- 您現在的位置：買賣IC網 > PDF目錄383320 > MAX1498ECJ (MAXIM INTEGRATED PRODUCTS INC) 3.5- and 4.5-Digit, Single-Chip ADCs with LED Drivers PDF資料下載
參數資料
| 型號： | MAX1498ECJ |
| 廠商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分類： | ADC |
| 英文描述： | 3.5- and 4.5-Digit, Single-Chip ADCs with LED Drivers |
| 中文描述： | 1-CH PROPRIETARY METHOD ADC, PQFP32 |
| 封裝： | 7 X 7 MM, 1.40 MM HEIGHT, MO-136, TQFP-32 |
| 文件頁數： | 18/24頁 |
| 文件大?。?/td> | 907K |
| 代理商： | MAX1498ECJ |
M
3.5- and 4.5-Digit, Single-Chip ADCs
with LED Drivers
18
______________________________________________________________________________________
Selecting Segment Current
A resistor from ISET to ground sets the current for each
LED segment. See Table 5 for more detail. Use the fol-
lowing formula to set the segment current:
R
ISET
values below 25k
increase the I
SEG
. However,
the internal current-limit circuit limits the I
SEG
to less than
30mA. At higher I
SEG
values, proper operation of the
device is not guaranteed. In addition, the power dissipat-
ed may exceed the package power-dissipation limit.
Choosing Supply Voltage to Minimize
Power Dissipation
The MAX1447/MAX1496/MAX1498 drive a peak current
of 25.5mA into LEDs with a 2.2V forward voltage drop
when operated from a supply voltage of at least 3.0V.
Therefore, the minimum voltage drop across the inter-
nal LED drivers is (3.0V - 2.2V) = 0.8V. The MAX1447/
MAX1496/MAX1498 sink (8 x 25.5mA = 204mA) when
the outputs are operating and the LED segment drivers
are at full current. For a 3.3V supply, the MAX1447/
MAX1496/MAX1498 dissipate (3.3V - 2.2V) x 204 =
224.4mW. If a higher supply voltage is used, the driver
absorbs a higher voltage, and the driver’s power dissi-
pation increases accordingly. However, if the LEDs
used have a higher forward voltage drop than 2.2V, the
supply voltage must be raised accordingly to ensure
that the driver always has at least 0.8V headroom.
For a VLED supply voltage of 2.7V, the maximum LED
forward voltage is 1.9V to ensure 0.8V driver headroom.
The voltage drop across the drivers with a nominal +5V
supply (5.0V - 2.2V = 2.8V) is almost three times the
drop across the drivers with a nominal 3.3V supply
(3.3V - 2.2V = 1.1V). Therefore, the driver’s power dissi-
pation increases three times. The power dissipation in
the part causes the junction temperature to rise accord-
ingly. In the high ambient temperature case, the total
junction temperature may be very high (>+125°C). At
higher junction temperatures, the ADC performance
degrades. To ensure the dissipation limit for the
MAX1447/MAX1496/MAX1498 is not exceeded and the
ADC performance is not degraded, a diode can be
inserted between the power supply and VLED.
Computing Power Dissipation
The following can be used to compute power dissipation:
PD = (VLED x I
VLED
) + (VLED - V
DIODE
)
(DUTY x I
SEG
x N) + V
SUPPLY
x I
SUPPLY
VLED = LED driver supply voltage
I
VLED
= VLED bias current
V
DIODE
= LED forward voltage
DUTY = segment ON time during each digit ON time
I
SEG
= segment current set by R
ISET
N = number of segments driven (worst case is eight)
V
SUPPLY
= supply voltage of the part
I
SUPPLY
= supply current from V
DD
for the MAX1496 or
AV
DD
+ DV
DD
for the MAX1447/MAX1498.
Dissipation Example
For I
SEG
= 25.5mA, N = 8, DUTY = 127 / 128, V
DIODE
=
1.5V at 25.5mA, VLED = V
SUPPLY
= 5.25V:
PD = (5.25 x 2mA) + (5.25V - 1.5) [(127 / 128)
x 25.5mA x 8)] + 5.25 x 1.080mA
PD = 0.7751W
28-Pin SSOP-Package Example
For the 28-pin SSOP package (T
JA
= 1 / 0.009496 =
+105.3°C/W), the maximum allowed ambient tempera-
ture T
A
is given by:
T
J
(max) = T
A
+ (PD x T
JA
) =
+125°C = T
A
+ (0.7751W x +105.3°C/W)
T
A
= +43°C
Thus, the device cannot operate safely at a maximum
package temperature of +85°C. The power dissipates
in the part need to be lowered.
I
V
R
SEG
ISET
=
×
1 20
.
450
R
ISET
(k
)
25
50
100
500
>2500
I
SEG
(mA)
21.6
10.8
5.4
1.1
LED driver disabled
Table 5. Segment-Current Selection
相關PDF資料 |
PDF描述 |
|---|---|
| MAX1447ECJ | 3.5- and 4.5-Digit, Single-Chip ADCs with LED Drivers |
| MAX1449 | 1C Remote and Local TEMPERATURE SENSOR with N-Factor and Series Resistance Correction 16-SSOP/QSOP -40 to 125 |
| MAX1449EHJ | Analog-to-Digital Converter， 10-Bit |
| MAX144ACPA | +2.7V, Low-Power, 2-Channel, 108ksps, Serial 12-Bit ADCs in 8-Pin レMAX |
| MAX144AEPA | LJT 37C 37#22D SKT PLUG |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX1498ECJ+ | 功能描述:模數轉換器 - ADC 4.5 Digit ADC w/LED Drivers RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX1498ECJ+T | 功能描述:模數轉換器 - ADC 4.5 Digit ADC w/LED Drivers RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX1498ECJ-T | 功能描述:模數轉換器 - ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX14998ETO+ | 功能描述:模擬開關 IC 4Ch DisplayPort MUX RoHS:否 制造商:Texas Instruments 開關數量:2 開關配置:SPDT 開啟電阻（最大值）:0.1 Ohms 切換電壓（最大）: 開啟時間（最大值）: 關閉時間（最大值）: 工作電源電壓:2.7 V to 4.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:DSBGA-16 |
| MAX14998ETO+T | 功能描述:模擬開關 IC 4Ch DisplayPort MUX RoHS:否 制造商:Texas Instruments 開關數量:2 開關配置:SPDT 開啟電阻（最大值）:0.1 Ohms 切換電壓（最大）: 開啟時間（最大值）: 關閉時間（最大值）: 工作電源電壓:2.7 V to 4.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:DSBGA-16 |
發布緊急采購，3分鐘左右您將得到回復。