
Bypass V
CC
and REG5 with a parallel combination of
1μF and 0.1μF low-ESR ceramic capacitors. Additional
capacitors (up to 22μF) at V
CC
can be used although
they are not necessary for proper operation of the
MAX15004/MAX15005.
Startup Operation/UVLO/ON/
OFF
The MAX15004A/B/MAX15005A/B feature two under-
voltage lockouts (UVLO). The internal UVLO monitors
the V
CC
-regulator and turns on the converter once V
CC
rises above 3.5V. The internal UVLO circuit has about
0.5V hysteresis to avoid chattering during turn-on. Once
the power is on and the bootstrapped voltage feeds
V
CC
, IN voltage can drop below 4V. This feature pro-
vides operation at a cold-crank voltage as low as 2.5V.
An external undervoltage lockout can be achieved by
controlling the voltage at the ON/
OFF
input. The
ON/
OFF
input threshold is set at 1.23V (rising) with
75mV hysteresis.
Before any operation can commence, the ON/
OFF
volt-
age must exceed the 1.23V threshold.
Calculate R1 in Figure 1 by using the following formula:
where V
UVLO
is the ON/
OFF
’s 1.23V rising threshold,
and V
ON
is the desired input startup voltage. Choose
an R2 value in the 100k
range. The UVLO circuits
keep the PWM comparator, ILIM comparator, oscillator,
and output driver shut down to reduce current con-
sumption (see the Functional Diagram). The ON/
OFF
input can be used to disable the MAX15004/MAX15005
and reduce the standby current to less than 20μA.
Soft-Start
The MAX15004/MAX15005 are provided with an exter-
nally adjustable soft-start function, saving a number of
external components. The SS is a 1.228V reference
bypass connection for the MAX15004A/B/MAX15005A/B
and also controls the soft-start period. At startup, after
V
IN
is applied and the UVLO thresholds are reached,
the device enters soft-start. During soft-start, 15μA is
sourced into the capacitor (C
SS
) connected from SS to
GND causing the reference voltage to ramp up slowly.
The HICCUP mode of operation is disabled during soft-
start. When V
SS
reaches 1.228V, the output as well as
the HICCUP mode become fully active. Set the soft-start
time (t
SS
) using following equation:
where t
SS
is in seconds and C
SS
is in farads.
The soft-start programmability is important to control the
input inrush current issue and also to avoid the
MAX15004/MAX15005 power supply from going into the
unintentional hiccup during the startup. The required
soft-start time depends on the topology used, current-
limit setting, output capacitance, and the load condition.
Oscillator Frequency/
External Synchronization
Use an external resistor and capacitor at RTCT to pro-
gram the MAX15004A/B/MAX15005A/B internal oscillator
frequency from 15kHz to 1MHz. The MAX15004A/B out-
put switching frequency is one-half the programmed
oscillator frequency with a 50% maximum duty-cycle
limit. The MAX15005A/B output switching frequency is
the same as the oscillator frequency. The RC network
connected to RTCT controls both the oscillator frequency
and the maximum duty cycle. The CT capacitor charges
and discharges from (0.1 x V
REG5
) to (0.55 x V
REG5
). It
charges through RT and discharges through an internal
trimmed controlled current sink. The maximum duty
cycle is inversely proportional to the discharge time
t
V
C
( )
A
SS
SS
=
×
1 23
15 10
6
.
( )
R
V
V
R
ON
UVLO
1
1
2
=
×
Figure 1. Setting the MAX15004A/B/MAX15005A/B
Undervoltage Lockout Threshold
MAX15004A/B
MAX15005A/B
ON/OFF
R1
1.23V
R2
V
IN
相關PDF資料
PDF描述
MAX15005AAUE 4.5V to 40V Input Automotive Flyback/Boost/SEPIC Power-Supply Controllers
MAX15005BAUE 4.5V to 40V Input Automotive Flyback/Boost/SEPIC Power-Supply Controllers
MAX15012_07 175V/2A, High-Speed, Half-Bridge MOSFET Drivers
MAX15012AASA 175V/2A, High-Speed, Half-Bridge MOSFET Drivers
MAX15012BASA 175V/2A, High-Speed, Half-Bridge MOSFET Drivers
相關代理商/技術參數
參數描述
MAX15005AAUE/V+ 功能描述:電流型 PWM 控制器 Flyback/Boost/SEPIC Power-Supply Ctlr RoHS:否 制造商:Texas Instruments 開關頻率:27 KHz 上升時間: 下降時間: 工作電源電壓:6 V to 15 V 工作電源電流:1.5 mA 輸出端數量:1 最大工作溫度:+ 105 C 安裝風格:SMD/SMT 封裝 / 箱體:TSSOP-14
MAX15005AAUE/V+T 功能描述:電流型 PWM 控制器 Flyback/Boost/SEPIC Power-Supply Ctlr RoHS:否 制造商:Texas Instruments 開關頻率:27 KHz 上升時間: 下降時間: 工作電源電壓:6 V to 15 V 工作電源電流:1.5 mA 輸出端數量:1 最大工作溫度:+ 105 C 安裝風格:SMD/SMT 封裝 / 箱體:TSSOP-14
MAX15005AAUE+ 功能描述:電流型 PWM 控制器 Flyback/Boost/SEPIC Power-Supply Ctlr RoHS:否 制造商:Texas Instruments 開關頻率:27 KHz 上升時間: 下降時間: 工作電源電壓:6 V to 15 V 工作電源電流:1.5 mA 輸出端數量:1 最大工作溫度:+ 105 C 安裝風格:SMD/SMT 封裝 / 箱體:TSSOP-14
MAX15005AAUE+T 功能描述:電流型 PWM 控制器 Flyback/Boost/SEPIC Power-Supply Ctlr RoHS:否 制造商:Texas Instruments 開關頻率:27 KHz 上升時間: 下降時間: 工作電源電壓:6 V to 15 V 工作電源電流:1.5 mA 輸出端數量:1 最大工作溫度:+ 105 C 安裝風格:SMD/SMT 封裝 / 箱體:TSSOP-14
MAX15005AAUEEVKIT+ 功能描述:電流型 PWM 控制器 4.5V to 40V Input Automotive Flyback/Boost/SEPIC Power-Supply Controllers RoHS:否 制造商:Texas Instruments 開關頻率:27 KHz 上升時間: 下降時間: 工作電源電壓:6 V to 15 V 工作電源電流:1.5 mA 輸出端數量:1 最大工作溫度:+ 105 C 安裝風格:SMD/SMT 封裝 / 箱體:TSSOP-14