- 您現在的位置：買賣IC網 > PDF目錄383321 > MAX149ACPP (MAXIM INTEGRATED PRODUCTS INC) +2.7V to +5.25V, Low-Power, 8-Channel, Serial 10-Bit ADCs PDF資料下載
參數資料
| 型號： | MAX149ACPP |
| 廠商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分類： | ADC |
| 英文描述： | +2.7V to +5.25V, Low-Power, 8-Channel, Serial 10-Bit ADCs |
| 中文描述： | 8-CH 10-BIT SUCCESSIVE APPROXIMATION ADC, SERIAL ACCESS, PDIP20 |
| 封裝： | PLASTIC, DIP-20 |
| 文件頁數： | 14/24頁 |
| 文件大小： | 221K |
| 代理商： | MAX149ACPP |
M
+2.7V to +5.25V, Low-Power, 8-Channel,
S erial 10-Bit ADCs
14
______________________________________________________________________________________
bit of the control byte (the PD0 bit) is clocked into DIN.
The start bit is defined as follows:
The first high bit clocked into DIN with
CS
low any
time the converter is idle; e.g., after V
DD
is applied.
OR
The first high bit clocked into DIN after bit 3 of a con-
version in progress is clocked onto the DOUT pin.
If CS is toggled before the current conversion is com-
plete, the next high bit clocked into DIN is recognized as
a start bit; the current conversion is terminated, and a
new one is started.
The fastest the MAX148/MAX149 can run with
CS
held
low between conversions is 15 clocks per conversion.
Figure 11a shows the serial-interface timing necessary to
perform a conversion every 15 SCLK cycles in external
clock mode. If
CS
is tied low and SCLK is continuous,
guarantee a start bit by first clocking in 16 zeros.
Most microcontrollers (μCs) require that conversions
occur in multiples of 8 SCLK clocks; 16 clocks per con-
version is typically the fastest that a μC can drive the
MAX148/MAX149. Figure 11b shows the serial-
interface timing necessary to perform a conversion every
16 SCLK cycles in external clock mode.
__________ Applic ations Information
Power-On Reset
When power is first applied, and if
SHDN
is not pulled
low, internal power-on reset circuitry activates the
MAX148/MAX149 in internal clock mode, ready to con-
vert with SSTRB = high. After the power supplies stabi-
lize, the internal reset time is 10μs, and no conversions
should be performed during this phase. SSTRB is high
on power-up and, if
CS
is low, the first logical 1 on DIN
is interpreted as a start bit. Until a conversion takes
place, DOUT shifts out zeros. (Also see Table 4.)
Referenc e-Buffer Compensation
In addition to its shutdown function,
SHDN
selects inter-
nal or external compensation. The compensation
affects both power-up time and maximum conversion
speed. The100kHz minimum clock rate is limited by
droop on the sample-and-hold and is independent of
the compensation used.
Float
SHDN
to select external compensation. The
Typical Operating Circuit uses a 4.7μF capacitor at
VREF. A 4.7μF value ensures reference-buffer stability
and allows converter operation at the 2MHz full clock
speed. External compensation increases power-up
time (see the Choosing Power-Down Mode section and
Table 4).
Pull
SHDN
high to select internal compensation.
Internal compensation requires no external capacitor at
VREF and allows for the shortest power-up times. The
maximum clock rate is 2MHz in internal clock mode
and 400kHz in external clock mode.
Choosing Power-Down Mode
You can save power by placing the converter in a low-
current shutdown state between conversions. Select full
power-down mode or fast power-down mode via bits 1
and 0 of the DIN control byte with
SHDN
high or floating
(Tables 1 and 5). In both software power-down modes,
the serial interface remains operational, but the ADC
does not convert. Pull
SHDN
low at any time to shut
down the converter completely.
SHDN
overrides bits 1
and 0 of the control byte.
Full power-down mode turns off all chip functions that
draw quiescent current, reducing supply current to 2μA
(typ). Fast power-down mode turns off all circuitry
except the bandgap reference. With fast power-down
mode, the supply current is 30μA. Power-up time can be
shortened to 5μs in internal compensation mode.
Table 4 shows how the choice of reference-buffer com-
pensation and power-down mode affects both power-up
REFERENCE
BUFFER
REFERENCE-
BUFFER
COMPENSATION
MODE
Internal
Internal
External
External
—
—
VREF
CAPACITOR
(μF)
POWER-DOWN
MODE
POWER-UP
DELAY
(μs)
MAXIMUM
SAMPLING RATE
(ksps)
Enabled
Enabled
Enabled
Enabled
Disabled
Disabled
—
—
4.7
4.7
—
—
Fast
Full
Fast
Full
Fast
Full
5
26
26
133
133
133
133
300
See Figure 14c
See Figure 14c
2
2
Table 4. Typical Power-Up Delay Times
相關PDF資料 |
PDF描述 |
|---|---|
| MAX1480 | Digital Temperature Sensor with 2-Wire Interface 8-SOIC -40 to 125 |
| MAX1480E-MAX1490E | 15kV ESD-Protected, Isolated RS-485/RS-422 |
| MAX1480ECCPI | 15kV ESD-Protected, Isolated RS-485/RS-422 |
| MAX1490EAEPG | 15kV ESD-Protected, Isolated RS-485/RS-422 |
| MAX1480ECEPI | 15kV ESD-Protected, Isolated RS-485/RS-422 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX149ACPP+ | 功能描述:模數轉換器 - ADC 10-Bit 8Ch 133ksps 5.25V Precision ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX149AEAP | 功能描述:模數轉換器 - ADC Integrated Circuits (ICs) RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX149AEAP+ | 功能描述:模數轉換器 - ADC 10-Bit 8Ch 133ksps 5.25V Precision ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX149AEAP+T | 功能描述:模數轉換器 - ADC 10-Bit 8Ch 133ksps 5.25V Precision ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX149AEAP-T | 功能描述:模數轉換器 - ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
發布緊急采購，3分鐘左右您將得到回復。